kernel: ad8: FAILURE - READ timed out LBA=234441585
Daniel A. A.
alive at dienub.org
Sun Jun 18 19:47:17 UTC 2006
Daniel A. A. wrote:
> Hi,
> Whenever I try to boot my desktop workstation with FreeBSD, it suddenly just
> hangs there forever. When I boot into safe mode, however, I get this in the
> dmesg:
> Jun 18 16:01:46 b00b kernel: ad8: 114473MB <Seagate ST3120022A 3.06> at
> ata4-master PIO4
> Jun 18 16:01:46 b00b kernel: ad8: FAILURE - READ timed out LBA=234441585
> Jun 18 16:01:46 b00b kernel: ad8: TIMEOUT - READ retrying (1 retry left) LBA=0
> Jun 18 16:01:46 b00b kernel: ad8: FAILURE - READ timed out LBA=234441631
> Jun 18 16:01:46 b00b kernel: ad8: TIMEOUT - READ retrying (0 retries left)
> LBA=0
> Jun 18 16:01:46 b00b kernel: ad8: FAILURE - READ timed out LBA=234441644
> Jun 18 16:01:46 b00b kernel: ad8: FAILURE - READ timed out LBA=0
> Jun 18 16:01:46 b00b kernel: ad8: FAILURE - READ timed out LBA=234441585
> Jun 18 16:01:46 b00b kernel: ad8: TIMEOUT - READ retrying (1 retry left) LBA=0
>
> The hard drive is connected to an onboard Promise FastTrak (atapci1: <Promise
> PDC20376 SATA150 controller> port 0x8000-0x803f,0x7800-0x780f,0x7400-0x747f
> mem 0xab800000-0xab800fff,0xab000000-0xab01ffff irq 11 at device 14.0 on
> pci0) controller on my Asus p4s8x motherboard. The drive itself is connected
> to the optional PATA connector, which works wonderfully in Windows.
>
> I've currently managed to install Xorg and KDE on the box, all entirely in
> Safe Mode, but the performance is really bad, or not as good as it should be
> on a PC with a Pentium IV 2.4GHz and 1GB PC3200 RAM.
> Googling yields irrelevant results to my case, and search results for "freebsd
> p4s8x" (no quotes) indicate that FreeBSD should be working OK with my
> motherboard and all of its native components.
>
> So, does anybody know how to
> a) Fix this issue (or, if not)
> b) How to prevent a specific device (atapci1 or ad8) from being loaded during
> boot time? Again, googling yields no results, but I might be querying the
> wrong strings.
>
> Attached is my dmesg.boot
>
> Thanks for any help.
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to "freebsd-questions-unsubscribe at freebsd.org"
Well, go figure.
First, I disabled the SATA controller which I thought was the problem,
in my BIOS. This didn't give any more different results than booting
normally, except that the ad8 device wasn't created. The system just
stopped loading after creating the acd0 device. So, that must not have
been the problem, I thought. Then I disconnected the power and ATA cable
from the "problematic" hard drive, which yielded the same results.
Then, I disconnected my DVD drive, which didn't change the situation at
all, except not creating the acd0 device at boot (And just hanging after
initiating ad1, which is where I boot FreeBSD from)
So I tried booting in verbose mode, which I hoped would give some error,
or at least a clue. It didn't. At all.
Then, my logic screamed at me, and I was smiling yet again. What if the
verbose mode would give me a clue as to how the system manages to boot
in safe mode? What if it tells me something like "this and that was
skipped, proceeding safe boot"? After having figured out how to boot in
safe AND verbose mode (By editing /boot/beastie.4th a little. Maybe
booting in safe mode should be a 'boot' flag?), I happily rebooted the
box again. Nothing broke from my edit, and it booted. I watched the
screen and the scrolling text in anticipation, like a little boy on
Christmas who is hoping that Santa will bring him the bike he's always
wanted.
As the kernel, very verbosely, complained about not being able to read
stuff on the ad8 device, this kids eyes lighted up. He approached the
Christmas tree, thinking that he had spotted the bike. And then, BAM.
