[sun] Booting problem with Sun Enterprise 220R

ronan ron at artful.net
Mon May 7 14:22:56 UTC 2007

Hi all,

I am trying to install from 6.2-STABLE-200704-sparc64-bootonly.iso 
(it is the same from the 7.0 CURRENT snapshot)
But I cant, it crash during booting the kernel. Here is the boot log :


Ethernet address 8:0:20:xx:xx:xx, Host ID: 80c823eb.

Rebooting with command: boot /pci at 1f,4000/scsi at 3/disk at 6,0:f          
Boot device: /pci at 1f,4000/scsi at 3/disk at 6,0:f  File and args:
 >> FreeBSD/sparc64 boot block
   Boot path:   /pci at 1f,4000/scsi at 3/disk at 6,0:f
   Boot loader: /boot/loader
Consoles: Open Firmware console 
Boot path set to /pci at 1f,4000/scsi at 3/disk at 6,0:a

FreeBSD/sparc64 bootstrap loader, Revision 1.0
(root at edmunds.cse.buffalo.edu, Mon Apr  2 00:37:48 UTC 2007)
bootpath="/pci at 1f,4000/scsi at 3/disk at 6,0:a"
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x56f408+0x5bfa8 syms=[0x8+0x6d7b8+0x8+0x5b032]
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...              
nothing to autoload yet.
jumping to kernel entry at 0xc0060000.
stray vector interrupt 2029
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE-200704 #0: Mon Apr  2 16:12:13 UTC 2007
    root at edmunds.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
real memory  = 2147483648 (2048 MB)
avail memory = 2063147008 (1967 MB)
cpu0: Sun Microsystems UltraSparc-II Processor (450.05 MHz CPU)
cpu1: Sun Microsystems UltraSparc-II Processor (450.05 MHz CPU)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
ath_hal: (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, 
nexus0: <Open Firmware Nexus device>
pcib0: <U2P UPA-PCI bridge> on nexus0
pcib0: Psycho, impl 0, version 4, ign 0x7c0, bus B
pcib0: [FAST]
pcib0: [FAST]
pcib0: [FAST]
initializing counter-timer
Timecounter "counter-timer" frequency 1000000 Hz quality 100
pcib0 dvma: DVMA map: 0xfc000000 to 0xffffffff
pci0: <OFW PCI bus> on pcib0
ebus0: <PCI-EBus2 bridge> mem 
0x70000000-0x70ffffff,0x71000000-0x717fffff at device 1.0 on pci0
auxio0: <Sun Auxiliary I/O> addr 
on ebus0
ebus0: <power> addr 0x1400724000-0x1400724003 (no driver attached)
ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver attached)
ebus0: <sc> addr 0x1400500000-0x1400500007 (no driver attached)
puc0: <Siemens SAB 82532 dual channel SCC> addr 
0x1400400000-0x140040007f irq 43 on ebus0
uart0: <SAB 82532 v3.2, channel A> on puc0
uart0: CTS oflow
uart0: console (9600,n,8,1)
uart1: <SAB 82532 v3.2, channel B> on puc0
uart1: CTS oflow
uart2: <16550 or compatible> addr 0x14003083f8-0x14003083ff irq 41 on ebus0
uart2: keyboard (1200,n,8,1)
uart2: keyboard not present
uart3: <16550 or compatible> addr 0x14003062f8-0x14003062ff irq 42 on ebus0
ebus0: <ecpp> addr 
irq 34 (no driver attached)
ebus0: <fdthree> addr 
irq 39 (no driver attached)
eeprom0: <EEPROM/clock> addr 0x1400000000-0x1400001fff on ebus0
eeprom0: model mk48t59
eeprom0: hostid 80c823eb
ebus0: <flashprom> addr 0x1000000000-0x10000fffff (no driver attached)
hme0: <Sun HME 10/100 Ethernet> mem 0x500000-0x507fff at device 1.1 on pci0
miibus0: <MII bus> on hme0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hme0: Ethernet address: 08:00:20:c8:23:eb
sym0: <875> port 0x2000-0x20ff mem 0x508000-0x5080ff,0x50a000-0x50afff 
at device 3.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x2400-0x24ff mem 0x50c000-0x50c0ff,0x50e000-0x50efff 
at device 3.1 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
pci0: <serial bus, Fibre Channel> at device 2.0 (no driver attached)
pcib1: <OFW PCI-PCI bridge> at device 4.0 on pci0
pci1: <OFW PCI bus> on pcib1
isp0: <Qlogic ISP 10160 PCI SCSI Adapter> port 0x1000-0x10ff mem 
0x100000-0x100fff at device 4.0 on pci1
panic: trap: data access error
cpuid = 0
Uptime: 1s
Automatic reboot in 15 seconds - press a key on the console to abort


Is there any solution ? Is it a compatibility problem with the Qlogic 
ISP 10160 ?

Best regards,


More information about the freebsd-sparc64 mailing list