mutlimedia : snd_hda/driver ; No Sound, not loading properly ;
Asus P5B
Rick Nekus
solarux at hotmail.com
Wed Apr 18 11:22:56 UTC 2007
Hi All,
-I was trying to get the below mentioned hardware going and followed
instructiuons as per
[1]http://people.freebsd.org/~ariff/lowlatency/README
If I have left anything out,? or you feel I flubbed somethin up ? or
you need any other info just shout.
thanks,.
Rick.
-------------------------
Hardware/chipset : Asus P5B Premium Motherboard/Intel P965/ICH85
Audio/chip : ADI AD1988-B 8/Ch HDA codec
-I've (hopefully) attched the verbose booting dmesg.
# uname -a
FreeBSD 6.2-STABLE-200704 i386
-(theres no X, kde,... yet)
# dmesg | grep -i ^pcm
pcm0: <Intel 82801H High Definition Audio Controller> mem
0xfebfc000-0xfebfffff irq 22 at device 27.0 on pci0
pcm0: TCSEL: 0x00 -> 0x00
pcm0: DMA Coherency: Uncacheable / vendor=0x8086
pcm0: hdac_mem_alloc: Unable to allocate memory resource
# kldstat
Id Refs Address Size Name
1 5 0xc0400000 72df00 kernel
2 1 0xc0b2e000 fa18 snd_hda.ko
3 2 0xc0b3e000 22788 sound.ko
4 1 0xc0b61000 5ad74 acpi.ko
# cat /dev/sndstat
FreeBSD Audio Driver (newpcm) 64bit
Installed devices:
-thers no /dev/dsp,... ?
----------------------------------------------------------------------
------------
_________________________________________________________________
Live U's list of the best places [2]to Eat, Study & Party
References
1. http://people.freebsd.org/~ariff/lowlatency/README
2. http://g.msn.com/8HMAENCA/2743??PS=47575
-------------- next part --------------
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE-200704 #0: Sun Apr 1 11:31:16 UTC 2007
root at dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0bdc000.
Preloaded elf module "/boot/kernel/snd_hda.ko" at 0xc0bdc188.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc0bdc234.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0bdc2e0.
MP Configuration Table version 1.4 found at 0xc00f11a0
Table 'FACP' at 0x7ff70200
Table 'APIC' at 0x7ff70390
MADT: Found table at 0x7ff70390
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 2: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 130 ACPI ID 3: disabled
MADT: Found CPU APIC ID 131 ACPI ID 4: disabled
INTR: Adding local APIC 0 as a target
ACPI APIC Table: <A_M_I_ OEMAPIC >
Calibrating clock(s) ... i8254 clock: 1193248 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2400015564 Hz
CPU: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz (2400.02-MHz 686-class
CPU)
Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Cores per package: 2
real memory = 2146893824 (2047 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000007db21fff, 2096078848 bytes (511738 pages)
avail memory = 2095767552 (1998 MB)
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x31
pnpbios: Found PnP BIOS data at 0xc00f65a0
pnpbios: Entry = f0000:793a Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010000
wlan: <802.11 Link Layer>
feeder_register: snd_unit=0 snd_maxautovchans=4 latency=5
feeder_buffersize=16384 feeder_rate_min=1 feeder_rate_max=2016000
feeder_rate_round=25
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
rr232x: RocketRAID 232x controller driver v1.02 (Apr 1 2007 11:30:51)
npx0: INT 16 interface
acpi0: <NEC > on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80030004
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=29a08086)
pcibios: BIOS version 3.00
acpi_bus_number: root bus has no _BBN, assuming 0
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xda38a000 pa 0x9d000
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 11 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 10 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 7 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 7 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 15 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 15 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 5 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 3 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 3 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x29a0, revid=0x02
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x29a1, revid=0x02
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 3 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x284b, revid=0x02
bus=0, slot=27, func=0
class=04-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base febfc000, size 14, enabled
pcib0: matched entry for 0.27.INTA
