Discrepancy on netstat -w x -I and what Cisco reports
Paul
paul at gtcomm.net
Mon May 12 18:50:07 UTC 2008
Yes it was a typo I meant -w -I
It just doesn't add up to what the switch is seeing, and it's directly
connected and the traffic can't be going anywhere else.
Stefan Lambrev wrote:
> Greetings,
>
> I just have a question:
>
> is "netstat -w 100 lagg0" a typo ?
>
> If you want to see the traffic only on single interface you should use -I
>
> I do not know if this is bug, but netstat -w 100
> something_non_existing works on my bsd and just shows "Total"
>
> So may be from here comes the confusion. You think, that netstat count
> only traffic on lagg0,
> but it shows you the Total traffic?
>
> Paul wrote:
>> This is very strange.. I can do:
>>
>> netstat -w 10 -I lagg0
>> input (lagg0) output
>> packets errs bytes packets errs bytes colls
>> 57806 0 41751685 232442 0 51062425 0
>> 56459 0 38341591 225146 0 48865209 0
>> 60687 0 43552946 227987 0 52008241 0
>>
>> which is roughly 23,000 pps and the Cisco switch reports
>> 30 second input rate 44544000 bits/sec, 16198 packets/sec
>>
>>
>> Another example:
>>
>> netstat -w 10 -I lagg0
>> input (lagg0) output
>> packets errs bytes packets errs bytes colls
>> 71111 0 52180947 89734 0 25304669 0
>> 66847 0 49028588 81737 0 21614941 0
>> 63530 0 43502418 83419 0 24599547 0
>>
>> 8,300 or so pps
>>
>> Cisco:
>> 30 second input rate 19230000 bits/sec, 4594 packets/sec
>>
>>
>> In some cases it's pretty close, cisco says 6500 and bsd says 7500..
>> but sometimes it is way off
>> I even checked the em interfaces directly to see if it was a problem
>> with the lagg interface code and they report weird issues, check below.
>> Kind of weird.. I'm not sure if this is a Cisco issue or Fbsd issue
>> with the counters.
>> It's two different Cisco switches and two fbsd machines that have the
>> same kernel, etc.
>>
>> Maybe this is a side effect of setting my kernel HZ at 4000?
>> Gets even worse like this:
>> netstat -w 100 lagg0
>> input (Total) output
>> packets errs bytes packets errs bytes colls
>> 9229322 0 3337789024 9424932 0 3510341158 0
>>
>> 100 seconds, 9.4 million packets? That's 94,000 pps and cisco reports
>> 2 minute input rate 44130000 bits/sec, 14892 packets/sec
> Again this is Total not lagg0
>> and even check this out:
>>
>> netstat -w 1 lagg0
>> input *(Total) * output
>> packets errs bytes packets errs bytes colls
>> 92481 0 31630795 94952 0 34193131 0
>> 89078 0 32498082 91460 0 35094821 0
>> 87540 0 34526292 89992 0 37159101 0
>> 88987 0 32391984 91765 0 35394351 0
>>
>>
>> netstat -w 1 em0
>> input *(Total) * output
>> packets errs bytes packets errs bytes colls
>> 96802 0 39474036 99897 0 42814245 0
>> 93277 0 37018533 95943 0 39860879 0
>> 95916 0 37559076 99032 0 40739640 0
>>
>> netstat -w 1 em1
>> input * (Total) * output
>> packets errs bytes packets errs bytes colls
>> 97102 0 38369949 99508 0 40841183 0
>> 92321 0 35375169 94305 0 37384073 0
>> 92225 0 33171455 94253 0 35209658 0
>>
>> What in the world?? em0 + em1 is almost 200k pps but lagg0 says 100k
>> and i KNOW it's not doing anywhere near..