Everything with this boys name on the label under the tree was a soft
package. Five packages from Santa; all soft. The kid lost hope, yet
again, as his highly anticipated informative error messages were nowhere
to find.
I've attached the verbose dmesg.boot, in the hopes that someone will
bring me a hard package with my name on it - before next Christmas.
-------------- next part --------------
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...8 8 4 3 3 0 0 done
All buffers synced.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE #0: Sun May 7 04:32:43 UTC 2006
root at opus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0abe000.
Preloaded elf module "/boot/kernel/snd_es137x.ko" at 0xc0abe188.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc0abe238.
Calibrating clock(s) ... i8254 clock: 1193262 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2400098244 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2400.10-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
real memory = 1073725440 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x000000003edc3fff, 1041887232 bytes (254367 pages)
avail memory = 1041780736 (993 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f1800
bios32: Entry = 0xf1180 (c00f1180) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x11b0
pnpbios: Found PnP BIOS data at 0xc00f9680
pnpbios: Entry = f0000:96b0 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
mem: <memory>
Pentium Pro MTRR support enabled
rr232x: RocketRAID 232x controller driver v1.02 (May 7 2006 04:32:33)
npx0: INT 16 interface
cpu0 on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000070
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=06481039)
pcibios: BIOS version 2.10
Found $PIR table, 11 entries at 0xc00f1720
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
slot 7 1 0 A 0x41 3 4 5 7 9 10 11 12
slot 7 1 0 B 0x42 3 4 5 7 9 10 11 12
embedded 0 2 A 0x41 3 4 5 7 9 10 11 12
embedded 0 2 B 0x42 3 4 5 7 9 10 11 12
embedded 0 2 C 0x43 3 4 5 7 9 10 11 12
embedded 0 2 D 0x44 3 4 5 7 9 10 11 12
embedded 0 3 A 0x60 3 4 5 7 9 10 11 12
embedded 0 3 B 0x61 3 4 5 7 9 10 11 12
embedded 0 3 C 0x62 3 4 5 7 9 10 11 12
embedded 0 3 D 0x63 3 4 5 7 9 10 11 12
slot 1 0 8 A 0x44 3 4 5 7 9 10 11 12
slot 1 0 8 B 0x41 3 4 5 7 9 10 11 12
slot 1 0 8 C 0x42 3 4 5 7 9 10 11 12
slot 1 0 8 D 0x43 3 4 5 7 9 10 11 12
slot 2 0 9 A 0x42 3 4 5 7 9 10 11 12
slot 2 0 9 B 0x43 3 4 5 7 9 10 11 12
slot 2 0 9 C 0x44 3 4 5 7 9 10 11 12
slot 2 0 9 D 0x41 3 4 5 7 9 10 11 12
slot 3 0 10 A 0x43 3 4 5 7 9 10 11 12
slot 3 0 10 B 0x44 3 4 5 7 9 10 11 12
slot 3 0 10 C 0x41 3 4 5 7 9 10 11 12
slot 3 0 10 D 0x42 3 4 5 7 9 10 11 12
slot 4 0 11 A 0x44 3 4 5 7 9 10 11 12
slot 4 0 11 B 0x41 3 4 5 7 9 10 11 12
slot 4 0 11 C 0x42 3 4 5 7 9 10 11 12
slot 4 0 11 D 0x43 3 4 5 7 9 10 11 12
slot 5 0 12 A 0x41 3 4 5 7 9 10 11 12
slot 5 0 12 B 0x42 3 4 5 7 9 10 11 12
slot 5 0 12 C 0x43 3 4 5 7 9 10 11 12
slot 5 0 12 D 0x44 3 4 5 7 9 10 11 12
slot 6 0 13 A 0x42 3 4 5 7 9 10 11 12
slot 6 0 13 B 0x43 3 4 5 7 9 10 11 12
slot 6 0 13 C 0x44 3 4 5 7 9 10 11 12
slot 6 0 13 D 0x41 3 4 5 7 9 10 11 12
embedded 0 4 A 0x44 3 4 5 7 9 10 11 12
embedded 0 14 A 0x41 3 4 5 7 9 10 11 12
embedded 0 14 B 0x42 3 4 5 7 9 10 11 12
embedded 0 14 C 0x43 3 4 5 7 9 10 11 12
embedded 0 14 D 0x44 3 4 5 7 9 10 11 12
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 11 Entries> on motherboard
$PIR: Links after initial probe:
Link IRQ Rtd Ref IRQs
0x41 255 N 9 3 4 5 7 9 10 11 12
0x42 255 N 9 3 4 5 7 9 10 11 12
0x43 255 N 8 3 4 5 7 9 10 11 12
0x44 255 N 9 3 4 5 7 9 10 11 12
0x60 255 N 1 3 4 5 7 9 10 11 12
0x61 255 N 1 3 4 5 7 9 10 11 12
