Reboot after start pf on ALIX board
Espartano
espartano.mail at gmail.com
Mon Jun 27 21:59:17 UTC 2011
Hi People I'm having a problem with my Alix board model 2d3
(http://pcengines.ch/alix2d3.htm) , Yesterday I compiled and installed
NanoBSD into my alix board using FreeBSD 8.2 RELEASE, today when i
tried to configure network interfaces and pf firewall to do nat over
the wireless network I got this error and the sistem was rebooted:
zrouter# /etc/rc.d/pf onestart
Enabling pf
Fatal trap 12: page fault while in kernel mode
cpuid = 0; apic id = 00
fault virtual address = 0x18
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc07c50ce
stack pointer = 0x28:0xcd1f8a18
frame pointer = 0x28:0xcd1f8a38
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 1755 (pfctl)
trap number = 12
panic: page fault
cpuid = 0
KDB: stack backtrace:
#0 0xc072c5b7 at kdb_backtrace+0x47
#1 0xc06fd457 at panic+0x117
#2 0xc08f9003 at trap_fatal+0x323
#3 0xc08f9280 at trap_pfault+0x270
#4 0xc08f97c5 at trap+0x465
#5 0xc08e037c at calltrap+0x6
#6 0xc04d8a25 at pfioctl+0x965
#7 0xc0681c8a at devfs_ioctl_f+0x10a
#8 0xc073b6b0 at kern_ioctl+0x280
#9 0xc073b824 at ioctl+0x134
#10 0xc07382e9 at syscallenter+0x329
#11 0xc08f92d4 at syscall+0x34
#12 0xc08e03e1 at Xint0x80_syscall+0x21
Uptime: 4m6s
Cannot dump. Device not defined or unavailable.
Automatic reboot in 15 seconds - press a key on the console to abort
#####################################
This is the output from ifconfig command:
zrouter# ifconfig
vr0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8280b<RXCSUM,TXCSUM,VLAN_MTU,WOL_UCAST,WOL_MAGIC,LINKSTATE>
ether 00:0d:b9:12:6f:00
media: Ethernet autoselect (none)
status: no carrier
vr1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8280b<RXCSUM,TXCSUM,VLAN_MTU,WOL_UCAST,WOL_MAGIC,LINKSTATE>
ether 00:0d:b9:12:6f:01
inet 192.168.100.1 netmask 0xffffff00 broadcast 192.168.100.255
media: Ethernet autoselect (none)
status: no carrier
vr2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8280b<RXCSUM,TXCSUM,VLAN_MTU,WOL_UCAST,WOL_MAGIC,LINKSTATE>
ether 00:0d:b9:12:6f:02
inet 10.0.0.1 netmask 0xffffff00 broadcast 10.0.0.255
media: Ethernet autoselect (none)
status: no carrier
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether 00:0b:6b:db:0d:70
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
status: running
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet 127.0.0.1 netmask 0xff000000
pfsync0: flags=0<> metric 0 mtu 1460
syncpeer: 224.0.0.240 maxupd: 128
pflog0: flags=0<> metric 0 mtu 33200
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:0b:6b:db:0d:70
inet 192.168.1.105 netmask 0xffffff00 broadcast 255.255.255.255
media: IEEE 802.11 Wireless Ethernet OFDM/24Mbps mode 11g
status: associated
ssid SIPS channel 6 (2437 MHz 11g) bssid 00:27:19:de:26:26
country US ecm authmode WPA2/802.11i privacy ON deftxkey UNDEF
TKIP 2:128-bit txpower 23.5 bmiss 7 scanvalid 450 bgscan
bgscanintvl 300 bgscanidle 250 roam:rssi 7 roam:rate 5 protmode CTS
wme burst roaming MANUAL
wlan1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:0b:6b:db:0d:70
inet 172.16.0.1 netmask 0xffffff00 broadcast 172.16.0.255
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
status: running
ssid SIPS2 channel 6 (2437 MHz 11g) bssid 00:0b:6b:db:0d:70
country US ecm authmode WPA privacy MIXED deftxkey 2 TKIP 2:128-bit
txpower 23.5 scanvalid 60 protmode CTS wme burst dtimperiod 1 -dfs
zrouter#
#####################################
The pf firewall rules are very simple and pf -vnf wasn't complain for it:
zrouter# cat /etc/pf.conf
if_lan0=vr0
if_lan1=vr1
if_lan2=vr2
if_wifi_0=wlan0
if_wifi_1=wlan1
nat on $if_wifi_0 from any -> ($if_wifi_0)
pass in
pass out
zrouter#
zrouter# pfctl -vnf /etc/pf.conf