>> cisco report
>> 2 minute output rate 32928000 bits/sec, 5823 packets/sec
> Again missing -I :)
>>
>> Now all lagg interfaces are reporting
>> netstat -w 1 lagg1
>> input * (Total) * output
>> packets errs bytes packets errs bytes colls
>> 89324 0 30824353 91518 0 32770482 0
>> 85875 0 31924738 87813 0 33552137 0
>> 84105 0 31176932 85666 0 32393051 0
>> 83617 0 32175677 84871 0 33120271 0
>> 90611 0 37313093 92403 0 38818721 0
>>
>> lagg1 goes directly to another freebsd box and on the other freebsd
>> box I do:
>> netstat -w 1 -I lagg1
>> input (lagg1) output
>> packets errs bytes packets errs bytes colls
>> 45 0 3078 2213 0 1890198 0
>> 48 0 3245 1958 0 1545642 0
>> 43 0 3186 1975 0 1628916 0
>> 43 0 2905 2169 0 1918250 0
>> 46 0 3464 1859 0 1729764 0
>> 46 0 3134 1873 0 1739662 0
>>
>> and the other one
>> netstat -w 1 lagg1
>> input * (Total)* output
>> packets errs bytes packets errs bytes colls
>> 92149 0 31706183 93523 0 32673138 0
>> 89737 0 28119643 91323 0 28958816 0
>>
>>
>> Doing all these reports now seems to have the interfaces stuck at
>> packets errs bytes packets errs bytes colls
>> 96937 0 31749525 98551 0 32678863 0
>> 85892 0 29411078 87233 0 30182355 0
>> 90435 0 31628680 91620 0 32215244 0
>> 87383 0 30616741 88278 0 31026608 0
>>
>>
>> every interface on the machine is reporting the same PPS and bytes..
>> lol :)
>>
>> So something is extremely fishy about the counters.. I'm going to try
>> and update to -STABLE to see if it makes any difference. It's not
>> just the lagg interface either because all the em's are showing it as
>> well.
>>
>> This is using 4 port Intel Server PCI Express NIC
>>
>> ifstat seems to report correct usage in Kbps and seems to report
>> correct packet count. Maybe it's just a netstat problem?
>>
>> I will see if stable fixes it. Also, feel free to make any comments
>> on my config file for routing.
>>
>> FreeBSD 7.0-RELEASE-p1 FreeBSD 7.0-RELEASE-p1 #6: Thu Apr 17
>> 18:11:49 EDT 2008 amd64
>>
>>
>> UPDATE.. Changed 1 router to stable:
>> FreeBSD 7.0-STABLE FreeBSD 7.0-STABLE #5: Sun May 11 19:00:57 EDT
>> 2008 amd64
>>
>> Still see:
>> 2 minute input rate 10463000 bits/sec, 2481 packets/sec
>> 2 minute output rate 40075000 bits/sec, 6847 packets/sec
>>
>> and
>> input (lagg0) output
>> packets errs bytes packets errs bytes colls
>> 6940 0 5172153 4841 0 1345660 0
>> 5922 0 4252074 3963 0 1087205 0
>> 6673 0 4982394 4116 0 1056933 0
>> 6659 0 4467398 4140 0 1068919 0
>> 7085 0 4692973 4777 0 1665109 0
>> 7140 0 4654486 4713 0 1658303 0
>> 7070 0 4558384 5078 0 1994666 0
>> 6375 0 4575464 4037 0 1121385 0
>> 6257 0 3932910 4321 0 1607862 0
>> 6504 0 4345014 4370 0 1278819 0
>>
>>
>> Hmmmm..
>>
>>
>>
>>
>> em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
>> 0xece0-0xecff mem 0xd5ee0000-0xd5efffff,0xd5ec0000-0xd5edffff irq 17
>> at device 0.0 on pci12
>> em0: Using MSI interrupt
>> em0: Ethernet address: 00:15:17:5d:18:00
>> em0: [FILTER]
>> em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
>> 0xecc0-0xecdf mem 0xd5ea0000-0xd5ebffff,0xd5e80000-0xd5e9ffff irq 18
>> at device 0.1 on pci12
>> em1: Using MSI interrupt
>> em1: Ethernet address: 00:15:17:5d:18:01
>> em1: [FILTER]
>> .......etc.. to em7
>>
>>
>> Copyright (c) 1992-2008 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>> The Regents of the University of California. All rights reserved.