pcib0: slot 27 INTA hardwired to IRQ 22
found-> vendor=0x8086, dev=0x283f, revid=0x02
bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0106, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2847, revid=0x02
bus=0, slot=28, func=4
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2849, revid=0x02
bus=0, slot=28, func=5
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTB
pcib0: slot 28 INTB hardwired to IRQ 17
found-> vendor=0x8086, dev=0x2830, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=3
map[20]: type 4, range 32, base 0000d800, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
found-> vendor=0x8086, dev=0x2831, revid=0x02
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=15
map[20]: type 4, range 32, base 0000d880, size 5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 19
found-> vendor=0x8086, dev=0x2832, revid=0x02
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=7
map[20]: type 4, range 32, base 0000dc00, size 5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x2833, revid=0x02
bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
map[20]: type 4, range 32, base 0000e000, size 5, enabled
pcib0: matched entry for 0.29.INTD
pcib0: slot 29 INTD hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2836, revid=0x02
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=3
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base febfbc00, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
found-> vendor=0x8086, dev=0x244e, revid=0xf2
bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2810, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2820, revid=0x02
bus=0, slot=31, func=2
class=01-01-8f, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=15
powerspec 3 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000ec00, size 3, enabled
map[14]: type 4, range 32, base 0000e880, size 2, enabled
map[18]: type 4, range 32, base 0000e800, size 3, enabled
map[1c]: type 4, range 32, base 0000e480, size 2, enabled
map[20]: type 4, range 32, base 0000e400, size 4, enabled
map[24]: type 4, range 32, base 0000e080, size 4, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 19
found-> vendor=0x8086, dev=0x283e, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=15
map[10]: type 1, range 32, base 00000000, size 8, memory disabled
map[20]: type 4, range 32, base 00000400, size 5, enabled
pcib0: matched entry for 0.31.INTC
pcib0: slot 31 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x2825, revid=0x02
bus=0, slot=31, func=5
class=01-01-85, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=15
powerspec 3 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000d480, size 3, enabled
map[14]: type 4, range 32, base 0000d400, size 2, enabled
map[18]: type 4, range 32, base 0000d080, size 3, enabled
map[1c]: type 4, range 32, base 0000d000, size 2, enabled
map[20]: type 4, range 32, base 0000cc00, size 4, enabled
map[24]: type 4, range 32, base 0000c880, size 4, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 19
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x8000-0x8fff
pcib1: memory decode 0xfa700000-0xfe7fffff
pcib1: prefetched decode 0xbfe00000-0xdfdfffff
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x10de, dev=0x0391, revid=0xa1
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 32, base fd000000, size 24, enabled
pcib1: requested memory range 0xfd000000-0xfdffffff: good
map[14]: type 3, range 64, base c0000000, size 28, enabled
pcib1: requested memory range 0xc0000000-0xcfffffff: good
map[1c]: type 1, range 64, base fc000000, size 24, enabled
pcib1: requested memory range 0xfc000000-0xfcffffff: good
map[24]: type 4, range 32, base 00008c00, size 7, enabled
pcib1: requested I/O range 0x8c00-0x8c7f: in range
pcib1: matched entry for 1.0.INTA
pcib1: slot 0 INTA hardwired to IRQ 16
pci1: <display, VGA> at device 0.0 (no driver attached)
pcm0: <Intel 82801H High Definition Audio Controller> mem
0xfebfc000-0xfebfffff irq 22 at device 27.0 on pci0
pcm0: TCSEL: 0x00 -> 0x00
pcm0: DMA Coherency: Uncacheable / vendor=0x8086
pcm0: hdac_mem_alloc: Unable to allocate memory resource
device_attach: pcm0 attach returned 6
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pcib2: secondary bus 4
pcib2: subordinate bus 4
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0xfff00000-0xfffff
pcib2: prefetched decode 0xdfe00000-0xdfefffff
pci4: <ACPI PCI bus> on pcib2
pci4: physical bus=4
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0xa000-0xafff