if_lan0 = "vr0"
if_lan1 = "vr1"
if_lan2 = "vr2"
if_wifi_0 = "wlan0"
if_wifi_1 = "wlan1"
nat on wlan0 all -> (wlan0) round-robin
pass in all flags S/SA keep state
pass out all flags S/SA keep state
zrouter#
####################################
If it is helpfull in order to figure out what was happened here is the
output messages from the boot process:
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-RELEASE #0: Sun Jun 26 06:05:14 CDT 2011
root@:/usr/obj/nanobsd.ZROUTER/usr/src/sys/ZROUTER i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by AMD PCS (498.05-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x5a2 Family = 5 Model = a Stepping = 2
Features=0x88a93d<FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CLFLUSH,MMX>
AMD Features=0xc0400000<MMX+,3DNow!+,3DNow!>
real memory = 268435456 (256 MB)
avail memory = 252387328 (240 MB)
pnpbios: Bad PnP BIOS data checksum
WARNING: VIMAGE (virtualized network stack) is a highly experimental feature.
K6-family MTRR support enabled (2 registers)
kbd0 at kbdmux0
ACPI Error: A valid RSDP was not found (20101013/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: <encrypt/decrypt, entertainment crypto> at device 1.2 (no driver attached)
vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0x1000-0x10ff mem
0xe0000000-0xe00000ff irq 10 at device 9.0 on pci0
vr0: Quirks: 0x2
vr0: Revision: 0x96
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: Ethernet address: 00:0d:b9:12:6f:00
vr0: [ITHREAD]
vr1: <VIA VT6105M Rhine III 10/100BaseTX> port 0x1400-0x14ff mem
0xe0040000-0xe00400ff irq 11 at device 10.0 on pci0
vr1: Quirks: 0x2
vr1: Revision: 0x96
miibus1: <MII bus> on vr1
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr1: Ethernet address: 00:0d:b9:12:6f:01
vr1: [ITHREAD]
vr2: <VIA VT6105M Rhine III 10/100BaseTX> port 0x1800-0x18ff mem
0xe0080000-0xe00800ff irq 12 at device 11.0 on pci0
vr2: Quirks: 0x2
vr2: Revision: 0x96
miibus2: <MII bus> on vr2
ukphy2: <Generic IEEE 802.3u media interface> PHY 1 on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr2: Ethernet address: 00:0d:b9:12:6f:02
vr2: [ITHREAD]
ath0: <Atheros 5212> mem 0xe00c0000-0xe00cffff irq 9 at device 12.0 on pci0
ath0: [ITHREAD]
ath0: AR5212 mac 5.9 RF5112 phy 4.3
isab0: <PCI-ISA bridge> port
0x6000-0x6007,0x6100-0x61ff,0x6200-0x623f,0x9d00-0x9d7f,0x9c00-0x9c3f
at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD CS5536 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 15.2 on
pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <multimedia, audio> at device 15.3 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xefffe000-0xefffefff irq
15 at device 15.4 on pci0
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ehci0: <AMD CS5536 (Geode) USB 2.0 controller> mem
0xefffd000-0xefffdfff irq 15 at device 15.5 on pci0
ehci0: [ITHREAD]
usbus1: EHCI version 1.0
usbus1: <AMD CS5536 (Geode) USB 2.0 controller> on ehci0
cpu0 on motherboard
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xe0000-0xeafff pnpid ORM0000 on isa0
atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
ppc0: parallel port not found.
�uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
uart0: [FILTER]
uart0: console (9600,n,8,1)
RTC BIOS diagnostic error 80<clock_battery>
Timecounter "TSC" frequency 498053887 Hz quality 800
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 480Mbps High Speed USB v2.0
ad0: DMA limited to UDMA33, device found non-ATA66 cable
ad0: 1923MB <CF CARD 2GB Ver2.19K> at ata0-master UDMA33
ugen0.1: <AMD> at usbus0
uhub0: <AMD OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <AMD> at usbus1
uhub1: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
GEOM: ad0s1: geometry does not match label (64h,63s != 16h,63s).
