Compaq Prolian CL380 & Array Controller CR3500 Problems: Any
Suggestions Please
Dew Ediho
eccmqv at gmail.com
Wed Jul 21 09:10:35 PDT 2004
Dear List members,
I run freebsd 4.10 on a proliant cl380 server. I split the nodes and
do not use them as a clustered server.
I created a /Data dir for the primary node using the accompnying SCSI
array (RAID 5) with controller CR3500.
I configured the controller and created the array using Compaq Array
Utility software .
The machine ran perfectly for more than 60 days until a power outage
resulted into the box not booting up properly.
I was able to get the server to boot but accessing the SCSI array is impossible.
The following are logs from the system
The machine runs and but I can not use the /Data directory.
The screen shot of the CR3500 configuration has been convinently located at
http://www.morgan.edu/newtemp/ErrorReport.pdf
mailed# df
Filesystem 1K-blocks Used Avail Capacity Mounted on
/dev/idad0s1a 387006 35912 320134 10% /
/dev/da0s1e 70012386 134 64411262 0% /Data
/dev/idad0s1f 2064302 20 1899138 0% /tmp
/dev/idad0s1g 2675182 1026494 1434674 42% /usr
/dev/idad0s1e 2064302 23986 1875172 1% /var
procfs 4 4 0 100% /proc
/Data directory is on the SCSI array. Others are on the node hard drive.
mailed# dmesg
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.10-RELEASE #0: Tue May 25 22:47:12 GMT 2004
root at perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel Pentium III (797.48-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 671072256 (655344K bytes)
avail memory = 646737920 (631580K bytes)
Preloaded elf kernel "kernel" at 0xc0551000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
ida0: <Compaq Integrated Array controller> port 0x2000-0x20ff mem
0xc4000000-0xc4ffffff,0xc5000000-0xc5ffffff irq 15 at device 1.0 on
pci0
ida0: drives=1 firm_rev=1.42
idad0: <Compaq Logical Drive> on ida0
idad0: 8670MB (17756160 sectors), blocksize=512
fxp0: <Intel 82559 Pro/100 Ethernet> port 0x2400-0x243f mem
0xc3e00000-0xc3efffff,0xc3fff000-0xc3ffffff irq 5 at device 2.0 on
pci0
fxp0: Disabling dynamic standby mode in EEPROM
fxp0: New EEPROM ID: 0x40a0
fxp0: EEPROM checksum @ 0xff: 0x6bc5 -> 0x6bc5
fxp0: Ethernet address 00:02:a5:09:31:ed
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <ATI Mach64-GV graphics accelerator> at 3.0
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 4.0
fxp1: <Intel 82559 Pro/100 Ethernet> port 0x2c00-0x2c3f mem
0xc3c00000-0xc3cfffff,0xc3dfd000-0xc3dfdfff irq 5 at device 5.0 on
pci0
fxp1: Ethernet address 00:50:8b:b8:2f:33
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x2c40-0x2c4f at
device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib3: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib3
sym0: <896> port 0x3000-0x30ff mem
0xc6ffc000-0xc6ffdfff,0xc6fffc00-0xc6ffffff irq 10 at device 4.0 on
pci3
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym1: <896> port 0x3400-0x34ff mem
0xc6ff8000-0xc6ff9fff,0xc6ffbc00-0xc6ffbfff irq 11 at device 4.1 on
pci3
sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0681 (System Board)> on eisa0 slot 0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xe8000-0xedfff,0xee000-0xeffff
on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ata0-slave: ATAPI identify retries exceeded
acd0: CDROM <CD-224E> at ata0-master PIO4
Waiting 15 seconds for SCSI devices to settle
pass0 at sym0 bus 0 target 9 lun 0
pass0: <Compaq CR3500 x2q> Fixed Storage Array SCSI-2 device
pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged
Queueing Enabled
pass2 at sym0 bus 0 target 10 lun 0
pass2: <Compaq CR3500 x2q> Fixed Storage Array SCSI-2 device
pass2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged
Queueing Enabled
da0 at sym0 bus 0 target 9 lun 1
da0: <Compaq CR3500 x2q> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 69454MB (142241792 512 byte sectors: 255H 63S/T 8854C)
Mounting root from ufs:/dev/idad0s1a
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: unexpected disconnect
sym0:9:control msgout: 81 22 47 d.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: unexpected disconnect
sym0:9:control msgout: 81 22 61 d.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0: SCSI phase error fixup: CCB already dequeued.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
More information about the freebsd-questions
mailing list