Carp master problem
Chris McGee
chris at gliq.com
Thu Jun 30 14:41:13 GMT 2005
Constant, Benjamin wrote:
>Simple questions but do you see multicast traffic on em0? Are there firewall
>rules on em0 that can prevent such traffic?
>
>Regards,
>
>Benjamin Constant
>TI Automotive
>
>
>
>>-----Original Message-----
>>From: owner-freebsd-pf at freebsd.org
>>[mailto:owner-freebsd-pf at freebsd.org] On Behalf Of Chris McGee
>>Sent: jeudi 30 juin 2005 6:38
>>To: freebsd-pf at freebsd.org
>>Subject: Carp master problem
>>
>>I have to machines in a test environment, the carp0 interface
>>on the machines will not become master. The config is as follows:
>>
>>test1# ifconfig
>>em0:
>>flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
>> options=b<RXCSUM,TXCSUM,VLAN_MTU>
>> inet 192.168.1.252 netmask 0xffffff00 broadcast 192.168.1.255
>> inet6 fe80::230:48ff:fe82:a77c%em0 prefixlen 64 scopeid 0x1
>> ether 00:30:48:82:a7:7c
>> media: Ethernet autoselect (100baseTX <full-duplex>)
>> status: active
>>em1:
>>flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
>> options=b<RXCSUM,TXCSUM,VLAN_MTU>
>> inet 10.10.10.2 netmask 0xfffffff8 broadcast 10.10.10.7
>> inet6 fe80::230:48ff:fe82:a77d%em1 prefixlen 64 scopeid 0x2
>> ether 00:30:48:82:a7:7d
>> media: Ethernet autoselect (100baseTX <full-duplex>)
>> status: active
>>carp0: flags=41<UP,RUNNING> mtu 1500
>> inet 192.168.1.10 netmask 0xffffff00
>> carp: BACKUP vhid 1 advbase 1 advskew 0
>>carp1: flags=41<UP,RUNNING> mtu 1500
>> inet 10.10.10.1 netmask 0xfffffff8
>> carp: MASTER vhid 2 advbase 1 advskew 0
>>
>>em0:
>>flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
>> options=b<RXCSUM,TXCSUM,VLAN_MTU>
>> inet 192.168.1.253 netmask 0xffffff00 broadcast 192.168.1.255
>> inet6 fe80::230:48ff:fe80:21bc%em0 prefixlen 64 scopeid 0x1
>> ether 00:30:48:80:21:bc
>> media: Ethernet autoselect (100baseTX <full-duplex>)
>> status: active
>>em1:
>>flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
>> options=b<RXCSUM,TXCSUM,VLAN_MTU>
>> inet 10.10.10.3 netmask 0xfffffff8 broadcast 10.10.10.7
>> inet6 fe80::230:48ff:fe80:21bd%em1 prefixlen 64 scopeid 0x2
>> ether 00:30:48:80:21:bd
>> media: Ethernet autoselect (100baseTX <full-duplex>)
>> status: active
>>carp0: flags=41<UP,RUNNING> mtu 1500
>> inet 192.168.1.10 netmask 0xffffff00
>> carp: BACKUP vhid 1 advbase 1 advskew 100
>>carp1: flags=41<UP,RUNNING> mtu 1500
>> inet 10.10.10.1 netmask 0xfffffff8
>> carp: BACKUP vhid 2 advbase 1 advskew 100
>>
>>both test1 and test2 have these sysctl variables:
>>net.inet.carp.allow: 1
>>net.inet.carp.preempt: 1
>>net.inet.carp.log: 1
>>net.inet.carp.arpbalance: 0
>>
>>If I down the carp1 interface on either box the other box
>>becomes master. If I down the carp0 interface on either box,
>>the other stays backup. Both carp0 interfaces stay backup
>>all the time and therefore I can't access 192.168.1.10.
>>
>>Thanks,
>>Chris
>>
>>_______________________________________________
>>freebsd-pf at freebsd.org mailing list
>>http://lists.freebsd.org/mailman/listinfo/freebsd-pf
>>To unsubscribe, send any mail to "freebsd-pf-unsubscribe at freebsd.org"
>>
>>
>>
>
>The information contained in this transmission may contain privileged and
>confidential information. It is intended only for the use of the
>person(s) named above. If you are not the intended recipient, you are
>hereby notified that any review, dissemination, distribution or
>duplication of this communication is strictly prohibited. If you are not
>the intended recipient, please contact the sender by reply email and
>destroy all copies of the original message. This communication is from TI
>Automotive.
>
>
I see multicast advertisements going out on em0 on what should be the
master (test1) and I see those advertisements on test2 also. The only
firewall rules are the default, pass in all, and pass out all. No
firewall rules have been setup yet since this is a test environment.
Chris
More information about the freebsd-pf
mailing list