0x62 255 N 1 3 4 5 7 9 10 11 12
0x63 255 N 1 3 4 5 7 9 10 11 12
$PIR: Found matching pin for 1.0.INTA at func 0: 11
$PIR: Found matching pin for 0.2.INTA at func 5: 11
$PIR: Found matching pin for 0.2.INTB at func 3: 255
$PIR: Found matching pin for 0.2.INTC at func 7: 255
$PIR: Found matching pin for 0.3.INTA at func 0: 9
$PIR: Found matching pin for 0.3.INTB at func 1: 9
$PIR: Found matching pin for 0.3.INTC at func 2: 9
$PIR: Found matching pin for 0.3.INTD at func 3: 255
$PIR: Found matching pin for 0.13.INTA at func 0: 255
$PIR: Found matching pin for 0.4.INTA at func 0: 255
$PIR: Found matching pin for 0.14.INTA at func 0: 11
$PIR: Links after initial IRQ discovery:
Link IRQ Rtd Ref IRQs
0x41 11 Y 9 3 4 5 7 9 10 11 12
0x42 255 N 9 3 4 5 7 9 10 11 12
0x43 255 N 8 3 4 5 7 9 10 11 12
0x44 255 N 9 3 4 5 7 9 10 11 12
0x60 9 Y 1 3 4 5 7 9 10 11 12
0x61 9 Y 1 3 4 5 7 9 10 11 12
0x62 9 Y 1 3 4 5 7 9 10 11 12
0x63 255 N 1 3 4 5 7 9 10 11 12
$PIR: IRQs used by BIOS: 9 11
$PIR: Interrupt Weights:
[ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
[ 0 0 0 0 0 0 0 0 0 3 0 9 0 0 0 0 ]
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1039, dev=0x0648, revid=0x02
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base b0000000, size 27, enabled
found-> vendor=0x1039, dev=0x0001, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1039, dev=0x0963, revid=0x04
bus=0, slot=2, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1039, dev=0x7007, revid=0x00
bus=0, slot=2, func=3
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0004, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x0c (3000 ns)
intpin=b, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ae800000, size 12, memory disabled
found-> vendor=0x1039, dev=0x5513, revid=0x00
bus=0, slot=2, func=5
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[20]: type 4, range 32, base 0000a400, size 4, enabled
$PIR: 0:2 INTA routed to irq 11
found-> vendor=0x1039, dev=0x7012, revid=0xa0
bus=0, slot=2, func=7
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0004, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x34 (13000 ns), maxlat=0x0b (2750 ns)
intpin=c, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 00009400, size 8, port disabled
map[14]: type 4, range 32, base 00009000, size 7, enabled
found-> vendor=0x1039, dev=0x7001, revid=0x0f
bus=0, slot=3, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=a, irq=9
map[10]: type 1, range 32, base ae000000, size 12, enabled
$PIR: 0:3 INTA routed to irq 9
found-> vendor=0x1039, dev=0x7001, revid=0x0f
bus=0, slot=3, func=1
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=b, irq=9
map[10]: type 1, range 32, base ad800000, size 12, enabled
$PIR: 0:3 INTB routed to irq 9
found-> vendor=0x1039, dev=0x7001, revid=0x0f
bus=0, slot=3, func=2
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=c, irq=9
map[10]: type 1, range 32, base ad000000, size 12, enabled
$PIR: 0:3 INTC routed to irq 9
found-> vendor=0x1039, dev=0x7002, revid=0x00
bus=0, slot=3, func=3
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0004, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=d, irq=255
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base ac800000, size 12, memory disabled
found-> vendor=0x1039, dev=0x0900, revid=0x91
bus=0, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0004, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x34 (13000 ns), maxlat=0x0b (2750 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 00008800, size 8, port disabled
map[14]: type 1, range 32, base ac000000, size 12, memory disabled
found-> vendor=0x1274, dev=0x5880, revid=0x02
