Wierd X issue.

Jamie Bowden ragnar at sysabend.org
Thu Aug 14 05:56:08 PDT 2003


On Thu, 14 Aug 2003, Mark Santcroos wrote:

> On Thu, Aug 14, 2003 at 05:38:40AM -0700, Jamie Bowden wrote:
> > > And you don't have a /dev/kbd0, right?
> >
> > Correct.  There is no /dev/kbd0.
>
> Ok, clear.
>
> > 8:36am ghast  /dev %runas mknod kbd0 c 112 0
> > mknod: kbd0: No such file or directory
>
> mknod won't do you any good on devfs.
>
> Can you send a verbose dmesg and your kernel config?

Attached.

Jamie Bowden

-- 
"It was half way to Rivendell when the drugs began to take hold"
Hunter S Tolkien "Fear and Loathing in Barad Dur"
Iain Bowen <alaric at alaric.org.uk>

-------------- next part --------------
machine		i386
ident		ghast
maxusers	0
options 	INCLUDE_CONFIG_FILE     # Include this file in kernel
cpu		I686_CPU		# aka Pentium Pro(tm)
options 	COMPAT_43
options		SCHED_4BSD
options		COMPAT_FREEBSD4
options		_KPOSIX_PRIORITY_SCHEDULING
options 	SYSVSHM		# include support for shared memory
options 	SYSVSEM		# include support for semaphores
options 	SYSVMSG		# include support for message queues
options 	INET			#Internet communications protocols
options		INET6			#IPv6 communications protocols
options		IPSEC			#IP security
options		IPSEC_ESP		#IP security (crypto; define w/ IPSEC)
options		IPSEC_DEBUG		#debug for IP security
device		ether			#Generic Ethernet
device		loop			#Network loopback device
device		wlan			#802.11 support
device		ppp			#Point-to-point protocol
device		bpf			#Berkeley packet filter
device		gif			#IPv6 and IPv4 tunneling
device		faith			#for IPv6 and IPv4 translation
device		stf			#6to4 IPv6 over IPv4 encapsulation
device		tun	
options 	PPP_BSDCOMP		#PPP BSD-compress support
options 	PPP_DEFLATE		#PPP zlib/deflate/gzip support
options		PPP_FILTER		#enable bpf filtering (needs bpf)
options 	MROUTING		# Multicast routing
options 	FFS			#Fast filesystem
options 	SOFTUPDATES
device		random
device		scbus			#base SCSI code
device		da			#SCSI direct access devices (aka disks)
device		sa			#SCSI tapes
device		cd			#SCSI CD-ROMs
device		pass			#SCSI passthrough driver
device		pt			#SCSI processor type
options 	SCSI_DELAY=8000	# Be pessimistic about Joe SCSI device
device		pty		#Pseudo ttys
device		speaker		#Play IBM BASIC-style noises out your speaker
device		isa
device		atkbdc
device		atkbd
device		psm
device		vga
device		agp
options 	VESA
device		splash
device		sc
options 	MAXCONS=8		# number of virtual consoles
options		SC_PIXEL_MODE		# add support for the raster text mode
device		npx
device		ata
device		atadisk		# ATA disk drives
device		atapicd		# ATAPI CDROM drives
device		atapifd		# ATAPI floppy drives
device		atapist		# ATAPI tape drives
device		fdc
device		sio
device		apm
device		pmtimer
device		joy
device		pci
device		xl
device		miibus
device		pcm
device		midi
device		seq
device		cbb
device		pccard
device		cardbus
device		ppc
device		ppbus
device		lpt
device		vpo
device		firewire	# Firewire bus code
device		sbp		# SCSI over Firewire (Requires scbus and da)
device		fwe		# Ethernet over Firewire (non-standard!)
device		uhci
device		ohci
device		ehci
device		usb
device		ugen
device		uhid
device		ukbd
device		ulpt
device		umass
device		ums
-------------- next part --------------
N, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_tz0: <thermal zone> port 0x530-0x537 on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.PCI0.LNKA irq  11: [  9 10 11] low,level,sharable 0.31.0
\\_SB_.PCI0.LNKB irq   5: [  5  7] low,level,sharable 0.31.1
\\_SB_.PCI0.LNKC irq   3: [  9 10 11] low,level,sharable 0.31.2
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 0.31.3
\\_SB_.PCI0.LNKA irq  11: [  9 10 11] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq   5: [  5  7] low,level,sharable 0.1.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKA irq  11: [  9 10 11] low,level,sharable 0.31.0
\\_SB_.PCI0.LNKB irq   5: [  5  7] low,level,sharable 0.31.1
\\_SB_.PCI0.LNKC irq   3: [  9 10 11] low,level,sharable 0.31.2
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 0.31.3
\\_SB_.PCI0.LNKA irq  11: [  9 10 11] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq   5: [  5  7] low,level,sharable 0.1.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
	map[10]: type 3, range 32, base e8000000, size 26, enabled
