Can't get running an AIT-50 tape drive in an CL-380 server
Bernhard Fischer
bernhard.fischer at fh-stpoelten.ac.at
Fri Jun 10 07:19:35 GMT 2005
Hy,
I'm running FreeBSD 4.11 on a Compaq CL-380 Server. It has an internal Smart
Array Controller from which I successfully boot the system, and an AIT-50
tape drive which I intended to use for backups. Also the externel
RAID-Controller works fine.
Unfortunately I'm unable to get this tape drive working. I think the kernel
not even does detect it.
I put in an empty tape and try to get information:
naxos# mt status
mt: /dev/nsa0: Device not configured
I tried to find some hints on the web but it was not successful.
Does anybody have a suggestion what I could do?
thanx,
bh
Here's also the dmesg output and my kernel configuration:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.11-STABLE #1: Fri Jun 10 08:36:40 CEST 2005
lbfiser at naxos.fh-intern.ac.at:/usr/src/sys/compile/BH20050609
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel Pentium III (996.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 536854528 (524272K bytes)
avail memory = 519008256 (506844K bytes)
Preloaded elf kernel "kernel" at 0xc034d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
ida0: <Compaq Integrated Array controller> port 0x2000-0x20ff mem
0xc4000000-0xc4ffffff,0xc5000000-0xc5ffffff irq 15 at device 1.0 on pci0
ida0: drives=1 firm_rev=1.42
idad0: <Compaq Logical Drive> on ida0
idad0: 17359MB (35553120 sectors), blocksize=512
fxp0: <Intel 82559 Pro/100 Ethernet> port 0x2400-0x243f mem
0xc3e00000-0xc3efffff,0xc3fff000-0xc3ffffff irq 5 at device 2.0 on pci0
fxp0: Disabling dynamic standby mode in EEPROM
fxp0: New EEPROM ID: 0x40e0
fxp0: EEPROM checksum @ 0xff: 0x8510 -> 0x8510
fxp0: Ethernet address 00:02:a5:87:8f:e1
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <ATI Mach64-GV graphics accelerator> at 3.0
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 4.0
fxp1: <Intel 82559 Pro/100 Ethernet> port 0x2c00-0x2c3f mem
0xc3c00000-0xc3cfffff,0xc3dfd000-0xc3dfdfff irq 5 at device 5.0 on pci0
fxp1: Ethernet address 00:02:a5:3f:24:ff
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x2c40-0x2c4f at device
15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib3: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib3
sym0: <896> port 0x3000-0x30ff mem 0xc6ffc000-0xc6ffdfff,0xc6fffc00-0xc6ffffff
irq 10 at device 4.0 on pci3
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym1: <896> port 0x3400-0x34ff mem 0xc6ff8000-0xc6ff9fff,0xc6ffbc00-0xc6ffbfff
irq 11 at device 4.1 on pci3
sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0681 (System Board)> on eisa0 slot 0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xe8000-0xedfff,0xee000-0xeffff
on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ata0-slave: ATAPI identify retries exceeded
acd0: CDROM <CD-224E> at ata0-master PIO4
Waiting 15 seconds for SCSI devices to settle
pass0 at sym0 bus 0 target 2 lun 0
pass0: <Compaq CR3500 x2r-> Fixed Storage Array SCSI-2 device
pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
pass2 at sym0 bus 0 target 3 lun 0
pass2: <Compaq CR3500 x2r-> Fixed Storage Array SCSI-2 device
pass2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
da0 at sym0 bus 0 target 2 lun 2
da0: <Compaq CR3500 x2r-> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
da0: 280018MB (573476864 512 byte sectors: 255H 63S/T 35697C)
da1 at sym0 bus 0 target 3 lun 1
da1: <Compaq CR3500 x2r-> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
da1: 34720MB (71106560 512 byte sectors: 255H 63S/T 4426C)
Mounting root from ufs:/dev/idad0s2a
IP packet filtering initialized, divert disabled, rule-based forwarding
enabled, default to deny, logging disabled
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
#
http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.62 2004/12/08 22:33:10 rsm Exp
$
machine i386
#cpu I386_CPU
#cpu I486_CPU
#cpu I586_CPU
cpu I686_CPU
ident BH20050609
maxusers 0
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug
symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
#options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big
directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS
required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660
required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device ahd # AHA39320/29320 and onboard AIC79xx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
#device mpt # LSI-Logic MPT/Fusion
#device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets)
options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices when
# both sym and ncr are configured
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
#device ncv # NCR 53C500
#device nsp # Workbit Ninja SCSI-3
#device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers interfaced to the SCSI subsystem
#device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device dpt # DPT Smartcache - See LINT for options!
#device iir # Intel Integrated RAID
#device mly # Mylex AcceleRAID/eXtremeRAID
device ciss # Compaq SmartRAID 5* series
#device twa # 3ware 9000 series PATA/SATA RAID
# RAID controllers
#device aac # Adaptec FSA RAID, Dell PERC2/PERC3
device aacp # SCSI passthrough for aac (requires CAM)
device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
#device pst # Promise Supertrak SX6000
#device twe # 3ware Escalade
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
device agp # support several AGP chipsets
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power
Management
# PCCARD (PCMCIA) support
#device card
#device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
#device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device em # Intel PRO/1000 adapter Gigabit Ethernet Card
(``Wiseman'')
#device txp # 3Com 3cR990 (``Typhoon'')
#device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device pcn # AMD Am79C97x PCI 10/100 NICs
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device tx # SMC EtherPower II (83c170 ``EPIC'')
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
#device bge # Broadcom BCM570x (``Tigon III'')
# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
#device ed0 at isa? disable port 0x280 irq 10 iomem 0xd8000
#device ex
#device ep
#device fe0 at isa? disable port 0x300
# Xircom Ethernet
#device xe
# PRISM I IEEE 802.11b wireless NIC.
#device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
#device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? disable port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? disable port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? disable port 0x280 irq 10 drq 0
#device cs0 at isa? disable port 0x300
#device sn0 at isa? disable port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
#pseudo-device bpf #Berkeley packet filter
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
#device usb # USB Bus (required)
#device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
#device uscanner # Scanners
#device urio # Diamond Rio MP3 Player
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device axe # ASIX Electronics USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
# FireWire support
#device firewire # FireWire bus code
#device sbp # SCSI over FireWire (Requires scbus and da)
#device fwe # Ethernet over FireWire (non-standard!)
options QUOTA
--
____________________________________________________________________
Bernhard Fischer bernhard.fischer at fh-stpoelten.ac.at
Telekommunikation und Medien
Fachhochschule St. Pölten/St. Poelten University of Applied Sciences
Herzogenburger Straße 68 | 3100 St. Pölten | +43 (0) 2742 313228 615
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: not available
Url : http://lists.freebsd.org/pipermail/freebsd-questions/attachments/20050610/0f418282/attachment.bin
More information about the freebsd-questions
mailing list