bwi: no DS tssi no OFDM tssi

[Neal Hogan]

Hello,

   I am attempting to get by broadcom wifi card up and running, am sick of
trying to get ndis working, and am attempting to use the bwi driver
(originating in dragonflyBSD). I'm hoping others here have tried to do the
same and have some pointers. I'm using 7.1-RELEASE (system/source are
in-sync) and my card is a BCM94306MP. My dmesg is posted below.

Bwi(4) is installed and it recognizes my card (*if_bwi_load-"YES"* is in my
/etc/rc.conf and *bwi_v3* and *if_bwi* are loaded). I can send a IP request
to my WEP encrypted access point. Yet, it doesn't get an offer and says that
*no DS tssi* and *no OFDM tssi* Being new to bwi(4) and have never seen
references to DS/OFDM tssi, I'm not sure what info to provide. My research
is not leading anywhere helpful.  Thanks.




Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE #0: Sat Jan 10 19:07:15 CST 2009
    nph at frege.lambdaserver:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: mobile AMD Athlon(tm) XP2400+ (1788.94-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x6a0  Stepping = 0
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0480800<SYSCALL,MP,MMX+,3DNow!+,3DNow!>
real memory  = 468647936 (446 MB)
avail memory = 444530688 (423 MB)
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <PTLTD   RSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x18> port 0x62,0x66 on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci_link5: BIOS IRQ 10 for 0.10.INTA is invalid
pci0: <ACPI PCI bus> on pcib0
agp0: <ATI RS100 AGP bridge> on hostb0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x9000-0x90ff mem
0xe0000000-0xefffffff,0xd0100000-0xd010ffff irq 10 at device 5.0 on
pci1
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem
0xd0006000-0xd0006fff irq 9 at device 2.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 4 ports with 4 removable, self powered
pcm0: <Acer Labs M5451> port 0x8400-0x84ff mem 0xd0007000-0xd0007fff
irq 5 at device 6.0 on pci0
pcm0: <Conexant CX20468 AC97 Codec>
pcm0: [GIANT-LOCKED]
pcm0: [ITHREAD]
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <simple comms, generic modem> at device 8.0 (no driver attached)
bwi0: <Broadcom BCM4306v1 802.11 Wireless Lan> mem
0xd0004000-0xd0005fff irq 9 at device 9.0 on pci0
bwi0: [ITHREAD]
bwi0: regwin: chipcommon (0x800), rev 2, vendor 0x4243
bwi0: BBP: id 0x4306, rev 0x2, pkg 0
bwi0: nregwin 6, cap 0x0000002a
bwi0: regwin: 802.11 MAC (0x812), rev 4, vendor 0x4243
bwi0: has TX stats
bwi0: MAC: rev 4
bwi0: regwin: pcmcia (0x80d), rev 1, vendor 0x4243
bwi0: regwin: v90 codec (0x807), rev 1, vendor 0x4243
bwi0: regwin: pci (0x804), rev 7, vendor 0x4243
bwi0: regwin: 802.11 MAC (0x812), rev 4, vendor 0x4243
bwi0: ignore second MAC
bwi0: bus rev 0
bwi0: pci is enabled
bwi0: card flags 0x000f
bwi0: 0th led, act 3, lowact 0
bwi0: 1th led, act 5, lowact 0
bwi0: 2th led, act 4, lowact 0
bwi0: 3th led, act 0, lowact 0
bwi0: 802.11 MAC was already disabled
bwi0: PHY is linked
bwi0: PHY: type 2, rev 1, ver 1
bwi0: PHY: 802.11G attach
bwi0: RF: manu 0x17f, type 0x2050, rev 2
bwi0: bus rev 0
bwi0: PHY is linked
bwi0: 30bit bus space
bwi0: max txpower from sprom: 57 dBm
bwi0: invalid antenna gain in sprom
bwi0: ant gain 8 dBm
bwi0: region/domain max txpower 76 dBm
bwi0: max txpower 57 dBm
bwi0: sprom idle tssi: 0x003e
bwi0: TSSI-TX power map:
71 71 70 70 70 70 70 69
69 69 69 69 68 68 68 67
67 67 66 66 66 66 65 65
65 64 64 64 63 63 63 62
61 61 61 60 59 59 58 57
57 55 55 54 53 52 51 50
49 48 47 44 43 42 39 37
35 32 29 26 22 18 14 8
bwi0: idle tssi0: 62
bwi0: bus rev 0
bwi0: locale: 6
bwi0: WARNING: using obsoleted if_watchdog interface
bwi0: Ethernet address: 00:90:4b:61:02:45
cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 11 at device 10.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
fwohci0: <Texas Instruments TSB43AB21/A/AI/A-EP> mem
0xd0009000-0xd00097ff,0xd0000000-0xd0003fff irq 10 at device 12.0 on
pci0
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:0d:9d:71:9e:43:0c:6a
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:0d:9d:43:0c:6a
fwe0: Ethernet address: 02:0d:9d:43:0c:6a
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:0d:9d:71:9e:43:0c:6a @ 0xfffe00000000,
S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x12bc000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
atapci0: <AcerLabs M5229 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8080-0x808f at device 16.0 on
pci0
atapci0: using PIO transfers above 137GB as workaround for 48bit DMA
access bug, expect reduced performance
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <bridge> at device 17.0 (no driver attached)
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x8c00-0x8cff mem
0xd000a000-0xd000afff irq 11 at device 18.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
nsphyter0: <DP83815 10/100 media interface> PHY 0 on miibus0
nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:9d:43:2b:a7
sis0: [ITHREAD]
acpi_button0: <Power Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
cpu0: <ACPI CPU> on acpi0
powernow0: <PowerNow! K7> on cpu0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcefff,0xcf000-0xcf7ff,0xdb000-0xdbfff,0xdc000-0xdffff pnpid
ORM0000 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: [ITHREAD]
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
plip0: WARNING: using obsoleted IFF_NEEDSGIANT flag
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: <Logitech USB Receiver, class 0/0, rev 1.10/25.00, addr 2> on uhub0
ums0: 16 buttons and Z dir.
Timecounter "TSC" frequency 1788943467 Hz quality 800
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 95396MB <Seagate ST9100823A 3.02> at ata0-master UDMA100
acd0: CDRW <QSI CD-RW/DVD-ROM SBW-241/VH04> at ata1-master UDMA33
Trying to mount root from ufs:/dev/ad0s2a
bwi0: bwi_init
bwi0: bwi_stop
bwi0: bbp atten: 0, rf atten: 3, ctrl1: 2, ctrl2: 65535
bwi0: bus rev 0
bwi0: 802.11 MAC is disabled
bwi0: 802.11 MAC was already disabled
bwi0: PHY is linked
bwi0: bus rev 0
bwi0: PHY is unlinked
bwi0: RF calibration value: 0x002a
bwi0: bus rev 0
bwi0: PHY is linked
firmware_get: failed to load firmware image bwi_v3_ucode4
bwi0: request firmware bwi_v3_ucode4 failed
bwi0: bwi_stop




-- 
www.nealhogan.net