DMA limited to UDMA33, non-ATA66 cable or device
Rob
rob at debank.tv
Fri Jul 25 03:53:59 PDT 2003
Ugo Bellavance wrote:
>>>They're brand new cables, from promise, and I don't have this problem
>
> under linux (I get over 40 MB/s transfer rate with hdparm). However, I will
> try other cables eventually. If anyone has another idea, please let me
> know. Thanks,
> Ugo>>
>
> --
> Try getting new cables. I have had a similar problem caused by bad cables
> before.
>
> On Thu, 24 Jul 2003 22:57:48 -0400 (EDT)
> Ugo Bellavance <iolubik at yahoo.ca> wrote:
>
>
>>Hi,
>>
>>--System
>>FreeBSD 4.8 release
>>It is a kernel that I recompiled only to enable SMP.
>>The same error comes with the generic stock generic
>>Kernel.
>>It is a dual Athlon MP 1800+ on a tyan MB. The Raid
>>card is a TX-2000 with 2 Hot swap superswap enclosure.
>> The only other IDE device, the cd-rom is on the IDE
>>controller on the motherboard. The raid is a RAID1
>>with 2 Western Digital 80 Gb, 8 Mb cache, 7200rpm,
>>each of them is ont a separate channel. I checked the
>>cable and they are connected on the right side. I
>>even tried to put them the other way around and I get
>>the same error message.
>>
>>--Problem: FreeBSD only puts my drive in udma33 while
>>the Motherboard, cables, enclosures and drives support
>>udma100. I don't know if it is a bogus error, because
>>I don't know how to test it (like hdparm in linux).
>>
>>--Other data:
>>
>>output from dmesg
>>
>>atapci1: <Promise TX2 ATA133 controller> port
>>0x1010-0x101f,0x1024-0x1027,0x1028-0x102f,0x1030-0x1033,0x1038-0x103f
>>mem 0xf0000000-0xf000ffff irq 2 at device 8.0 on pci0
>>ad4: DMA limited to UDMA33, non-ATA66 cable or device
>>ad6: DMA limited to UDMA33, non-ATA66 cable or device
>>ar0: 1907348MB <ATA RAID1 array> [65535/255/63]
>>status: READY subdisks:
>> 0 READY ad4: 76319MB <WDC WD800JB-00CRA1>
>>[155061/16/63] at ata2-master UDMA33
>> ad4: SuperSwap enclosure [FAN:4218rpm
>>TEMP:28.0C 5.022V 12.078V]
>> 1 READY ad6: 76319MB <WDC WD800JB-00CRA1>
>>[155061/16/63] at ata3-master UDMA33
>> ad6: SuperSwap enclosure [FAN:4166rpm
>>TEMP:28.0C 4.941V 11.895V]
>>Jul 24 21:16:08 bibi /kernel: acd0: CDROM <HL-DT-ST
>>CD-ROM GCR-8520B> at ata1-master PIO4
>>
>>output of atacontrol list
>>
>> atacontrol list
>>ATA channel 0:
>> Master: no device present
>> Slave: no device present
>>ATA channel 1:
>> Master: acd0 <HL-DT-ST CD-ROM GCR-8520B/1.00>
>>ATA/ATAPI rev 0
>> Slave: no device present
>>ATA channel 2:
>> Master: ad4 <WDC WD800JB-00CRA1/17.07W17>
>>ATA/ATAPI rev 5
>> Slave: no device present
>>ATA channel 3:
>> Master: ad6 <WDC WD800JB-00CRA1/17.07W17>
>>ATA/ATAPI rev 5
>> Slave: no device present
>>
>>Nothing interesting in /var/log/messages
>>
>>Other logs can be provided upon request. I just don't
>>want to make the post too long.
>>
>>Thanks for your help.
>>
>>Ugo Bellavance
>
Try man 8 atacontrol
Especialy the 'mode' command
Rob Evers
More information about the freebsd-questions
mailing list