>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>> FreeBSD 7.0-RELEASE-p1 #6: Thu Apr 17 18:11:49 EDT 2008
>> root at CR1.MTL3.Gtcomm.net:/usr/obj/usr/src/sys/ROUTER
>> Timecounter "i8254" frequency 1193182 Hz quality 0
>> CPU: Intel(R) Xeon(R) CPU 5140 @ 2.33GHz (2329.28-MHz
>> K8-class CPU)
>> Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
>>
>> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>>
>>
>> Features2=0x4e3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA>
>>
>> AMD Features=0x20100800<SYSCALL,NX,LM>
>> AMD Features2=0x1<LAHF>
>> Cores per package: 2
>> usable memory = 4285833216 (4087 MB)
>> avail memory = 4124545024 (3933 MB)
>> ACPI APIC Table: <DELL PE_SC3 >
>> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>> cpu0 (BSP): APIC ID: 0
>> cpu1 (AP): APIC ID: 1
>> cpu2 (AP): APIC ID: 6
>> cpu3 (AP): APIC ID: 7
>> ioapic0: Changing APIC ID to 8
>> ioapic1: Changing APIC ID to 9
>>
>>
>>
>> Kernel config file: (if you have any suggestions about the config let
>> me know for faster routing speed)
>>
>> cpu HAMMER
>> ident GENERIC
>>
>> #makeoptions DEBUG=-g # Build kernel with gdb(1)
>> debug symbols
>>
>> options SCHED_4BSD # 4BSD scheduler
>> #options PREEMPTION # Enable kernel thread
>> preemption
>> options INET # InterNETworking
>> options INET6 # IPv6 communications protocols
>> options FFS # Berkeley Fast Filesystem
>> options SOFTUPDATES # Enable FFS soft updates
>> support
>> options UFS_ACL # Support for access control
>> lists
>> options UFS_DIRHASH # Improve performance on big
>> directories
>> options UFS_GJOURNAL # Enable gjournal-based UFS
>> journaling
>> options MD_ROOT # MD is a potential root device
>> options NTFS # NT File System
>> options MSDOSFS # MSDOS Filesystem
>> options CD9660 # ISO 9660 Filesystem
>> options PROCFS # Process filesystem
>> (requires PSEUDOFS)
>> options PSEUDOFS # Pseudo-filesystem framework
>> options GEOM_PART_GPT # GUID Partition Tables.
>> options GEOM_LABEL # Provides labelization
>> options COMPAT_43TTY # BSD 4.3 TTY compat [KEEP
>> THIS!]
>> options COMPAT_IA32 # Compatible with i386 binaries
>> options COMPAT_FREEBSD4 # Compatible with FreeBSD4
>> options COMPAT_FREEBSD5 # Compatible with FreeBSD5
>> options COMPAT_FREEBSD6 # Compatible with FreeBSD6
>> options SCSI_DELAY=5000 # Delay (in ms) before
>> probing SCSI
>> options KTRACE # ktrace(1) support
>> options SYSVSHM # SYSV-style shared memory
>> options SYSVMSG # SYSV-style message queues
>> options SYSVSEM # SYSV-style semaphores
>> options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B
>> real-time extensions
>> options KBD_INSTALL_CDEV # install a CDEV entry in /dev
>> #options ADAPTIVE_GIANT # Giant mutex is adaptive.
>> options NO_ADAPTIVE_MUTEXES ##
>> options STOP_NMI # Stop CPUS using NMI instead
>> of IPI
>> options AUDIT # Security event auditing
>> options IPSEC ## for tcp md5
>> options TCP_SIGNATURE ##include support for RFC 2385
>> device crypto ## for md5
>> device cryptodev ## for md5
>>
>> # Make an SMP-capable kernel by default
>> options SMP # Symmetric MultiProcessor
>> Kernel
>>
>> # CPU frequency control
>> device cpufreq
>>
>> # Bus support.
>> device acpi
>> device pci
>>
>> # Floppy drives
>> device fdc
>>
>> # ATA and ATAPI devices
>> device ata
>> device atadisk # ATA disk drives
>> device ataraid # ATA RAID drives
>> device atapicd # ATAPI CDROM drives
>> device atapifd # ATAPI floppy drives
>> device atapist # ATAPI tape drives
>> options ATA_STATIC_ID # Static device numbering
>>
>> # SCSI peripherals
>> device scbus # SCSI bus (required for SCSI)
>> device ch # SCSI media changers
>> device da # Direct Access (disks)
>> device sa # Sequential Access (tape etc)
>> device cd # CD
>> device pass # Passthrough device (direct SCSI
>> access)
>> device ses # SCSI Environmental Services (and
>> SAF-TE)
>>
>> # RAID controllers
>> device mfi # LSI MegaRAID SAS
>>
>> # atkbdc0 controls both the keyboard and the PS/2 mouse
>> device atkbdc # AT keyboard controller
>> device atkbd # AT keyboard
>> device psm # PS/2 mouse
>>
>> device kbdmux # keyboard multiplexer
>>
>> device vga # VGA video card driver
>>
>> device splash # Splash screen and screen saver support
>>
>> # syscons is the default console driver, resembling an SCO console
>> device sc
>>
>> device agp # support several AGP chipsets
>>
>> # Serial (COM) ports
>> device sio # 8250, 16[45]50 based serial ports
>> device uart # Generic UART driver
>>
>> # PCI Ethernet NICs.
>> device em # Intel PRO/1000 adapter Gigabit
>> Ethernet Card
>> # PCI Ethernet NICs that use the common MII bus controller code.
