pcm on 5.1

[Kenneth Culver]

On Thursday, July 3, 2003, at 07:58  PM, Laszlo Vagner wrote:

> I just updated to 5.1-r and was wondering how to add soundcard support  
> to the
> kernel.?
>
> in 4.8 i just added 'device pcm' in my kernel config and recompiled  
> but 5.1 is different
> and i dont want to do something to mess things up.
>
> dmesg follows.
>

Just do what you've always done. Add device pcm to your kernel.

Ken

>
> amd2000# dmesg
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,  
> 1994
>        The Regents of the University of California. All rights  
> reserved.
> FreeBSD 5.1-RELEASE #0: Thu Jun  5 02:55:42 GMT 2003
>    root at wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc06d4000.
> Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06d4244.
> Timecounter "i8254"  frequency 1193182 Hz
> Timecounter "TSC"  frequency 1666738222 Hz
> CPU: AMD Athlon(TM) XP 2000+ (1666.74-MHz 686-class CPU)
>  Origin = "AuthenticAMD"  Id = 0x662  Stepping = 2
>   
> Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE 
> ,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
>  AMD Features=0xc0400000<AMIE,DSP,3DNow!>
> real memory  = 536854528 (511 MB)
> avail memory = 514064384 (490 MB)
> Pentium Pro MTRR support enabled
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> acpi0: <ASUS   A7V8X   > on motherboard
> pcibios: BIOS version 2.10
> Using $PIR table, 12 entries at 0xc00f1cd0
> acpi0: power button is handled as a fixed feature programming model.
> Timecounter "ACPI-fast"  frequency 3579545 Hz
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
> acpi_cpu0: <CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> agp0: <VIA Generic host to PCI bridge> mem 0xf8000000-0xfbffffff at  
> device 0.0 on pci0
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> pci1: <display, VGA> at device 0.0 (no driver attached)
> fwohci0: <VIA VT6306> port 0xd800-0xd87f mem 0xed800000-0xed8007ff irq  
> 5 at device 7.0 on pci0
> fwohci0: OHCI version 1.0 (ROM=1)
> fwohci0: No. of Isochronous channel is 8.
> fwohci0: EUI64 00:e0:18:00:00:08:81:a6
> fwohci0: Phy 1394a available S400, 3 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> if_fwe0: <Ethernet over FireWire> on firewire0
> if_fwe0: Fake Ethernet address: 02:e0:18:08:81:a6
> sbp0: <SBP2/SCSI over firewire> on firewire0
> fwohci0: Initiate bus reset
> atapci0: <Promise PDC20376 SATA150 controller> port  
> 0xb800-0xb87f,0xd000-0xd00f,0xd400-0xd43f mem  
> 0xec800000-0xec81ffff,0xed000000-0xed000fff irq 5 at device 8.0 on > pci0
> ata2: at 0xed000000 on atapci0
> ata3: at 0xed000000 on atapci0
> ata4: at 0xed000000 on atapci0
> pci0: <network, ethernet> at device 9.0 (no driver attached)
> ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0xb400-0xb4ff mem  
> 0xeb800000-0xeb800fff irq 9 at device 12.0 on pci0
> aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
> xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xb000-0xb03f irq 11 at  
> device 13.0 on pci0
> xl0: Ethernet address: 00:10:4b:95:5f:63
> miibus0: <MII bus> on xl0
> nsphy0: <DP83840 10/100 media interface> on miibus0
> nsphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> xl1: <3Com 3c905-TX Fast Etherlink XL> port 0xa800-0xa83f irq 5 at  
> device 14.0 on pci0
> xl1: Ethernet address: 00:60:97:7b:22:56
> miibus1: <MII bus> on xl1
> nsphy1: <DP83840 10/100 media interface> on miibus1
> nsphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> uhci0: <VIA 83C572 USB controller> port 0xa400-0xa41f irq 9 at device  
> 16.0 on pci0
> usb0: <VIA 83C572 USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhub0: port error, restarting port 1
> uhub0: port error, giving up port 1
> umass0: Shuttle Technology Inc. eUSCSI Bridge Ver 1.11, rev 1.00/1.00,  
> addr 2
> umass0: Get Max Lun not supported (STALLED)
> uhub0: port error, restarting port 2
> uhub0: port error, giving up port 2
> uhci1: <VIA 83C572 USB controller> port 0xa000-0xa01f irq 9 at device  
> 16.1 on pci0
> usb1: <VIA 83C572 USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <VIA 83C572 USB controller> port 0x9800-0x981f irq 9 at device  
> 16.2 on pci0
> usb2: <VIA 83C572 USB controller> on uhci2
> usb2: USB revision 1.0
> uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> pci0: <serial bus, USB> at device 16.3 (no driver attached)
> isab0: <PCI-ISA bridge> at device 17.0 on pci0
> isa0: <ISA bus> on isab0
> atapci1: <VIA 8235 UDMA133 controller> port 0x9400-0x940f at device  
> 17.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci1
> ata1: at 0x170 irq 15 on atapci1
> pci0: <multimedia, audio> at device 17.5 (no driver attached)
> fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port  
> 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/9 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> sio0 port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1 port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model IntelliMouse, device ID 3
> pmtimer0 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on  
> isa0
> Timecounters tick every 10.000 msec
> fwohci0: BUS reset
> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> firewire0: bus manager 0 (me)
> ad0: 114473MB <ST3120023A> [232581/16/63] at ata0-master UDMA100
> acd0: CD-RW <LITE-ON LTR-52246S> at ata1-master PIO4
> acd1: CDROM <CD-ROM 36X/AKU> at ata1-slave PIO4
> Waiting 15 seconds for SCSI devices to settle
> da0 at ahc0 bus 0 target 0 lun 0
> da0: <SEAGATE ST318451LW 0002> Fixed Direct Access SCSI-3 device
> da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged  
> Queueing Enabled
> da0: 17501MB (35843671 512 byte sectors: 255H 63S/T 2231C)
> da1 at umass-sim0 bus 0 target 0 lun 0
> da1: <CWS ORB2 -SE U ID 0 D29> Removable Direct Access SCSI-2 device
> da1: 1.000MB/s transfers
> da1: 2103MB (4307184 512 byte sectors: 255H 63S/T 268C)
> Mounting root from ufs:/dev/da0s1a
> dragon_saver: the console does not support M_VGA_CG320
> module_register_init: MOD_LOAD (dragon_saver, 0xc1534c70, 0) error 19
> cd9660: RockRidge Extension
> umass0: Phase Error, residue = 0
> (da1:umass-sim0:0:0:0): Synchronize cache failed, status == 0x4, scsi  
> status == 0x0
> amd2000#
>
>
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to  
> "freebsd-questions-unsubscribe at freebsd.org"
>