Detect hardware changes

[Robert Marella]

On Mon, 12 Dec 2005 08:27:06 -0600
"Keith Bottner" <keith at barkinglizards.com> wrote:

> > 
> > On Thu, Dec 08, 2005 at 12:02:25PM -0900, Peter Giessel wrote:
> > > On 12/8/2005 11:51, Keith Bottner seems to have typed:
> > > > skc0 at pci2:9:0:  class=0x020000 card=0x00241737 chip=0x10321737 
> > > > rev=0x10 hdr=0x00
> > > >     vendor   = 'Linksys'
> > > >     device   = 'EG1032 Gigabit Ethernet'
> > > >     class    = network
> > > >     subclass = ethernet
> > > 

> 
> Ifconfig does not show skc0 but here is the output for completeness:
> 
> xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> 	options=9<RXCSUM,VLAN_MTU>
> 	inet 192.168.1.217 netmask 0xffffff00 broadcast 192.168.1.255
> 	inet6 fe80::2b0:d0ff:fe16:3d30%xl0 prefixlen 64 scopeid 0x1 
> 	ether 00:b0:d0:16:3d:30
> 	media: Ethernet autoselect (100baseTX <full-duplex>)
> 	status: active
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> 	inet 127.0.0.1 netmask 0xff000000 
> 	inet6 ::1 prefixlen 128 
> 	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 
> 
> And rc.conf is:
> 
> defaultrouter="192.168.1.1"
> hostname="gsdev.bltmobile.com"
> ifconfig_xl0="inet 192.168.1.217  netmask 255.255.255.0"
> ifconfig_skc0="inet 10.0.130.204  netmask 255.255.255.0"
> linux_enable="YES"
> moused_enable="YES"
> sshd_enable="YES"
> usbd_enable="YES"
> postgresql_enable="YES"
> 
> Anything else that I can send that will help?
> 
> Keith

Hello Keith

I'm not sure I can be of any help. I have an older Asus board (2years)
that uses an onboard sk card. Here is the output from my machine

skc0 at pci2:5:0:  class=0x020000 card=0x80eb1043 chip=0x170010b7 rev=0x12
hdr=0x00 vendor   = '3COM Corp, Networking Division'
    device   = '3C940 and 3C2000 Gigabit Ethernet PCI CODEC?'
    class    = network
    subclass = ethernet

Mine is 3COM while yours is Linksys.

[robert at p4] ~> grep sk /var/run/dmesg.boot
skc0: <3Com 3C940 Gigabit Ethernet> port 0xd800-0xd8ff mem
0xfeafc000-0xfeafffff irq 22 at device 5.0 on pci2 skc0: 3Com Gigabit
LOM (3C940) rev. (0x1) sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: Ethernet address: 00:0c:6e:91:de:a6
miibus0: <MII bus> on sk0

The mii bus is shown here and unless you have removed it from your
kernel it would be automatic.

From rc.conf

defaultrouter="10.0.0.1"
hostname="p4.konav201.local"
ifconfig_sk0="inet 10.0.0.103  media 100baseTX mediaopt full-duplex
netmask 255.255.255.0"

Notice that it is sk0 _not_ skc0. AFAIK this is not your problem but it
should be changed in your rc.conf file. Except for an occasional
"watchdog" it is working fine.

I google'd for your error "rid 0x10 is ioport" but didn't see any
solutions. There was some reference to ACPI so it might be something to
try. 

BTW I am running 6 Stable.

I hope this helps. Good luck
Robert