Need help

[Igor V. Ruzanov]

Hello, FreeBSD colleagues!

I have modern network card Intel i350T2V2 (peripheral dual gigabit port 
NIC). And as far as i know all Intel cards should be normally detected by 
the system. But with this NIC i have some troubles:
- the system sees the card as some ethernet device but cannot find 
proper (igb) driver:
pcib6: <ACPI PCI-PCI bridge> irq 47 at device 3.2 on pci0
pci6: <ACPI PCI bus> on pcib6
pci6: <network, ethernet> at device 0.0 (no driver attached)
pci6: <network, ethernet> at device 0.1 (no driver attached)
- its from dmesg log.

Fnd `pciconf -lcvb' says:
none75 at pci0:6:0:0:      class=0x020000 card=0x00008086 chip=0x151f8086 
rev=0x01 hdr=0x00
     vendor     = 'Intel Corporation'
     class      = network
     subclass   = ethernet
     bar   [10] = type Memory, range 32, base 0x91920000, size 131072, 
enabled
     bar   [18] = type I/O Port, range 32, base 0x2020, size 32, enabled
     bar   [1c] = type Memory, range 32, base 0x919c4000, size 16384, 
enabled
     cap 01[40] = powerspec 3  supports D0 D3  current D0
     cap 05[50] = MSI supports 1 message, 64 bit, vector masks
     cap 11[70] = MSI-X supports 10 messages
                  Table in map 0x1c[0x0], PBA in map 0x1c[0x2000]
     cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS link 
x4(x4)
                  speed 5.0(5.0) ASPM disabled(L0s/L1)
     ecap 0001[100] = AER 2 0 fatal 0 non-fatal 1 corrected
     ecap 000e[150] = ARI 1
     ecap 0010[160] = SRIOV 1
     ecap 0017[1a0] = TPH Requester 1
     ecap 0018[1c0] = LTR 1
     ecap 000d[1d0] = ACS 1
none76 at pci0:6:0:1:      class=0x020000 card=0x00008086 chip=0x151f8086 
rev=0x01 hdr=0x00
     vendor     = 'Intel Corporation'
     class      = network
     subclass   = ethernet
     bar   [10] = type Memory, range 32, base 0x91900000, size 131072, 
enabled
     bar   [18] = type I/O Port, range 32, base 0x2000, size 32, enabled
     bar   [1c] = type Memory, range 32, base 0x919c0000, size 16384, 
enabled
     cap 01[40] = powerspec 3  supports D0 D3  current D0
     cap 05[50] = MSI supports 1 message, 64 bit, vector masks
     cap 11[70] = MSI-X supports 10 messages
                  Table in map 0x1c[0x0], PBA in map 0x1c[0x2000]
     cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS link 
x4(x4)
                  speed 5.0(5.0) ASPM disabled(L0s/L1)
     ecap 0001[100] = AER 2 0 fatal 0 non-fatal 1 corrected
     ecap 000e[150] = ARI 1
     ecap 0010[160] = SRIOV 1
     ecap 0017[1a0] = TPH Requester 1
     ecap 000d[1d0] = ACS 1

My server is:
- system is FreeBSD-10.3-RELEASE-p20
- motherboard: Intel S2600WT (dual CPU socket board)
- one CPU installed

Maybe someone has experience with this inetl NIC? As seen from pciconf 
output the NIC has a set of VFs (Virtual Functions) needed in 
virtualization environments. And chip id is 0x151F8086 - the id that 
igb-driver does not know about. Maybe i need some preconfiguration of this 
card? Or this device is not compatible with non-virtualization systems 
like usual physical server?

Big thanks in advance!