RAID 1 in HP NetServer LC 2000
Muhammad Reza
reza at mra.co.id
Mon Oct 11 06:18:00 PDT 2004
Ok.. vinum then..
but i have error when applied this vinum.conf
drive drive1 device /dev/da0s1e
drive drive2 device /dev/da1s1e
volume usr setupstate
plex org concat
sd length 13887091s drive drive1
plex org concat
sd length 13887091s drive drive2
volume var setupstate
plex org concat
sd length 0 drive drive1
plex org concat
sd length 0 drive drive2
mail# vinum
vinum -> create -f /etc/vinum.conf
2: drive drive2 device /dev/da1s1e
/*** 2 : Invalid argument*/
1 drives:
D drive1 State: up Device /dev/da0s1e Avail:
0/16488 MB (0%)
D drive2 State: referenced Device /dev/da1s1e
Avail: 0/0 MB
2 volumes:
V usr State: up Plexes: 2 Size: 6780 MB
V var State: up Plexes: 2 Size: 9707 MB
4 plexes:
P usr.p0 C State: up Subdisks: 1 Size: 6780 MB
P usr.p1 C State: up Subdisks: 1 Size: 6780 MB
P var.p0 C State: up Subdisks: 1 Size: 9707 MB
P var.p1 C State: up Subdisks: 1 Size: 0 B
4 subdisks:
S usr.p0.s0 State: up PO: 0 B Size: 6780 MB
S usr.p1.s0 State: up PO: 0 B Size: 6780 MB
S var.p0.s0 State: up PO: 0 B Size: 9707 MB
S var.p1.s0 State: up PO: 0 B Size: 0 B
which argumen is invalid ? i use 4.10 ..
please help me...
regards
reza
>Am Freitag, 8. Oktober 2004 15:47 schrieb Muhammad Reza:
>
>
>>Dear All,
>>Howto setup RAID 1 in HP NetServer LC 2000 ? I have 2 Seagate HDD that
>>want to be mirror 1:1,
>>Can i do that from Symbios software or tool from my FreeBSD 4.10 ?
>>
>>
>
>With 4.10 you have the choice of vinum and ccd, in 5.3 you also have gmirror
>for RAID1. See the man pages for details, ccd is quiet easy, vinum is a bit
>more complex but more flexible too.
>
>-Harry
>
>
>
>>regards
>>reza
>>---snip---
>>sym0: <896> port 0x2000-0x20ff mem
>>0xfd000000-0xfd001fff,0xfd002000-0xfd0023ff irq 11 at device 6.0 on pci3
>>sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
>>sym0: open drain IRQ line driver, using on-chip SRAM
>>sym0: using LOAD/STORE-based firmware.
>>sym0: handling phase mismatch from SCRIPTS.
>>sym1: <896> port 0x2400-0x24ff mem
>>0xfd004000-0xfd005fff,0xfd002400-0xfd0027ff irq 5 at device 6.1 on pci3
>>sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
>>sym1: open drain IRQ line driver, using on-chip SRAM
>>sym1: using LOAD/STORE-based firmware.
>>sym1: handling phase mismatch from SCRIPTS.
>>---snap---
>>..
>>..
>>--snip--
>>da0 at sym1 bus 0 target 0 lun 0
>>da0: <SEAGATE ST318405LW 5063> Fixed Direct Access SCSI-3 device
>>da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
>>Enabled
>>da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
>>da1 at sym1 bus 0 target 1 lun 0
>>da1: <SEAGATE ST318405LW 5063> Fixed Direct Access SCSI-3 device
>>da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
>>Enabled
>>da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
>>---snap---
>>
>>
>>
>>
>>
>>_______________________________________________
>>freebsd-questions at freebsd.org mailing list
>>http://lists.freebsd.org/mailman/listinfo/freebsd-questions
>>To unsubscribe, send any mail to
>>"freebsd-questions-unsubscribe at freebsd.org
>>
>"
>
>
More information about the freebsd-questions
mailing list