HOWTO connect MCI using Netgraph + Frame Relay with Digi SYNC/570i

[c0ldbyte]

On Tue, 29 Mar 2005, John Mok wrote:

>
> After issuing the following commands :-
>
> #ngctl mkpeer sync_ar0: frame_relay rawdata downstream
> #ngctl mkpeer sync_ar0:rawdata lmi dlci0 ansi
> #ngctl mkpeer sync_ar0:rawdata rfc1490 dlci16 rfc1490
> #ngctl mkpeer sync_ar0:rawdata dlci16 rl0 inet inet
> #ifconfig ng0 1.2.3.4 5.6.7.8
> ifconfig: interface ng0 does not exist
>
> The command ifconfig shows :-
>
> rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>   options=8<VLAN_MTU>
>   inet6 fe80::207:40ff:fe09:f09%rl0 prefixlen 64 scopeid 0x1
>   inet 192.168.255.254 netmask 0xffffff00 broadcast 192.168.255.255
>   ether 00:07:40:09:0f:09
>   media: Ethernet autoselect (none)
>   status: no carrier
> xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>   options=9<RXCSUM,VLAN_MTU>
>   inet6 fe80::201:3ff:fec1:9c58%xl0 prefixlen 64 scopeid 0x2
>   ether 00:01:03:c1:9c:58
>   media: Ethernet autoselect (100baseTX <full-duplex>)
>   status: active
> xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>   options=9<RXCSUM,VLAN_MTU>
>   inet6 fe80::201:3ff:fe34:61af%xl1 prefixlen 64 scopeid 0x3
>   inet 192.168.16.254 netmask 0xffffff00 broadcast 192.168.16.255
>   ether 00:01:03:34:61:af
>   media: Ethernet autoselect (100baseTX <full-duplex>)
>   status: active
> plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
>   inet6 ::1 prefixlen 128
>   inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
>   inet 127.0.0.1 netmask 0xff000000
>
> and the command "ngctl list" shows :-
>
> There are 4 total nodes:
> Name: ngctl811        Type: socket          ID: 00000011   Num hooks: 0
> Name: <unnamed>       Type: frame_relay     ID: 00000004   Num hooks: 1
> Name: sync_ar1        Type: sync_ar         ID: 00000002   Num hooks: 0
> Name: sync_ar0        Type: sync_ar         ID: 00000001   Num hooks: 1
>
> Would it be the problem that I test it with cable disconnected from the modem 
> (i.e.CSU/DSU)?
>
> Thanks a lot.
>
> John Mok
>
>
> Julian Elischer wrote:
>
>> did the last command do anything?
>> 
>> please show the output of:
>> ifconfig
>> ngctl list
>>

You have ng_ether or ng_iface loaded ?