GEOM: ad0s2: geometry does not match label (64h,63s != 16h,63s).
Root mount waiting for: usbus1 usbus0
uhub0: 4 ports with 4 removable, self powered
Root mount waiting for: usbus1
uhub1: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/ad0s1a
Setting hostuuid: 7ccdb6ca-bfde-11d3-ad57-000db9126f00.
Setting hostid: 0x82451fc6.
Entropy harvesting: interrupts ethernet point_to_point kickstart.
Starting file system checks:
/dev/ad0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1a: clean, 999522 free (3714 frags, 124476 blocks, 0.2% fragmentation)
/dev/ad0s3: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s3: clean, 102419 free (19 frags, 12800 blocks, 0.0% fragmentation)
Mounting local file systems:.
Setting hostname: zrouter.
vr1: link state changed to DOWN
vr2: link state changed to DOWN
wlan0: Ethernet address: 00:0b:6b:db:0d:70
Starting wpa_supplicant.
wlan0: no link .......wlan0: link state changed to UP
got link
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 5
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13
DHCPOFFER from 192.168.1.1
DHCPREQUEST on wlan0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.1
bound to 192.168.1.105 -- renewal in 3600 seconds.
wlan1: Ethernet address: 00:0b:6b:db:0d:70
Starting Network: lo0 vr1 vr2 ath0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet 127.0.0.1 netmask 0xff000000
vr1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8280b<RXCSUM,TXCSUM,VLAN_MTU,WOL_UCAST,WOL_MAGIC,LINKSTATE>
ether 00:0d:b9:12:6f:01
inet 192.168.100.1 netmask 0xffffff00 broadcast 192.168.100.255
media: Ethernet autoselect (none)
status: no carrier
vr2: flags=8843<UP,BROADCAST,RUNNIvNG,SIMPLEX,MULTIrCAST> metric 0 m0tu 1500
option:s=8280b<RXCSUM,T XCSUM,VLAN_MTU,WlOL_UCAST,WOL_MAGiIC,LINKSTATE>
nether 00:0d:b9:1k2:6f:02
a inet 1 0.0.0.1 netmask s0xffffff00 broadtcast 10.0.0.255
media: Ethernett autoselect (noene)
status: no carrier
ath0: cflags=8843<UP,BRhOADCAST,RUNNING,aSIMPLEX,MULTICASnT> metric 0 mtu g2290
ether 00:e0b:6b:db:0d:70
d media: IEEE 802 .11 Wireless Ethternet autoselecto mode 11g <hosta p>
status: runDning
AdditionalO routing optionsW: IP gateway=YESN.
.tarting devd
Generating host.conf.
ELF ldconfig path: /lib /usr/lib /usr/local/lib /usr/local/lib/libnet115
a.out ldconfig path: /usr/lib/aout
ldconfig: /usr/lib/aout: No such file or directory
Creating and/or trimming log files.
Starting syslogd.
Setting date via ntp.
27 Jun 19:13:40 ntpdate[1291]: step time server 201.120.53.179 offset
362517141.849727 sec
Clearing /tmp (X related).
Updating motd:.
Starting dhcpd.
Internet Systems Consortium DHCP Server V3.1-ESV
Copyright 2004-2010 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Wrote 0 leases to leases file.
Listening on BPF/wlan1/00:0b:6b:db:0d:70/172.16.0/24
Sending on BPF/wlan1/00:0b:6b:db:0d:70/172.16.0/24
Listening on BPF/vr1/00:0d:b9:12:6f:01/192.168.100/24
Sending on BPF/vr1/00:0d:b9:12:6f:01/192.168.100/24
Sending on Socket/fallback/fallback-net
Starting cherokee.
Cherokee Web Server 1.2.2 (Jun 26 2011): Listening on port ALL:80, TLS
disabled, IPv6 disabled, using kqueue, 3578 fds system limit, max. 1782
connections, 5 threads, 356 connections per thread, standard scheduling policy
Starting sshd.
Starting cron.
Starting hostapd.
Configuration file: /etc/hostapd.conf
Using interface wlan1 with hwaddr 00:0b:6b:db:0d:70 and ssid 'SIPS2'
Starting background file system checks in 60 seconds.