pcib3: memory decode 0xfe900000-0xfe9fffff
pcib3: prefetched decode 0xfff00000-0xfffff
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
found-> vendor=0x197b, dev=0x2363, revid=0x02
bus=3, slot=0, func=0
class=01-01-85, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000ac00, size 3, enabled
pcib3: requested I/O range 0xac00-0xac07: in range
map[14]: type 4, range 32, base 0000a880, size 2, enabled
pcib3: requested I/O range 0xa880-0xa883: in range
map[18]: type 4, range 32, base 0000a800, size 3, enabled
pcib3: requested I/O range 0xa800-0xa807: in range
map[1c]: type 4, range 32, base 0000a480, size 2, enabled
pcib3: requested I/O range 0xa480-0xa483: in range
map[20]: type 4, range 32, base 0000a400, size 4, enabled
pcib3: requested I/O range 0xa400-0xa40f: in range
map[24]: type 1, range 32, base fe9fe000, size 13, enabled
pcib3: requested memory range 0xfe9fe000-0xfe9fffff: good
pcib3: matched entry for 3.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 16
atapci0: <JMicron JMB363 SATA300 controller> port
0xac00-0xac07,0xa880-0xa883,0xa800-0xa807,0xa480-0xa483,0xa400-0xa40f mem
0xfe9fe000-0xfe9fffff irq 16 at device 0.0 on pci3
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xa400
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 49
atapci0: [MPSAFE]
atapci0: Reserved 0x2000 bytes for rid 0x24 type 3 at 0xfe9fe000
atapci0: AHCI Version 01.00 controller with 2 ports detected
ata2: <ATA channel 0> on atapci0
ata2: SATA connect status=00000000
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci0
ata3: SATA connect status=00000000
ata3: [MPSAFE]
ata4: <ATA channel 2> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xac00
atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xa880
ata4: reset tp1 mask=03 ostat0=10 ostat1=50
ata4: stat0=0x10 err=0x01 lsb=0x14 msb=0xeb
ata4: stat1=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=10 stat1=50 devices=0x6<ATAPI_MASTER,ATA_SLAVE>
ata4: [MPSAFE]
pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pcib4: secondary bus 2
pcib4: subordinate bus 2
pcib4: I/O decode 0x9000-0x9fff
pcib4: memory decode 0xfe800000-0xfe8fffff
pcib4: prefetched decode 0xfff00000-0xfffff
pci2: <ACPI PCI bus> on pcib4
pci2: physical bus=2
found-> vendor=0x11ab, dev=0x4364, revid=0x12
bus=2, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base fe8fc000, size 14, enabled
pcib4: requested memory range 0xfe8fc000-0xfe8fffff: good
map[18]: type 4, range 32, base 00009800, size 8, enabled
pcib4: requested I/O range 0x9800-0x98ff: in range
pcib4: matched entry for 2.0.INTA
pcib4: slot 0 INTA hardwired to IRQ 17
mskc0: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0x9800-0x98ff mem
0xfe8fc000-0xfe8fffff irq 17 at device 0.0 on pci2
mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xfe8fc000
mskc0: RAM buffer size : 128KB
mskc0: Port 0 : Rx Queue 96KB(0x00000000:0x00017fff)
mskc0: Port 0 : Tx Queue 32KB(0x00018000:0x0001ffff)
msk0: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x02> on
mskc0
msk0: bpf attached
msk0: Ethernet address: 00:1a:92:7e:09:63
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E1149 Gigabit PHY> on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX,
auto
ioapic0: routing intpin 17 (PCI IRQ 17) to vector 50
mskc0: [MPSAFE]
mskc0: [FAST]
uhci0: <UHCI (generic) USB controller> port 0xd800-0xd81f irq 23 at device
29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd800
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 51
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xd880-0xd89f irq 19 at device
29.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd880
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 52
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xdc00-0xdc1f irq 18 at device
29.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xdc00
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 53
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0xe000-0xe01f irq 16 at device
29.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe000
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebfbc00-0xfebfbfff irq 23
at device 29.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfebfbc00
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib5: secondary bus 5
pcib5: subordinate bus 5
pcib5: I/O decode 0xb000-0xbfff
pcib5: memory decode 0xfea00000-0xfeafffff
pcib5: prefetched decode 0xfff00000-0xfffff
pcib5: Subtractively decoded bridge.
