Re: Toshiba Portégé 4000 laptop

[Laurent Debacker]

With FreeSBIE 1.1 (based on FreeBSD 5.3), it says:
acd0: TIMEOUT - READ_BIG retrying (2 retries left)
acd0: TIMEOUT - READ_BIG timed out
Then it stop/freezes.
If I press the power button, it says "acpi: suspend request ignored
(not ready yet)."

Thanks.

On 4/23/05, Laurent Debacker <debackerl at gmail.com> wrote:
> I tried 5.4-RC3 with no ACPI, safe mode, and DEBUG mode, without
> success. DEBUG doesn't repport anything.
> 
> 5.3 also crashes in safe mode, and no ACPI, freezes after "pci0: <PCI
> bus> on pcib0".
> 
> dmesg on 4.11 reports:
> ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem
> 0xf7eff000-0xf7efffff irq 11 at device 2.0 on pci0.
> You can see full report below.
> 
> Thank you for your help ;)
> Laurent.
> 
> Here are drivers loaded by 4.11 as reported by dmesg:
> md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03edc14
> md1: Malloc disk
> Using $PIR table, 9 entries at 0xc00f01d0
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pcib1: <Acerlabs M5247 PCI-PCI(AGP Supported) bridge> at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> pci1: <Trident model 8820 VGA-compatible display device> at 0.0 irq 11
> ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem
> 0xf7eff000-0xf7efffff irq 11 at device 2.0 on pci0
> usb0: OHCI version 1.0, legacy support
> usb0: SMM does not respond, resetting
> usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 4 ports with 4 removable, self powered
> atapci0: <AcerLabs Aladin ATA66 controller> port 0xeff0-0xefff at
> device 4.0 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> pci0: <unknown card> (vendor=0x10b9, dev=0x5451) at 6.0
> isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> chip1: <AcerLabs M15x3 Power Management Unit> at device 8.0 on pci0
> fxp0: <Intel 82559 Pro/100 Ethernet> port 0xeec0-0xeeff mem
> 0xf7d00000-0xf7dfffff,0xf7efe000-0xf7efefff irq 11 at device 10.0 on
> pci0
> fxp0: Ethernet address 00:00:39:a7:a0:b4
> inphy0: <i82555 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> pci_cfgintr_linked: linked (3) to hard-routed irq 11
> pci_cfgintr: 0:16 INTA routed to irq11
> pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 16.0 on pci0
> pcic0: PCI Memory allocated: 0x88000000
> pcic0: TI12XX PCI Config Reg: [pwr save][pci only]
> pccard0: <PC Card 16-bit bus (classic)> on pcic0
> pci_cfgintr_linked: linked (1) to hard-routed irq 11
> pci_cfgintr: 0:17 INTA routed to irq11
> pcic1: <Toshiba ToPIC100 PCI-CardBus Bridge> irq 11 at device 17.0 on pci0
> pcic1: PCI Memory allocated: 0x88001000
> pccard1: <PC Card 16-bit bus (classic)> on pcic1
> pci_cfgintr_linked: linked (2) to hard-routed irq 11
> pci_cfgintr: 0:17 INTB routed to irq11
> pcic2: <Toshiba ToPIC100 PCI-CardBus Bridge> irq 11 at device 17.1 on pci0
> pcic2: PCI Memory allocated: 0x88002000
> pccard2: <PC Card 16-bit bus (classic)> on pcic2
> pci0: <unknown card> (vendor=0x1179, dev=0x0805) at 18.0
> orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xe0000-0xeffff on isa0
> pmtimer0 on isa0
> fdc0: ready for input in output
> fdc0: cmd 3 failed at out byte 1 of 3
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model IntelliMouse, device ID 3
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: configured irq 3 not in bitmap of probed irqs 0
> ppc0: parallel port not found.
> pccard: card inserted, slot0
> pccard: card removed, slot0
> ad0: 16077MB <IC25N020ATCS04-0> [38760/16/63] at ata0-master UDMA66
> acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2502> at ata1-master PIO4
> 
> On 4/23/05, Kevin Kinsey <kdk at daleco.biz> wrote:
> > Laurent Debacker wrote:
> >
> > >Hello,
> > >
> > >Both FreeBSD 5.3 and 5.4-RC3 freeze during the boot of the kernel. It
> > >detects my CPU, RAM, some ACPI stuffs.. I noticed
> > >pci1: <display, VGA> at device 0.0 (no driver attached).
> > >I don't know if it's ok.
> > >At the end, it says ohci0: [GIANT-LOCKED]
> > >then usb0: OHCI version 1.0, legacy support,
> > >then nothing.
> > >
> > >FreeBSD 4.11 boots well. However I don't want FreeBSD 4.11 ;)
> > >
> > >Any idea?
> > >
> > >Thank you,
> > >Laurent Debacker.
> > >
> > >
> >
> > What does the 4.11 dmesg say about the ochi device?
> >
> > Can you boot safe mode on 5.X?  Have you tried booting
> > with ACPI disabled?
> >
> > HTH,
> >
> > KDK
> >
> >
>