Mon Jun 27 19:13:44 UTC 2011
FreeBSD/i386 (zrouter) (ttyu0)
login:
########################################
The NanoBSD image was compiled whith this kernel configuration file:
#GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the config(5) manual page,
# and/or the handbook section on Kernel Configuration Files:
#
# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files.
# If you are in doubt as to the purpose or necessity of a line, check first
# in NOTES.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.519.2.12.2.1 2010/12/21
17:09:25 kensmith Exp $
cpu I486_CPU
cpu I586_CPU
cpu I686_CPU
ident ZROUTER
# To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" # Default places to look for devices.
# Use the following to compile in values accessible to the kernel
# through getenv() (or kenv(1) in userland). The format of the file
# is 'variable=value', see kenv(1)
#
# env "GENERIC.env"
makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols
options SCHED_ULE # ULE scheduler
options PREEMPTION # Enable kernel thread preemption
options INET # InterNETworking
#options INET6 # IPv6 communications protocols
#options SCTP # Stream Control Transmission Protocol
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates support
options UFS_ACL # Support for access control lists
options UFS_DIRHASH # Improve performance on big directories
options UFS_GJOURNAL # Enable gjournal-based UFS journaling
options MD_ROOT # MD is a potential root device
#options NFSCLIENT # Network Filesystem Client
#options NFSSERVER # Network Filesystem Server
#options NFSLOCKD # Network Lock Manager
#options NFS_ROOT # NFS usable as /, requires NFSCLIENT
options MSDOSFS # MSDOS Filesystem
options CD9660 # ISO 9660 Filesystem
options PROCFS # Process filesystem (requires PSEUDOFS)
options PSEUDOFS # Pseudo-filesystem framework
options GEOM_PART_GPT # GUID Partition Tables.
options GEOM_LABEL # Provides labelization
options COMPAT_43TTY # BSD 4.3 TTY compat (sgtty)
options COMPAT_FREEBSD4 # Compatible with FreeBSD4
options COMPAT_FREEBSD5 # Compatible with FreeBSD5
options COMPAT_FREEBSD6 # Compatible with FreeBSD6
options COMPAT_FREEBSD7 # Compatible with FreeBSD7
options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI
options KTRACE # ktrace(1) support
options STACK # stack(9) support
options SYSVSHM # SYSV-style shared memory
options SYSVMSG # SYSV-style message queues
options SYSVSEM # SYSV-style semaphores
options P1003_1B_SEMAPHORES # POSIX-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time
extensions
options PRINTF_BUFR_SIZE=128 # Prevent printf output being
interspersed.
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options HWPMC_HOOKS # Necessary kernel hooks for hwpmc(4)
options AUDIT # Security event auditing
options MAC # TrustedBSD MAC Framework
options FLOWTABLE # per-cpu routing cache
#options KDTRACE_HOOKS # Kernel DTrace hooks
options INCLUDE_CONFIG_FILE # Include this file in kernel
options VIMAGE
options KDB # Kernel debugger related code
options KDB_TRACE # Print a stack trace for a panic
# To make an SMP kernel, the next two lines are needed
options SMP # Symmetric MultiProcessor Kernel
device apic # I/O APIC
# CPU frequency control
device cpufreq
# Bus support.
device acpi
device eisa
device pci
options ALTQ
options ALTQ_CBQ # Class Bases Queuing (CBQ)
options ALTQ_RED # Random Early Detection (RED)
options ALTQ_RIO # RED In/Out
options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC)
options ALTQ_PRIQ # Priority Queuing (PRIQ)
options ALTQ_NOPCC # Required for SMP build
device pf
device pflog
device pfsync
device vlan
device epair
device if_bridge
device carp
device lagg
# Floppy drives
device fdc
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device ataraid # ATA RAID drives
#device atapicd # ATAPI CDROM drives
#device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID # Static device numbering
# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
device ahd # AHA39320/29320 and onboard AIC79xx devices
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
#device amd # AMD 53C974 (Tekram DC-390(T))
#device hptiop # Highpoint RocketRaid 3xxx series
#device isp # Qlogic family
##device ispfw # Firmware for QLogic HBAs-
normally a module
#device mpt # LSI-Logic MPT-Fusion
##device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets +
those of `ncr')
#device trm # Tekram DC395U/UW/F DC315U adapters
#device adv # Advansys SCSI adapters
#device adw # Advansys wide SCSI adapters
#device aha # Adaptec 154x SCSI adapters
#device aic # Adaptec 15[012]x SCSI adapters, AIC-6[23]60.
