Siemens Santis WLAN PC Card

Csabi ethernium at yahoo.com
Sat Jul 1 13:17:09 UTC 2006


Hello,

A couple of days ago i`ve got this SIEMENS SANTIS
802.11b 11Mbps WLAN PCCard.
Since then I`m searching for a way to use it but
failed miserably... couldn`t find anything searching
the net and archives and I couldn`t interpret the
'pccard dumpcis' either so i could use with 'pccard
enabler' (maybe it`s not allways possible?)

My questions would be:
1. Did anyone used or using this type of PCCARD on
FreeBSD? If yes, how?
2. Could anyone give me some hints how to 'pccardc
enabler' this adapter using the info from the dumpcis
tuples?

I`m using FreeBSD 5.3-RELEASE i386.
--- begin pccardc dumpcis ---
Configuration data for card in slot 0
Tuple #1, code = 0x17 (Attribute memory descriptor),
length = 3
   000:  d9 01 ff
   Attribute memory device information:
       Device number 1, type Function specific, WPS =
ON
       Speed = 250nS, Memory block size = 2Kb, 1 units
Tuple #2, code = 0x1d (Other conditions for attribute
memory), length = 4
   000:  03 d9 01 ff
   (MWAIT) (3V card)
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
   000:  00 00 00 00
   PCMCIA ID = 0x0, OEM ID = 0x0
Tuple #4, code = 0x21 (Functional ID), length = 2
   000:  06 00
   Network/LAN adapter
Tuple #5, code = 0x15 (Version 1 info), length = 23
   000:  05 00 53 41 4e 54 49 53 00 57 4c 41 4e 20 50
43
   010:  20 43 61 72 64 00 ff
   Version = 5.0, Manuf = [SANTIS], card vers = [WLAN
PC Card]
Tuple #6, code = 0x1a (Configuration map), length = 6
   000:  01 02 00 08 03 ff
   Reg len = 2, config register addr = 0x800, last
config = 0x2
   Registers: XX------ 1 bytes in subtuples
Tuple #7, code = 0x1b (Configuration entry), length =
16
   000:  c1 81 9d 71 b5 1e 2e 2e 2d fc 14 45 10 b8 ff
20
   Config index = 0x1(default)
   Interface byte = 0x81 (I/O)  wait signal supported
   Vcc pwr:
       Nominal operating supply voltage: 3 x 1V, ext =
0x1e
       Max current average over 1 second: 2.5 x 100mA
       Max current average over 10 ms: 2.5 x 100mA
       Power down supply current: 2.5 x 10mA
   Wait scale Speed = 1.2 x 10 us
   Card decodes 5 address lines, limited 8/16 Bit I/O
       IRQ modes:
       IRQs:  3 4 5 7 8 9 10 11 12 13 14 15
   Max twin cards = 0
   Misc attr: (Power down supported)
Tuple #8, code = 0xff (Terminator), length = 0
2 slots found
--- end pccardc dumpcis ---

Any help or suggestion is welcome and thank you!
Best regards,
Csabi

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 


More information about the freebsd-questions mailing list