HEADSUP!!! USB MFC committed..

[Michael E. Mercer]

Hello,

I have an ASUS P4C-800-E Deluxe Motherboard, P4 3.0GHz
processor with builtin USB 2.0 controllers.

I am having a problem with the Lexar Media JumpDrive 2.0 Pro 256M memory
keystick.

usbd nevers sees it. I finally went into BIOS and set the Speed for the
USB 2.0  Controller to FullSpeed (maybe HighSpeed, in whatever case its
12MBps as opposed to 240MBps). When setting it to 12MBps, usbd sees the
drive and attaches it. Setting the speed to higher, usbd does NOT attach
it.

Also NOTE: I have a SIIG SlimHub 2.0 4 ports, that I can not attach my
JumpDrive too. I must set the speed to 12MBps and attach it directly to
a port on my PC to get it to see it.

Any help in this would be appreciated.

Thanks!
Michael E. Mercer

My system is the latest 4.9-Stable build as of yesterday.

uname -a
FreeBSD fast.mmercer.com 4.9-STABLE FreeBSD 4.9-STABLE #0: Sat Mar 27
10:36:58 EST 2004     mmercer at fast.mmercer.com:/usr/src/sys/compile/g49 
i386

With a kernel built today Mar 27th.

dmesg inline...

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 4.9-STABLE #0: Sat Mar 27 10:36:58 EST 2004
    mmercer at fast.mmercer.com:/usr/src/sys/compile/g49
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3006.83-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
 
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 1072889856 (1047744K bytes)
avail memory = 1039900672 (1015528K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
IOAPIC #0 intpin 17 -> irq 10
IOAPIC #0 intpin 18 -> irq 5
IOAPIC #0 intpin 19 -> irq 11
FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs
 cpu0 (BSP): apic id:  0, version: 0x00050014, at 0xfee00000
 cpu1 (AP):  apic id:  1, version: 0x00050014, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00178020, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc0426000.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 12 entries at 0xc00f50e0
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82875P host to AGP bridge> mem 0xd0000000-0xdfffffff at
device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=8086 device=2579)> at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pci1: <NVidia model 0322 graphics accelerator> at 0.0 irq 10
pcib2: <PCI to PCI bridge (vendor=8086 device=257b)> at device 3.0 on
pci0
pci2: <PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port
0xcf80-0xcf9f mem 0xfe9e0000-0xfe9fffff irq 5 at device 1.0 on pci2
em0:  Speed:N/A  Duplex:N/A
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xef00-0xef1f
irq 10 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xef20-0xef3f
irq 11 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xef40-0xef5f
irq 5 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xef80-0xef9f
irq 10 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <USB controller> at 29.7 irq 11
pcib3: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on
pci0
pci3: <PCI bus> on pcib3
fwohci0: <VIA VT6306> port 0xdc00-0xdc7f mem 0xfeaff800-0xfeafffff irq 5
at device 3.0 on pci3
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 8.
fwohci0: EUI64 00:e0:18:00:00:58:2a:e6
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:e0:18:58:2a:e6
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on
pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 ATA100 controller> port
0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 10
pcm0: <Intel ICH5 (82801EB)> port 0xee80-0xeebf,0xe800-0xe8ff mem
0xfebff400-0xfebff4ff,0xfebff800-0xfebff9ff irq 10 at device 31.5 on
pci0
pcm0: <Analog Devices AD1985 AC97 Codec>
orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
ad0: 39205MB <Maxtor 6E040L0> [79656/16/63] at ata0-master UDMA100
ad3: 194481MB <Maxtor 6Y200P0> [395136/16/63] at ata1-slave UDMA100
acd0: DVD-R <OPTORITEDVD RW DD0203> at ata1-master PIO4
Mounting root from ufs:/dev/ad3s1a
em0: Link is up 100 Mbps Full Duplex
em0: Link is up 100 Mbps Full Duplex