#device bt # Buslogic/Mylex MultiMaster SCSI adapters
#device ncv # NCR 53C500
#device nsp # Workbit Ninja SCSI-3
#device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required for SCSI)
device ch # SCSI media changers
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
device ses # SCSI Environmental Services (and SAF-TE)
# RAID controllers interfaced to the SCSI subsystem
#device amr # AMI MegaRAID
#device arcmsr # Areca SATA II RAID
#device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device ciss # Compaq Smart RAID 5*
#device dpt # DPT Smartcache III, IV - See NOTES for options
#device hptmv # Highpoint RocketRAID 182x
#device hptrr # Highpoint RocketRAID 17xx, 22xx, 23xx, 25xx
#device iir # Intel Integrated RAID
#device ips # IBM (Adaptec) ServeRAID
#device mly # Mylex AcceleRAID/eXtremeRAID
#device twa # 3ware 9000 series PATA/SATA RAID
# RAID controllers
#device aac # Adaptec FSA RAID
#device aacp # SCSI passthrough for aac (requires CAM)
#device ida # Compaq Smart RAID
#device mfi # LSI MegaRAID SAS
#device mlx # Mylex DAC960 family
#device pst # Promise Supertrak SX6000
#device twe # 3ware ATA RAID
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
device kbdmux # keyboard multiplexer
device vga # VGA video card driver
#device splash # Splash screen and screen saver support
# syscons is the default console driver, resembling an SCO console
device sc
device agp # support several AGP chipsets
# Power management support (see NOTES for more options)
#device apm
# Add suspend/resume support for the i8254.
device pmtimer
# PCCARD (PCMCIA) support
# PCMCIA and cardbus bridge support
device cbb # cardbus (yenta) bridge
device pccard # PC Card (16-bit) bus
device cardbus # CardBus (32-bit) bus
# Serial (COM) ports
device uart # Generic UART driver
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# If you've got a "dumb" serial or parallel PCI card that is
# supported by the puc(4) glue driver, uncomment the following
# line to enable it (connects to sio, uart and/or ppc drivers):
#device puc
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device em # Intel PRO/1000 Gigabit Ethernet Family
#device igb # Intel PRO/1000 PCIE Server Gigabit Family
#device ixgb # Intel PRO/10GbE Ethernet Card
#device le # AMD Am7900 LANCE and Am79C9xx PCnet
#device ti # Alteon Networks Tigon I/II gigabit Ethernet
#device txp # 3Com 3cR990 (``Typhoon'')
#device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
#device ae # Attansic/Atheros L2 FastEthernet
#device age # Attansic/Atheros L1 Gigabit Ethernet
#device alc # Atheros AR8131/AR8132 Ethernet
#device ale # Atheros AR8121/AR8113/AR8114 Ethernet
#device bce # Broadcom BCM5706/BCM5708 Gigabit Ethernet
#device bfe # Broadcom BCM440x 10/100 Ethernet
#device bge # Broadcom BCM570xx Gigabit Ethernet
#device dc # DEC/Intel 21143 and various workalikes
#device et # Agere ET1310 10/100/Gigabit Ethernet
#device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device jme # JMicron JMC250 Gigabit/JMC260 Fast Ethernet
#device lge # Level 1 LXT1001 gigabit Ethernet
#device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
#device nfe # nVidia nForce MCP on-board Ethernet
#device nge # NatSemi DP83820 gigabit Ethernet
##device nve # nVidia nForce MCP on-board
Ethernet Networking
#device pcn # AMD Am79C97x PCI 10/100 (precedence over 'le')
device re # RealTek 8139C+/8169/8169S/8110S
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sge # Silicon Integrated Systems SiS190/191
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device sk # SysKonnect SK-984x & SK-982x gigabit Ethernet
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device stge # Sundance/Tamarack TC9021 gigabit Ethernet
#device tl # Texas Instruments ThunderLAN
#device tx # SMC EtherPower II (83c170 ``EPIC'')
#device vge # VIA VT612x gigabit Ethernet
device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs. pccard NICs included.
device cs # Crystal Semiconductor CS89x0 NIC
# 'device ed' requires 'device miibus'
#device ed # NE[12]000, SMC Ultra, 3c503, DS8390 cards
#device ex # Intel EtherExpress Pro/10 and Pro/10+
#device ep # Etherlink III based cards
#device fe # Fujitsu MB8696x based cards
#device ie # EtherExpress 8/16, 3C507, StarLAN 10 etc.