>> # NOTE: Be sure to keep the 'device miibus' line in order to use
>> these NICs!
>> device miibus
>> device bce # Broadcom BCM5706/BCM5708 Gigabit
>> Ethernet
>>
>> # Pseudo devices.
>> device loop # Network loopback
>> device random # Entropy device
>> device ether # Ethernet support
>> device sl # Kernel SLIP
>> device ppp # Kernel PPP
>> device tun # Packet tunnel.
>> device pty # Pseudo-ttys (telnet etc)
>> device md # Memory "disks"
>> device gif # IPv6 and IPv4 tunneling
>> device faith # IPv6-to-IPv4 relaying (translation)
>> device firmware # firmware assist module
>>
>> # The `bpf' device enables the Berkeley Packet Filter.
>> # Be aware of the administrative consequences of enabling this!
>> # Note that 'bpf' is required for DHCP.
>> device bpf # Berkeley packet filter
>>
>> # USB support
>> device uhci # UHCI PCI->USB interface
>> device ohci # OHCI PCI->USB interface
>> device ehci # EHCI PCI->USB interface (USB 2.0)
>> device usb # USB Bus (required)
>> #device udbp # USB Double Bulk Pipe devices
>> device ugen # Generic
>> device uhid # "Human Interface Devices"
>> device ukbd # Keyboard
>> device umass # Disks/Mass storage - Requires scbus
>> and da
>> device ums # Mouse
>>
>> ### OPTIONS
>>
>>
>> options MP_WATCHDOG
>> options DEVICE_POLLING
>> device pf
>> device pflog
>> device pfsync
>> device carp
>> device vlan
>> device gre
>> device if_bridge
>> device tun
>> device lagg
>> device stf #6to4 IPv6 over IPv4 encapsulation
>>
>> options ALTQ
>> options ALTQ_CBQ # Class Bases Queuing (CBQ)
>> options ALTQ_RED # Random Early Detection (RED)
>> options ALTQ_RIO # RED In/Out
>> options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC)
>> options ALTQ_CDNR
>> options ALTQ_PRIQ # Priority Queuing (PRIQ)
>> options ALTQ_NOPCC # Required for SMP build
>>
>>
>>
>> options NETGRAPH
>> options NETGRAPH_CISCO
>> options NETGRAPH_FEC
>> options NETGRAPH_ETHER
>>
>>
>>
>>
>>
>> Copyright (c) 1992-2008 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>> The Regents of the University of California. All rights reserved.
>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>> FreeBSD 7.0-STABLE #5: Sun May 11 19:00:57 EDT 2008
>> root at CR2.MTL3.Gtcomm.net:/usr/obj/usr/src/sys/ROUTER
>> Timecounter "i8254" frequency 1193182 Hz quality 0
>> CPU: Intel(R) Xeon(R) CPU 5140 @ 2.33GHz (2329.26-MHz
>> K8-class CPU)
>> Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
>>
>> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>>
>>
>> Features2=0x4e3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA>
>>
>> AMD Features=0x20100800<SYSCALL,NX,LM>
>> AMD Features2=0x1<LAHF>
>> Cores per package: 2
>> usable memory = 4286042112 (4087 MB)
>> avail memory = 4124753920 (3933 MB)
>> ACPI APIC Table: <DELL PE_SC3 >
>> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>> cpu0 (BSP): APIC ID: 0
>> cpu1 (AP): APIC ID: 1
>> cpu2 (AP): APIC ID: 6
>> cpu3 (AP): APIC ID: 7
>> ioapic0: Changing APIC ID to 8
>> ioapic1: Changing APIC ID to 9
>> ioapic0 <Version 2.0> irqs 0-23 on motherboard
>> ioapic1 <Version 2.0> irqs 64-87 on motherboard
>> kbd1 at kbdmux0
>> cryptosoft0: <software crypto> on motherboard
>> acpi0: <DELL PE_SC3> on motherboard
>> acpi0: [ITHREAD]
>> acpi0: Power Button (fixed)
>> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
>> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
>> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff
>> on acpi0
>> Timecounter "HPET" frequency 14318180 Hz quality 900
>> cpu0: <ACPI CPU> on acpi0
>> est0: <Enhanced SpeedStep Frequency Control> on cpu0
>> est: CPU supports Enhanced Speedstep, but is not recognized.
>> est: cpu_vendor GenuineIntel, msr 728072806000728
>> device_attach: est0 attach returned 6
>> p4tcc0: <CPU Frequency Thermal Control> on cpu0
>> cpu1: <ACPI CPU> on acpi0
>> est1: <Enhanced SpeedStep Frequency Control> on cpu1
>> est: CPU supports Enhanced Speedstep, but is not recognized.
