Cant install freebsd6.2 on RAID1

[Toomas Aas]

N, 19 apr   2007 kirjutas "М. Павел" <MPavel at yandex.ru>:

> Good Day.
>
> I▓ve got a problem:
> Server:
> -	Motherboard Intel SE7320ep2 with integrated, simple, but fully   
> hardware raid controller.
> -	Two HDDs Seagate 200 gb combined into raid 1 (mirror).
>
> The HDD has 3 sections:
> 3 √ not formated
> 1 √ win2003 server
> 2 √ keeps logic drives for windows
> (there number means diskpart, not a order)
>
> While booting from installation CD (on device probing stage) i've   
> got following message:
> ...
> atapci0: <Intel 6300ESB UDMA100 controller> port   
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on   
> pci0
> ata0: <ATA channel 0> on atapci0
> ata1: <ATA channel 1> on atapci0
> atapci1: <Intel 6300ESB SATA150 controller> port   
> 0xce80-0xce87,0xce00-0xce03,0xcd80-0xcd87,0xcd00-0xcd03,0xcc80-0xcc8f irq 18  
>  at device 31.2 on pci0
> ata2: <ATA channel 0> on atapci1
> ata3: <ATA channel 1> on atapci1
> ...
> ad4: 188348MB <Seagate ST3300831AS 3.03> at ata2-master SATA150
> ad6: 188348MB <Seagate ST3300831AS 3.03> at ata3-master SATA150
> ar0: 188348MB <LSILogic v3 MegaRAID RAID1> status: READY
> ar0: disk0 READY (master) using ad4 at ata2-master
> ar0: disk1 READY (mirror) using ad6 at ata3-master
> ...
>
> During the installation of freebsd6.2 there are 3 variants where   
> freebsd can be established: ad4,ad6,ar0.
> I install the program to the drive ar0, make a slice on it and   
> install the Boot Manager in MBR.
> After the installation before rebooting the system I make sure that   
> everything I need was copied.
>
> Also i checked what says atacontrol
>> atacontrol status ar0
> ar0: ATA RAID 1 subdisks: ad4 ad6 status:READY
>
> and pciconf:
>> pciconf -lv
> ...
> atapci0 at pci0:31:1:      class=0x01018a card=0x34508086   
> chip=0x25a28086 rev=0x02 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '6300ESB IDE Controller'
>     class    = mass storage
>     subclass = ATA
> atapci1 at pci0:31:2:      class=0x01048f card=0x34518086   
> chip=0x25b08086 rev=0x02 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '6300ESB Serial ATA Controller (RAID mode)'
>     class    = mass storage
>     subclass = RAID
> ...
>
>
> This means that the drive is visible and freebsd defines it to be normal (?)
>
> Then Reboot.
>
> F1 - Successfully loads windows
> F3 - after BTX Loader I receive the following message: "can▓t load   
> kerner. Reason: not found"
>
> lsdev says
>> lsdev
> disk devices:
>   disk0: BIOS drive A:
>   disk1: BIOS drive C:
>
>> show currdev
> disk1s3a
>
> However while i loading from installation CD
>> lsdev
> disk devices:
>   disk0: BIOS drive A:
>   disk1: BIOS drive C:
>     disk1s3a: FFS
>     disk1s3b: swap
>     disk1s3d: FFS
>     disk1s3e: FFS
>     disk1s3f: FFS
>
> After that I reboot the computer and raid controller reports that   
> the RAID is in DEGRADED state and drives need synchronization.
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to "freebsd-questions-unsubscribe at freebsd.org"
>



-- 
Toomas Aas