found->	vendor=0x8086, dev=0x1130, revid=0x04
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x1131, revid=0x04
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0020, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x2448, revid=0x03
	bus=0, slot=30, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x244c, revid=0x03
	bus=0, slot=31, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000bfa0, size  4, enabled
found->	vendor=0x8086, dev=0x244a, revid=0x03
	bus=0, slot=31, func=1
	class=01-01-80, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000dce0, size  5, enabled
found->	vendor=0x8086, dev=0x2442, revid=0x03
	bus=0, slot=31, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=10
agp0: <Intel 82815 (i815 GMCH) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 36M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xc000-0xcfff
pcib1:   memory decode     0xfc000000-0xfdffffff
pcib1:   prefetched decode 0xe0000000-0xe7ffffff
---- initial configuration ------------------------
\\_SB_.PCI0.LNKA irq  11: [  9 10 11] low,level,sharable 1.0.0
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKA irq  11: [  9 10 11] low,level,sharable 1.0.0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
	map[10]: type 1, range 32, base fc000000, size 24, enabled
	map[14]: type 3, range 32, base e0000000, size 27, enabled
found->	vendor=0x10de, dev=0x0112, revid=0xb2
	bus=1, slot=0, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0027, statreg=0x02b0, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
nvidia0: <GeForce2 Go> mem 0xe0000000-0xe7ffffff,0xfc000000-0xfcffffff irq 11 at device 0.0 on pci1
pcib1: device nvidia0 requested decoded memory range 0xfc000000-0xfcffffff
pcib1: device nvidia0 requested decoded memory range 0xe0000000-0xe7ffffff
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   16
pcib2:   I/O decode        0xe000-0xffff
pcib2:   memory decode     0xf4000000-0xfbffffff
pcib2:   prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.15.0
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.15.1
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.15.2
\\_SB_.PCI0.LNKB irq   5: [  5  7] low,level,sharable 2.3.0
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.6.0
\\_SB_.PCI0.LNKC irq   3: [  9 10 11] low,level,sharable 2.6.1
\\_SB_.PCI0.LNKC irq   3: [  9 10 11] low,level,sharable 2.8.0
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.15.0
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.15.1
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.15.2
\\_SB_.PCI0.LNKB irq   5: [  5  7] low,level,sharable 2.3.0
\\_SB_.PCI0.LNKD irq  10: [  5  7 10 11] low,level,sharable 2.6.0
\\_SB_.PCI0.LNKC irq   3: [  9 10 11] low,level,sharable 2.6.1
\\_SB_.PCI0.LNKC irq   3: [  9 10 11] low,level,sharable 2.8.0
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
	map[10]: type 4, range 32, base 0000ec00, size  8, enabled
	map[14]: type 1, range 32, base f8ffe000, size 13, enabled
found->	vendor=0x125d, dev=0x1998, revid=0x10
	bus=2, slot=3, func=0
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=5
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 0000e800, size  8, enabled
	map[14]: type 1, range 32, base f8ffdc00, size  7, enabled
	map[18]: type 1, range 32, base f8ffd800, size  7, enabled
found->	vendor=0x10b7, dev=0x6055, revid=0x10
	bus=2, slot=6, func=0
	class=02-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x05 (1250 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 0000e400, size  8, enabled
	map[14]: type 1, range 32, base f8ffd400, size  8, enabled
	map[18]: type 1, range 32, base f8ffd000, size  7, enabled
found->	vendor=0x10b7, dev=0x1007, revid=0x10
	bus=2, slot=6, func=1
	class=07-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x05 (1250 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D2 D3  current D0
	map[10]: type 4, range 32, base 0000e080, size  7, enabled
	map[14]: type 1, range 32, base f8ffcc00, size  7, enabled
found->	vendor=0x10b7, dev=0x9200, revid=0x78
	bus=2, slot=8, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
	intpin=a, irq=3
	powerspec 2  supports D0 D1 D2 D3  current D0
found->	vendor=0x104c, dev=0xac42, revid=0x00
	bus=2, slot=15, func=0
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=255
