problem with tv + dga

Wed Apr 2 09:07:15 PST 2003

Hi.
I recently updated my mobo/cpu/mem from 
Abit ZM6/Celeron 366 at 550/256 to Abit KD7/Athlon XP2100+ TB B/512 DDR333.

After plugging everything in and rebooting, my tvcard hasn't worked properly.
(tvcard is hauppauge wintv primio)
problem is best described with a picture, ie. screenshot in
http://www.jukkis.net/snapshot3.png
IOW, only left side of image is rendered and only half of the lines.
problem occurs when image is resized to max, there is some problems also with 
a little smaller image. however, fxtv -disableDirectV works properly, but is 
just way too slow.

Any pointers what to change in BIOS or is there something to check in OS ?
I'm assuming this is a HW issue..

I already tried to load failsafe defaults in bios, and restrict my Geforce2 MX 
to AGP 2x mode, but that doesn't change anything.

I'm using NVidia's drivers, but also tried the nv driver from XFree86, same 
problem on both.
I had 5.0-Release when I updated my pc, since then I updated to -p6 which 
hasn't helped.

please cc any eventual replies, I'm unfortunately not on the list (for some 
reason subscribing didn't work, I tried several times when majordomo was in 
use, maybe I should try again now..)

And dmesg follows:
(notice the 'bktr' errors in the end of dmesg, maybe they are related)
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE-p6 #3: Sun Mar 23 23:50:24 CET 2003
    sjuke at sjukebox:/usr/RELENG_5_0/obj/usr/RELENG_5_0/src/sys/ATHLONXP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc05f4000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc05f40a8.
Preloaded elf module "/boot/kernel/nvidia.ko" at 0xc05f40f8.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05f41a4.
Timecounter "i8254"  frequency 1193182 Hz
CPU: AMD Athlon(tm) XP 2100+ (1734.07-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x681  Stepping = 1

Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM
OV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xffffffffc0400000<AMIE,DSP,3DNow!>
real memory  = 536805376 (511 MB)
avail memory = 515055616 (491 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: Other PM system enabled.
Using $PIR table, 11 entries at 0xc00fdea0
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
agp0: <VIA Generic host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 
o
n pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
nvidia0: <GeForce2 MX/MX 400> mem 0xe0000000-0xe7ffffff,0xec000000-0xecffffff 
ir
q 11 at device 0.0 on pci1
atapci0: <HighPoint HPT370 ATA100 controller> port 
0xa000-0xa0ff,0x9c00-0x9c03,0
x9800-0x9807,0x9400-0x9403,0x9000-0x9007 irq 10 at device 9.0 on pci0
ata2: at 0x9000 on atapci0
ata3: at 0x9800 on atapci0
bktr0: <BrookTree 878> mem 0xee020000-0xee020fff irq 7 at device 11.0 on pci0
bktr0: Hauppauge Model 61294 D129
bktr0: Hauppauge WinCast/TV, Philips PAL I tuner, remote control.
pci0: <multimedia> at device 11.1 (no driver attached)
pcm0: <Creative EMU10K1> port 0xa400-0xa41f irq 3 at device 12.0 on pci0
uhci0: <VIA 83C572 USB controller> port 0xac00-0xac1f irq 11 at device 16.0 on 
pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: Mustek Systems product 0xc420, rev 1.00/1.00, addr 2
uhci1: <VIA 83C572 USB controller> port 0xb000-0xb01f irq 10 at device 16.1 on 
pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xb400-0xb41f irq 3 at device 16.2 on 
pci0
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 16.3 (no driver attached)
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <VIA 8235 ATA133 controller> port 0xb800-0xb80f at device 17.1 on 
pci0
ata0: at 0x1f0 irq 14 on atapci1
ata1: at 0x170 irq 15 on atapci1
pcm1: <VIA VT8235> port 0xbc00-0xbcff irq 3 at device 17.5 on pci0
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xc000-0xc0ff mem 
0xee023000-0xee02
30ff irq 11 at device 18.0 on pci0
vr0: Ethernet address: 00:50:8d:47:46:14
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
Timecounters tick every 10.000 msec
ad0: 29198MB <SAMSUNG SV3063H> [59323/16/63] at ata0-master UDMA100
ar0: 152638MB <ATA RAID0 array> [19458/255/63] status: READY subdisks:
 0 READY ad4: 76319MB <WDC WD800JB-00CRA1> [155061/16/63] at ata2-master 
UDMA100
 1 READY ad6: 76319MB <WDC WD800JB-00CRA1> [155061/16/63] at ata3-master 
UDMA100
Opened disk ad4 -> 16
Opened disk ad4 -> 16
Opened disk ad6 -> 16
Opened disk ad6 -> 16
Mounting root from ufs:/dev/ar0s1a
cd0 at ata1 bus 0 target 0 lun 0
cd0: <LITE-ON LTR-24102B 5S57> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
bktr0: ioctl: 439: rows too large or not even.
bktr0: ioctl: 483: rows too large or not even.
bktr0: ioctl: 595: columns too large or not even.
bktr0: ioctl: 441: rows too large or not even.
bktr0: ioctl: 617: columns too large or not even.
bktr0: ioctl: 467: rows too large or not even.
bktr0: ioctl: 487: rows too large or not even.

uname -a:
FreeBSD sjukebox 5.0-RELEASE-p6 FreeBSD 5.0-RELEASE-p6 #3: Sun Mar 23 23:50:24 
CET 2003     
sjuke at sjukebox:/usr/RELENG_5_0/obj/usr/RELENG_5_0/src/sys/ATHLONXP  i386