pci5: <ACPI PCI bus> on pcib5
pci5: physical bus=5
found-> vendor=0x11ab, dev=0x4320, revid=0x14
bus=5, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
intpin=a, irq=15
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base feafc000, size 14, enabled
pcib5: requested memory range 0xfeafc000-0xfeafffff: good
map[14]: type 4, range 32, base 0000b800, size 8, enabled
pcib5: requested I/O range 0xb800-0xb8ff: in range
pcib5: matched entry for 5.4.INTA
pcib5: slot 4 INTA hardwired to IRQ 19
skc0: <Marvell Gigabit Ethernet> port 0xb800-0xb8ff mem
0xfeafc000-0xfeafffff irq 19 at device 4.0 on pci5
skc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xfeafc000
skc0: interrupt moderation is 100 us
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc0: PN: Yukon 88E8001
skc0: EC: Rev. 1.4
skc0: MN: Marvell
skc0: SN: AbCdEfG7E0549
skc0: chip ver = 0xb1
skc0: chip rev = 0x09
skc0: SK_EPROM0 = 0x10
skc0: SRAM size = 0x010000
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: bpf attached
sk0: Ethernet address: 00:1a:92:7e:05:49
miibus1: <MII bus> on sk0
e1000phy1: <Marvell 88E1011 Gigabit PHY> on miibus1
e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX,
auto
skc0: [MPSAFE]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH8 SATA300 controller> port
0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe40f,0xe080-0xe08f
irq 19 at device 31.2 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xe400
atapci1: [MPSAFE]
ata5: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xec00
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xe880
ata5: reset tp1 mask=03 ostat0=50 ostat1=00
ata5: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata5: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata5: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata5: [MPSAFE]
ata6: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xe800
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xe480
ata6: reset tp1 mask=03 ostat0=7f ostat1=7f
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata6: reset tp2 stat0=ff stat1=ff devices=0x0
ata6: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci2: <Intel ICH8 SATA300 controller> port
0xd480-0xd487,0xd400-0xd403,0xd080-0xd087,0xd000-0xd003,0xcc00-0xcc0f,0xc880-0xc88f
irq 19 at device 31.5 on pci0
atapci2: Reserved 0x10 bytes for rid 0x20 type 4 at 0xcc00
atapci2: [MPSAFE]
ata7: <ATA channel 0> on atapci2
atapci2: Reserved 0x8 bytes for rid 0x10 type 4 at 0xd480
atapci2: Reserved 0x4 bytes for rid 0x14 type 4 at 0xd400
ata7: reset tp1 mask=03 ostat0=7f ostat1=7f
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata7: reset tp2 stat0=ff stat1=ff devices=0x0
ata7: [MPSAFE]
ata8: <ATA channel 1> on atapci2
atapci2: Reserved 0x8 bytes for rid 0x18 type 4 at 0xd080
atapci2: Reserved 0x4 bytes for rid 0x1c type 4 at 0xd000
ata8: reset tp1 mask=03 ostat0=7f ostat1=7f
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata8: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata8: reset tp2 stat0=ff stat1=ff devices=0x0
ata8: [MPSAFE]
acpi_button0: <Power Button> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
acpi_hpet0: vend: 0x8086 rev: 0x1 num: 1 hz: 14318180 opts: leg_route
count_size
Timecounter "HPET" frequency 14318180 Hz quality 2000
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 54
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 55
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ex_isa_identify()
atkbdc: atkbdc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ahc_isa_probe 8: ioport 0x8c00 alloc failed
ahc_isa_probe 10: ioport 0xac00 alloc failed
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 56
ata0: [MPSAFE]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 57
ata1: [MPSAFE]
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ums0: vendor 0x1267 PS/2+USB Mouse, rev 1.10/23.23, addr 2, iclass 3/1
ums0: 5 buttons and Z dir.
Device configuration finished.
Reducing kern.maxvnodes 134330 -> 100000
procfs registered
lapic: Divisor 2, Frequency 133333733 hz
Timecounter "TSC" frequency 2400015564 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
rr232x: no controller detected.
ata4-slave: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: <TSSTcorpCD/DVDW SH-S182D/SB04> DVDR drive at ata4 as master
acd0: read 8269KB/s (8269KB/s) write 8269KB/s (8269KB/s), 2048KB buffer,
UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ad9: 152627MB <WDC WD1600JB-00REA0 20.00K20> at ata4-slave UDMA100
ad9: 312581808 sectors [4961616C/1H/63S] 16 sectors/interrupt 1 depth queue
ad9: JMicron check1 failed
ad9: Adaptec check1 failed
ad9: LSI (v3) check1 failed
ad9: LSI (v2) check1 failed
ad9: FreeBSD check1 failed
ata5-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad10: 152627MB <WDC WD1600AAJS-00PSA0 05.06H05> at ata5-master SATA150
ad10: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad9
GEOM: new disk ad10
ad10: Intel check1 failed
ad10: Adaptec check1 failed
ad10: LSI (v3) check1 failed
ad10: LSI (v2) check1 failed
ad10: FreeBSD check1 failed
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 4 to local APIC 1
ioapic0: Assigning ISA IRQ 9 to local APIC 0
ioapic0: Assigning ISA IRQ 14 to local APIC 1
ioapic0: Assigning ISA IRQ 15 to local APIC 0
ioapic0: Assigning PCI IRQ 16 to local APIC 1
ioapic0: Assigning PCI IRQ 17 to local APIC 0
ioapic0: Assigning PCI IRQ 18 to local APIC 1
ioapic0: Assigning PCI IRQ 19 to local APIC 0
ioapic0: Assigning PCI IRQ 23 to local APIC 1
Trying to mount root from ufs:/dev/ad9s1a
start_init: trying /sbin/init
More information about the freebsd-multimedia
mailing list