	powerspec 2  supports D0 D1 D2 D3  current D0
found->	vendor=0x104c, dev=0xac42, revid=0x00
	bus=2, slot=15, func=1
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=255
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base f8ffc000, size 11, enabled
	map[14]: type 1, range 32, base f8ff8000, size 14, enabled
found->	vendor=0x104c, dev=0x8027, revid=0x00
	bus=2, slot=15, func=2
	class=0c-00-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0116, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D2 D3  current D0
pcm0: <ESS Technology Maestro3> port 0xec00-0xecff mem 0xf8ffe000-0xf8ffffff irq 5 at device 3.0 on pci2
pcib2: device pcm0 requested decoded I/O range 0xec00-0xecff
pcm0: <SigmaTel STAC9721/23 AC97 Codec (id = 0x83847609)>
pcm0: Codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features AMAP
pcm0: sndbuf_setmap 96a000, 1000; 0xdba03000 -> 96a000
pcm0: sndbuf_setmap 975000, 1000; 0xdba04000 -> 975000
pcm0: sndbuf_setmap 978000, 1000; 0xdba05000 -> 978000
pcm0: sndbuf_setmap 979000, 1000; 0xdba06000 -> 979000
pcm0: sndbuf_setmap 97b000, 1000; 0xdba07000 -> 97b000
xl0: <3Com 3c556 Fast Etherlink XL> port 0xe800-0xe8ff mem 0xf8ffd800-0xf8ffd87f,0xf8ffdc00-0xf8ffdc7f irq 10 at device 6.0 on pci2
pcib2: device xl0 requested decoded memory range 0xf8ffdc00-0xf8ffdc7f
xl0: using memory mapped I/O
pcib2: device xl0 requested decoded memory range 0xf8ffd800-0xf8ffd87f
xl0: Ethernet address: 00:04:76:4c:0d:94
xl0: media options word: 40
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
tdkphy0: <TDK 78Q2120 media interface> on miibus0
tdkphy0: OUI 0x00c039, model 0x0014, rev. 11
tdkphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
pci2: <simple comms> at device 6.1 (no driver attached)
xl1: <3Com 3c905C-TX Fast Etherlink XL> port 0xe080-0xe0ff mem 0xf8ffcc00-0xf8ffcc7f irq 3 at device 8.0 on pci2
pcib2: device xl1 requested decoded memory range 0xf8ffcc00-0xf8ffcc7f
xl1: using memory mapped I/O
xl1: Ethernet address: 00:06:5b:d0:0d:6e
xl1: media options word: a
xl1: found MII/AUTO
miibus1: <MII bus> on xl1
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: OUI 0x00105a, model 0x0000, rev. 0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl1: bpf attached
cbb0: <TI4451 PCI-CardBus Bridge> at device 15.0 on pci2
start (30000000) < sc->membase (f4000000)
end (ffffffff) > sc->memlimit (fbffffff)
pcib2: device cbb0 requested decoded memory range 0x30000000-0xffffffff
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: matched entry for 2.15.INTA (source \\_SB_.PCI0.LNKD)
pcib2: slot 15 INTA is routed to irq 10
cbb1: <TI4451 PCI-CardBus Bridge> at device 15.1 on pci2
start (30000000) < sc->membase (f4000000)
end (ffffffff) > sc->memlimit (fbffffff)
pcib2: device cbb1 requested decoded memory range 0x30000000-0xffffffff
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib2: matched entry for 2.15.INTA (source \\_SB_.PCI0.LNKD)
pcib2: slot 15 INTA is routed to irq 10
fwohci0: <Texas Instruments PCI4451> mem 0xf8ff8000-0xf8ffbfff,0xf8ffc000-0xf8ffc7ff irq 10 at device 15.2 on pci2
fwohci0: latency timer 32 -> 32.
fwohci0: cache size 8 -> 8.
pcib2: device fwohci0 requested decoded memory range 0xf8ffc000-0xf8ffc7ff
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 42:4f:c0:00:14:8b:94:21
fwohci0: resetting OHCI...done (loop=0)
fwohci0: phy read failed(1).
fwohci0: fwphy_rddata: loop=1, retry=1
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
if_fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 42:4f:c0:8b:94:21
fwe0: bpf attached
sbp0: <SBP2/SCSI over firewire> on firewire0
sbp_attach (cold=1)
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: loop=1, retry=0
fwohci0: fwphy_rddata: loop=1, retry=0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 UDMA100 controller> port 0xbfa0-0xbfaf at device 31.1 on pci0
ata0: pre reset mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 14 eb
ata0: after reset mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=09
ata0: at 0x1f0 irq 14 on atapci0
ata1: pre reset mask=03 ostat0=00 ostat2=00
ata1-master: ATAPI 00 00
ata1-slave: ATAPI 00 00
ata1: after reset mask=03 stat0=00 stat1=00
