Install SCSI CD-R

[Jason Cribbins]

I have had no luck at all finding the correct procedure to install a SCSI CD-R 
under FreeBSD.  I am uses an AHA-1701 SCSI controller but I believe this is 
not being seen at all by the hardware probe...although I may not even know 
what I am looking for.

I Am running FreeBSD 5.0-RELEASAE installed from the FTP site about 2 months 
ago so everything is pretty recent versions of everything.  The only reason I 
am runing 5.0-RELEASE is because it seems to be the only one that supports my 
SB Live sound card.

Anyhow below is the dmesg.today.  Anyone see if my card is even being 
reconized by FreeBSD...and if not is there an driver I can load before the 
kernel boots much like then one I use for my sb live?

THanks
Jason Cribbins

12:53pm butters:/var/log # cat dmesg.today
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE #0: Thu Jan 16 22:16:53 GMT 2003
    root at hollin.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc064e000.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc064e0a8.
Preloaded elf module "/boot/kernel/snd_emu10k1.ko" at 0xc064e154.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 451024572 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (451.02-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x673  Stepping = 3
  
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory  = 268435456 (256 MB)
avail memory = 252944384 (241 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using $PIR table, 8 entries at 0xc00fded0
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffffff at 
device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 2.1 on 
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd000-0xd01f irq 11 at 
device 2.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Cypress Sem PS2/USB Browser Combo Mouse, rev 1.00/0.10, addr 2, iclass 
3/1
ums0: 5 buttons and Z dir.
pci0: <bridge, PCI-unknown> at device 2.3 (no driver attached)
pci0: <display, VGA> at device 13.0 (no driver attached)
dc0: <82c169 PNIC 10/100BaseTX> port 0xd800-0xd8ff mem 0xee010000-0xee0100ff 
irq 12 at device 15.0 on pci0
dc0: Ethernet address: 00:a0:cc:28:41:fa
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative EMU10K1> port 0xdc00-0xdc1f irq 11 at device 16.0 on pci0
orm0: <Option ROMs> at iomem 0xcc000-0xcdfff,0xc0000-0xc8fff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <OKI DATA CORP OKIPAGE 10e> PJL,PCLXL,PCL,EPSONFX,IBMPPR
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0a03> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
Timecounters tick every 10.000 msec
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 19541MB <Maxtor 2B020H1> [39703/16/63] at ata0-master UDMA33
acd0: CDROM <ATAPI CDROM> at ata0-slave PIO4
Mounting root from ufs:/dev/ad0s1a
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE #0: Thu Jan 16 22:16:53 GMT 2003
    root at hollin.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc064e000.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc064e0a8.
Preloaded elf module "/boot/kernel/snd_emu10k1.ko" at 0xc064e154.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 451024572 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (451.02-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x673  Stepping = 3
  
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory  = 268435456 (256 MB)
avail memory = 252944384 (241 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using $PIR table, 8 entries at 0xc00fded0
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffffff at 
device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 2.1 on 
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd000-0xd01f irq 11 at 
device 2.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Cypress Sem PS2/USB Browser Combo Mouse, rev 1.00/0.10, addr 2, iclass 
3/1
ums0: 5 buttons and Z dir.
pci0: <bridge, PCI-unknown> at device 2.3 (no driver attached)
pci0: <display, VGA> at device 13.0 (no driver attached)
dc0: <82c169 PNIC 10/100BaseTX> port 0xd800-0xd8ff mem 0xee010000-0xee0100ff 
irq 12 at device 15.0 on pci0
dc0: Ethernet address: 00:a0:cc:28:41:fa
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative EMU10K1> port 0xdc00-0xdc1f irq 11 at device 16.0 on pci0
orm0: <Option ROMs> at iomem 0xcc000-0xcdfff,0xc0000-0xc8fff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <OKI DATA CORP OKIPAGE 10e> PJL,PCLXL,PCL,EPSONFX,IBMPPR
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0a03> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
Timecounters tick every 10.000 msec
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 19541MB <Maxtor 2B020H1> [39703/16/63] at ata0-master UDMA33
acd0: CDROM <ATAPI CDROM> at ata0-slave PIO4
Mounting root from ufs:/dev/ad0s1a
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
12:53pm butters:/var/log #