>> est: cpu_vendor GenuineIntel, msr 728072806000728
>> device_attach: est1 attach returned 6
>> p4tcc1: <CPU Frequency Thermal Control> on cpu1
>> cpu2: <ACPI CPU> on acpi0
>> est2: <Enhanced SpeedStep Frequency Control> on cpu2
>> est: CPU supports Enhanced Speedstep, but is not recognized.
>> est: cpu_vendor GenuineIntel, msr 728072806000728
>> device_attach: est2 attach returned 6
>> p4tcc2: <CPU Frequency Thermal Control> on cpu2
>> cpu3: <ACPI CPU> on acpi0
>> est3: <Enhanced SpeedStep Frequency Control> on cpu3
>> est: CPU supports Enhanced Speedstep, but is not recognized.
>> est: cpu_vendor GenuineIntel, msr 728072806000728
>> device_attach: est3 attach returned 6
>> p4tcc3: <CPU Frequency Thermal Control> on cpu3
>> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
>> pci0: <ACPI PCI bus> on pcib0
>> pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
>> pci6: <ACPI PCI bus> on pcib1
>> pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci6
>> pci7: <ACPI PCI bus> on pcib2
>> pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci7
>> pci8: <ACPI PCI bus> on pcib3
>> pcib4: <PCI-PCI bridge> at device 0.0 on pci8
>> pci9: <PCI bus> on pcib4
>> bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
>> 0xd6000000-0xd7ffffff irq 16 at device 0.0 on pci9
>> miibus0: <MII bus> on bce0
>> brgphy0: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus0
>> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
>> 1000baseT-FDX, auto
>> bce0: Ethernet address: 00:19:b9:cd:60:44
>> bce0: [ITHREAD]
>> bce0: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); F/W
>> (0x02090105); Flags( MFW MSI )
>> pcib5: <ACPI PCI-PCI bridge> at device 1.0 on pci7
>> pci10: <ACPI PCI bus> on pcib5
>> pcib6: <PCI-PCI bridge> at device 0.0 on pci10
>> pci11: <PCI bus> on pcib6
>> pcib7: <PCI-PCI bridge> at device 0.0 on pci11
>> pci12: <PCI bus> on pcib7
>> em0: <Intel(R) PRO/1000 Network Connection 6.9.0> port 0xece0-0xecff
>> mem 0xd5ee0000-0xd5efffff,0xd5ec0000-0xd5edffff irq 17 at device 0.0
>> on pci12
>> em0: Using MSI interrupt
>> em0: [FILTER]
>> em0: Ethernet address: 00:15:17:5d:2a:40
>> em1: <Intel(R) PRO/1000 Network Connection 6.9.0> port 0xecc0-0xecdf
>> mem 0xd5ea0000-0xd5ebffff,0xd5e80000-0xd5e9ffff irq 18 at device 0.1
>> on pci12
>> em1: Using MSI interrupt
>> em1: [FILTER]
>> em1: Ethernet address: 00:15:17:5d:2a:41
>> pcib8: <PCI-PCI bridge> at device 1.0 on pci11
>> pci13: <PCI bus> on pcib8
>> em2: <Intel(R) PRO/1000 Network Connection 6.9.0> port 0xdce0-0xdcff
>> mem 0xd5ce0000-0xd5cfffff,0xd5cc0000-0xd5cdffff irq 18 at device 0.
>>
>>
>> lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0
>> mtu 1500
>> options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4>
>> ether 00:15:17:5d:2a:40
>> media: Ethernet autoselect
>> status: active
>> laggproto lacp
>> laggport: em1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
>> laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
>>
>>
>> lagg1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0
>> mtu 1500
>> options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4>
>> ether 00:15:17:5d:28:62
>> inet netmask 0xfffffffc broadcast
>> media: Ethernet autoselect
>> status: active
>> laggproto lacp
>> laggport: em7 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
>> laggport: em6 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
>>
>> lagg2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0
>> mtu 1500
>> options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4>
>> ether 00:15:17:5d:28:60
>> media: Ethernet autoselect
>> status: active
>> laggproto lacp
>> laggport: em5 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
>> laggport: em4 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
>>
>>
>> _______________________________________________
>> freebsd-net at freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-net
>> To unsubscribe, send any mail to "freebsd-net-unsubscribe at freebsd.org"
>
> --
>
> Best Wishes,
> Stefan Lambrev
> ICQ# 24134177
>
More information about the freebsd-net
mailing list