bus=0, slot=13, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0004, statreg=0x0410, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x80 (32000 ns)
intpin=a, irq=255
powerspec 1 supports D0 D2 D3 current D0
map[10]: type 4, range 32, base 00008400, size 6, port disabled
found-> vendor=0x105a, dev=0x3376, revid=0x02
bus=0, slot=14, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x60 (2880 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D3 current D0
map[10]: type 4, range 32, base 00008000, size 6, enabled
map[14]: type 4, range 32, base 00007800, size 4, enabled
map[18]: type 4, range 32, base 00007400, size 7, enabled
map[1c]: type 1, range 32, base ab800000, size 12, enabled
map[20]: type 1, range 32, base ab000000, size 17, enabled
$PIR: 0:14 INTA routed to irq 11
agp0: <SiS 648 host to AGP bridge> mem 0xb0000000-0xb7ffffff at device 0.0 on pci0
agp0: Reserved 0x8000000 bytes for rid 0x10 type 3 at 0xb0000000
agp0: allocating GATT for aperture of size 128M
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: memory decode 0xaf000000-0xafffffff
pcib1: prefetched decode 0xc0000000-0xfebfffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x4151, revid=0x00
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base e0000000, size 28, enabled
pcib1: (null) requested memory range 0xe0000000-0xefffffff: good
map[14]: type 4, range 32, base 0000d800, size 8, enabled
pcib1: (null) requested I/O range 0xd800-0xd8ff: in range
map[18]: type 1, range 32, base af800000, size 16, enabled
pcib1: (null) requested memory range 0xaf800000-0xaf80ffff: good
$PIR: 1:0 INTA routed to irq 11
found-> vendor=0x1002, dev=0x4171, revid=0x00
bus=1, slot=0, func=1
class=03-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0004, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base c0000000, size 28, memory disabled
pcib1: (null) requested memory range 0xc0000000-0xcfffffff: good
map[14]: type 1, range 32, base af000000, size 16, enabled
pcib1: (null) requested memory range 0xaf000000-0xaf00ffff: good
pci1: <display, VGA> at device 0.0 (no driver attached)
pci1: <display> at device 0.1 (no driver attached)
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
fwohci0: <SiS 7007> mem 0xae800000-0xae800fff at device 2.3 on pci0
fwohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xae800000
$PIR: Found IRQ 9 for link 0x42 from 9 11
$PIR: ROUTE_INTERRUPT failed.
fwohci0: Could not allocate irq
device_attach: fwohci0 attach returned 6
atapci0: <SiS 963 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xa400-0xa40f irq 11 at device 2.5 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xa400
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: [MPSAFE]
pci0: <multimedia, audio> at device 2.7 (no driver attached)
ohci0: <SiS 5571 USB controller> mem 0xae000000-0xae000fff irq 9 at device 3.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xae000000
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xad800000-0xad800fff irq 9 at device 3.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xad800000
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ohci2: <SiS 5571 USB controller> mem 0xad000000-0xad000fff irq 9 at device 3.2 on pci0
ohci2: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xad000000
ohci2: [GIANT-LOCKED]
usb2: OHCI version 1.0, legacy support
usb2: SMM does not respond, resetting
usb2: <SiS 5571 USB controller> on ohci2
usb2: USB revision 1.0
uhub2: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xac800000-0xac800fff at device 3.3 on pci0
ehci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xac800000
$PIR: Found IRQ 9 for link 0x63 from 9 11
$PIR: ROUTE_INTERRUPT failed.