#device sn # SMC's 9000 series of Ethernet chips
#device xe # Xircom pccard Ethernet
# Wireless NIC cards
device wlan # 802.11 support
options IEEE80211_DEBUG # enable debug msgs
options IEEE80211_AMPDU_AGE # age frames in AMPDU reorder q's
options IEEE80211_SUPPORT_MESH # enable 802.11s draft support
device wlan_wep # 802.11 WEP support
device wlan_ccmp # 802.11 CCMP support
device wlan_tkip # 802.11 TKIP support
device wlan_amrr # AMRR transmit rate control algorithm
device an # Aironet 4500/4800 802.11 wireless NICs.
device ath # Atheros pci/cardbus NIC's
device ath_hal # pci/cardbus chip support
options AH_SUPPORT_AR5416 # enable AR5416 tx/rx descriptors
device ath_rate_sample # SampleRate tx rate control for ath
device ral # Ralink Technology RT2500 wireless NICs.
device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs.
#device wl # Older non 802.11 Wavelan wireless NIC.
# Pseudo devices.
device loop # Network loopback
device random # Entropy device
device ether # Ethernet support
device vlan # 802.1Q VLAN support
device tun # Packet tunnel.
device pty # BSD-style compatibility pseudo ttys
device md # Memory "disks"
device gif # IPv6 and IPv4 tunneling
device faith # IPv6-to-IPv4 relaying (translation)
device firmware # firmware assist module
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
# Note that 'bpf' is required for DHCP.
device bpf # Berkeley packet filter
# USB support
options USB_DEBUG # enable debug msgs
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device ehci # EHCI PCI->USB interface (USB 2.0)
device usb # USB Bus (required)
#device udbp # USB Double Bulk Pipe devices
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device urio # Diamond Rio 500 MP3 player
# USB Serial devices
device u3g # USB-based 3G modems (Option, Huawei, Sierra)
device uark # Technologies ARK3116 based serial adapters
device ubsa # Belkin F5U103 and compatible serial adapters
device uftdi # For FTDI usb serial adapters
device uipaq # Some WinCE based devices
device uplcom # Prolific PL-2303 serial adapters
device uslcom # SI Labs CP2101/CP2102 serial adapters
device uvisor # Visor and Palm devices
device uvscom # USB serial support for DDI pocket's PHS
# USB Ethernet, requires miibus
device aue # ADMtek USB Ethernet
device axe # ASIX Electronics USB Ethernet
device cdce # Generic USB over Ethernet
device cue # CATC USB Ethernet
device kue # Kawasaki LSI USB Ethernet
device rue # RealTek RTL8150 USB Ethernet
device udav # Davicom DM9601E USB
# USB Wireless
device rum # Ralink Technology RT2501USB wireless NICs
device uath # Atheros AR5523 wireless NICs
device ural # Ralink Technology RT2500USB wireless NICs
device zyd # ZyDAS zb1211/zb1211b wireless NICs
# FireWire support
#device firewire # FireWire bus code
#device sbp # SCSI over FireWire (Requires scbus and da)
#device fwe # Ethernet over FireWire (non-standard!)
#device fwip # IP over FireWire (RFC 2734,3146)
#device dcons # Dumb console driver
#device dcons_crom # Configuration ROM for dcons
#####################################
Before I updated my Nanobsd image from FreeBSD 8.1 to 8.2 RELEASE my
alix board worked very well, the big diference between my old nanobsd
image and my new nanobsd image is that the new one have "option
VIMAGE" active.
Could someone help me ?
If there is some another thing that you need to figure out what was
happen please let me know.
Thanks a lot.
PD: If this is the incorrect list for this item please let me know it.
More information about the freebsd-pf
mailing list