Missing SATA drive after upgrade to 7.0
Snow Mountains
snow.mountains.4 at gmail.com
Wed Mar 26 12:23:25 PDT 2008
2008/3/25, Christopher Cowart <ccowart at rescomp.berkeley.edu>:
> Hello,
>
> I was in the process of upgrading from 6.2 to 7.0. After the
> installkernel, I rebooted into single, only to find the mountroot
> prompt:
>
> | Trying to mount root from ufs:/dev/ad2s1a
> |
> | Manual root filesystem specification:
> | <fstype>:<device> Mount <device> using filesystem <fstype>
> | eg. ufs:da0s1a
> | ? List valid disk boot devices
> | <empty line> Abort manual input
> |
> | mountroot> ?
> |
> | List of GEOM managed disk devices:
> | acd0 fd0
>
> Boot messages for 7.0 (grep -i ata dmesg-7.0):
> | atapci0: <Intel 6300ESB SATA150 controller> port
> | 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1470-0x147f at device 31.2
> | on pci0
> | ata0: <ATA channel 0> on atapci0
> | ata0: [ITHREAD]
> | ata1: <ATA channel 1> on atapci0
> | ata1: [ITHREAD]
> | acd0: CDROM <LG CD-ROM CRN-8245B/1.16> at ata0-master UDMA33
>
> Boot messages for 6.2 (grep -i ata dmesg-6.2):
> | atapci0: <Intel 6300ESB SATA150 controller> port
> | 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1470-0x147f at device 31.2
> | on pci0
> | ata0: <ATA channel 0> on atapci0
> | ata1: <ATA channel 1> on atapci0
> | acd0: CDROM <LG CD-ROM CRN-8245B/1.16> at ata0-master UDMA33
> | ad2: 76324MB <Seagate ST380013AS 3.25> at ata1-master SATA150
>
> Any ideas where my harddrive went? I can `boot kernel.old' without any
> problems. I think this post [1] might be related. Unfortunately, the
> problem went away for the person who submitted the referenced PR.
>
> [1] http://lists.freebsd.org/pipermail/freebsd-i386/2008-January/006239.html
>
>
Hey, I have same problem with my old computer:
atapci0: <Intel PIIX4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 2.1 on
pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
ad1: 76319MB <WDC WD800JB-00JJC0 05.01C05> at ata0-slave UDMA33
acd0: CDRW <CD-W540E/1.0C> at ata1-master UDMA33
Also, it waits 10 seconds after "ata0: <ATA channel 0> on atapci0", true ?
If you reboot 3-4 times it will pass and everything will work
normally. Then, I tried with disabled ACPI and it booted always
without problems. However, then I recompiled GENERIC kernel because of
HPLIP and now situation is opposite: it always boots with ACPI but not
with ACPI. Very strange...
SergiM
More information about the freebsd-questions
mailing list