ehci0: Could not allocate irq
device_attach: ehci0 attach returned 6
sis0: <SiS 900 10/100BaseTX> port 0x8800-0x88ff mem 0xac000000-0xac000fff at device 4.0 on pci0
sis0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x8800
$PIR: Found IRQ 9 for link 0x44 from 9 11
$PIR: 0:4 INTA routed to irq 9
miibus0: <MII bus> on sis0
rlphy0: <RTL8201L 10/100 media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: bpf attached
sis0: Ethernet address: 00:e0:18:b0:e3:5b
sis0: [MPSAFE]
pcm0: <Creative CT5880-C> port 0x8400-0x843f at device 13.0 on pci0
pcm0: Reserved 0x40 bytes for rid 0x10 type 4 at 0x8400
pcm0: <SigmaTel STAC9708/11 AC97 Codec (id = 0x83847608)>
pcm0: Codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features surround DAC
pcm0: ac97 codec dac ready count: 0
$PIR: 0:13 INTA routed to irq 9
pcm0: [MPSAFE]
pcm0: sndbuf_setmap 3e8d5000, 1000; 0xc4bc1000 -> 3e8d5000
pcm0: sndbuf_setmap 3e8f7000, 1000; 0xc4bc3000 -> 3e8f7000
pcm0: <Playback: DAC2 / Record: ADC>
atapci1: <Promise PDC20376 SATA150 controller> port 0x8000-0x803f,0x7800-0x780f,0x7400-0x747f mem 0xab800000-0xab800fff,0xab000000-0xab01ffff irq 11 at device 14.0 on pci0
pci0: child atapci1 requested type 4 for rid 0x20, but the BAR says it is an memio
atapci1: [MPSAFE]
atapci1: Reserved 0x20000 bytes for rid 0x20 type 3 at 0xab000000
atapci1: Reserved 0x1000 bytes for rid 0x1c type 3 at 0xab800000
atapci1: [MPSAFE]
ata2: <ATA channel 0> on atapci1
ata2: SATA connect status=00000000
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci1
ata3: SATA connect status=00000000
ata3: [MPSAFE]
ata4: <ATA channel 2> on atapci1
ata4: reset tp1 mask=03 ostat0=50 ostat1=00
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: [MPSAFE]
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
pnpbios: 16 devices, largest 114 bytes
PNP0401: adding dma mask 0x8
PNP0401: adding irq mask 0x20
PNP0401: adding io range 0x278-0x27f, size=0x8, align=0
PNP0401: adding io range 0x678-0x67f, size=0x8, align=0
pnpbios: handle 1 device ID PNP0401 (0104d041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3e8-0x3ef, size=0x8, align=0
pnpbios: handle 2 device ID PNP0501 (0105d041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 3 device ID PNP0501 (0105d041)
PNPb02f: adding io range 0x200-0x207, size=0x8, align=0
pnpbios: handle 6 device ID PNPb02f (2fb0d041)
PNPb006: adding irq mask 0x400
PNPb006: adding io range 0x300-0x301, size=0x2, align=0
pnpbios: handle 7 device ID PNPb006 (06b0d041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 8 device ID PNP0f13 (130fd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x3fffffff, size=0x3ff00000
PNP0c01: adding fixed memory32 range 0xe8000-0xeffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xdbc00-0xdbfff, size=0x400
PNP0c01: adding fixed memory32 range 0xfff80000-0xffffffff, size=0x80000
pnpbios: handle 9 device ID PNP0c01 (010cd041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 11 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 12 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 13 device ID PNP0303 (0303d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xf0, size=0x1, align=0
pnpbios: handle 14 device ID PNP0c04 (040cd041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x80-0x90, size=0x11, align=0
PNP0200: adding io range 0x94-0x9f, size=0xc, align=0
PNP0200: adding io range 0xc0-0xde, size=0x1f, align=0
pnpbios: handle 15 device ID PNP0200 (0002d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 16 device ID PNP0800 (0008d041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
pnpbios: handle 17 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0xe600-0xe61f, size=0x20, align=0
PNP0c02: adding io range 0xe400-0xe47f, size=0x80, align=0
pnpbios: handle 18 device ID PNP0c02 (020cd041)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd3fff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0xffffffff (1)
atkbd: failed to reset the keyboard.