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0xdce0-0xdcff irq 10 at device 31.2 on pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Logitech USB Mouse, rev 1.10/6.20, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
unknown: not probed (disabled)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
speaker0 port 0x67,0x65,0x63,0x61 on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
unknown: not probed (disabled)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xcf000-0xcf7ff,0xce800-0xcefff,0xce000-0xce7ff,0xc0000-0xcdfff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
vpo0: can't connect to the drive
imm0: (disconnect) s1=0x38 s2=0x38, s3=0x38
imm0: (connect) s1=0x38 s2=0x38, s3=0x38
imm0: (connect) s1=0x38 s2=0x38, s3=0x38
imm0: (connect) s1=0x38 s2=0x38, s3=0x38
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <8 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x61 0x71 0x61 0x61
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x61 0x61 0x61 0x61
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x700ff
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 54 80 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounters tick every 10.000 msec
lo0: bpf attached
Linux ELF exec handler installed
IPsec: Initialized Security Association Processing.
fwohci0: BUS reset
sbp_post_busreset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
    ACPI-0293: *** Warning: Buffer created with zero length in AML
    ACPI-0293: *** Warning: Buffer created with zero length in AML
    ACPI-0293: *** Warning: Buffer created with zero length in AML
    ACPI-0293: *** Warning: Buffer created with zero length in AML
acpi_cmbat1: battery initialization start
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
bus_explore done
sbp_post_explore (sbp_cold=2)
start (30000000) < sc->membase (f4000000)
end (ffffffff) > sc->memlimit (fbffffff)
pcib2: device cardbus0 requested decoded memory range 0x30000000-0xffffffff
start (30000000) < sc->membase (f4000000)
end (ffffffff) > sc->memlimit (fbffffff)
pcib2: device cardbus0 requested decoded memory range 0x30000000-0xffffffff
found->	vendor=0x14e4, dev=0x4320, revid=0x02
	bus=4, slot=0, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0xa8 (5040 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
cardbus0: <network> at device 0.0 (no driver attached)
cbb0: CardBus card activation failed
ad0: success setting UDMA100 on Intel ICH2 chip
ad0: <IC25N030ATDA04-0/DA4OA70A> ATA-5 disk at ata0-master
ad0: 28615MB (58605120 sectors), 58140 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=12 dmamode=34 udmamode=69 cblid=1
GEOM: new disk ad0
ar: FreeBSD check1 failed
ata0-slave: piomode=12 dmamode=34 udmamode=-1 dmaflag=1
ata0-slave: success setting WDMA2 on Intel ICH2 chip
acd0: <Samsung CD-RW/DVD-ROM SN-308B/U003> CD-RW drive at ata0 as slave
acd0:  2048KB buffer, WDMA2
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd0: Writes: CD-R, CD-RW, test write, burnproof
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
[0] f:00 typ:23 s(CHS):0/1/1 e(CHS):1023/11/63 s:63 l:47873637
[1] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/15/63 s:47970090 l:10635030
[2] f:00 typ:28 s(CHS):1023/255/63 e(CHS):1023/5/63 s:47873700 l:96390
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 24511302144 end 24511334399
GEOM: Configure ad0s2, start 24560686080 length 5445135360 end 30005821439
GEOM: Configure ad0s3, start 24511334400 length 49351680 end 24560686079
GEOM: Configure ad0s2a, start 268435456 length 5176699904 end 5445135359
GEOM: Configure ad0s2b, start 0 length 268435456 end 268435455
GEOM: Configure ad0s2c, start 0 length 5445135360 end 5445135359
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
(probe3:sbp0:0:3:0): error 22
(probe3:sbp0:0:3:0): Unretryable Error
(probe4:sbp0:0:4:0): error 22
(probe4:sbp0:0:4:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
Mounting root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
splash: image decoder found: logo_saver
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
    ACPI-0293: *** Warning: Buffer created with zero length in AML
        -0166: *** Error: UtAllocate: Attempt to allocate zero bytes
acpi_cmbat0: battery initialization failed, giving up
acpi_cmbat1: battery initialization failed, giving up


More information about the freebsd-mobile mailing list