kbd0 at atkbd0
kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0047
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port found at 0x278
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x278-0x27f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x221 0x231 0x221 0x221
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x221 0x221 0x221 0x221
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x278-0x27f on isa0
unknown: <PNP0501> can't assign resources (irq)
unknown: <PNP0501> at port 0x3e8-0x3ef irq 4 on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNPb02f> failed to probe at port 0x200-0x207 on isa0
unknown: <PNPb006> failed to probe at port 0x300-0x301 irq 10 on isa0
psmcpnp0: <PS/2 mouse port> at irq 12 on isa0
psm0: current command byte:0047
psm0: failed to reset the aux device.
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0-0x9ffff,0x100000-0x3fffffff,0xe8000-0xeffff,0xf0000-0xf3fff,0xf4000-0xf7fff,0xf8000-0xfffff,0xdbc00-0xdbfff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/21.00, addr 2, iclass 3/1
ums0: 8 buttons and Z dir.
ukbd0: Logitech Logitech USB Keyboard, rev 1.10/15.00, addr 2, iclass 3/1
kbd: new array size 4
kbd1 at ukbd0
kbd1: ukbd0, generic (0), config:0x0, flags:0x1d0000
uhid0: Logitech Logitech USB Keyboard, rev 1.10/15.00, addr 2, iclass 3/1
ugen0: vendor 0x067b product 0x2303, rev 1.10/2.02, addr 2
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 2400098244 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
rr232x: no controller detected.
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting PIO4 on 963 chip
ad0: 76319MB <Seagate ST380021A 3.19> at ata0-master PIO4
ad0: 156301488 sectors [155061C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: Silicon Integrated Systems check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ad1: setting PIO4 on 963 chip
ad1: 76319MB <Seagate ST380021A 3.19> at ata0-slave PIO4
ad1: 156301488 sectors [155061C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad1
ad1: Silicon Integrated Systems check1 failed
ad1: Adaptec check1 failed
ad1: LSI (v3) check1 failed
ad1: LSI (v2) check1 failed
ad1: FreeBSD check1 failed
ata1: reiniting channel ..
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: reinit done ..
ata1: reiniting channel ..
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: reinit done ..
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire
acd0: setting PIO4 on 963 chip
acd0: <PLEXTOR DVDR PX-740A/1.02> DVDR drive at ata1 as master
acd0: read 8268KB/s (8268KB/s) write 8268KB/s (8268KB/s), 2048KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes: CDR, CDRW, DVDR, test write, burnproof
acd0: Audio: play, 2 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad8: setting PIO4 on PDC20376 chip
ad8: 114473MB <Seagate ST3120022A 3.06> at ata4-master PIO4
ad8: 234441648 sectors [232581C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad8
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ad8: FAILURE - READ timed out LBA=234441585
ad8: Promise read metadata failed
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ad8: TIMEOUT - READ retrying (1 retry left) LBA=0
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ad8: FAILURE - READ timed out LBA=234441631
ad8: Adaptec read metadata failed
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ad8: TIMEOUT - READ retrying (0 retries left) LBA=0
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ad8: FAILURE - READ timed out LBA=234441644
ad8: LSI (v3) read metadata failed
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ad8: FAILURE - READ timed out LBA=0
ad8: LSI (v2) check1 failed
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ad8: FAILURE - READ timed out LBA=234441585
ad8: FreeBSD read metadata failed
ATA PseudoRAID loaded
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata4: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ad8: setting PIO4 on PDC20376 chip
ata4: reinit done ..
ad8: TIMEOUT - READ retrying (1 retry left) LBA=0
Trying to mount root from ufs:/dev/ad1s1a
start_init: trying /sbin/init
More information about the freebsd-questions
mailing list