Solve: AR7161 USB

[Adrian Chadd]

Cool. There's some stuff you can put in hints to set on/off gpio
functions. Can you provide a diff to the right .hints file so it's
done at boot time?


-adrian

On 28 September 2016 at 23:46, Mori Hiroki <yamori813 at yahoo.co.jp> wrote:
> Hi
>
> Thanks for your advice. I can use USB on AR7161.
>
> # gpioctl 2 1
> # usbconfig
>
> ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=
> SAVE (0mA)
> ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr
> =SAVE (0mA)
> ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, cfg=0 md=HOST spd=FULL (
> 12Mbps) pwr=ON (100mA)
>
> Thanks.
>
> Hiroki Mori
>
> ----- Original Message -----
>> From: Adrian Chadd <adrian.chadd at gmail.com>
>> To: Mori Hiroki <yamori813 at yahoo.co.jp>
>> Cc: "freebsd-mips at freebsd.org" <freebsd-mips at freebsd.org>
>> Date: 2016/9/29, Thu 13:21
>> Subject: Re: AR7161 USB
>>
>> it could be something to do with port or phy power. check the default
>> gpio settings for your board; some don't enable usb phy power.
>>
>>
>> -a
>>
>>
>> On 28 September 2016 at 20:51, Mori Hiroki <yamori813 at yahoo.co.jp> wrote:
>>>  Hi.
>>>
>>>  on WZR-HP-G300NH(AR9132) OK
>>>
>>>
>>>
>>>  # usbconfig
>>>  ugen0.1: <EHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=HIGH
>> (480Mbps) pwr
>>>  =SAVE (0mA)
>>>  ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, cfg=0 md=HOST
>> spd=FULL (
>>>  12Mbps) pwr=ON (100mA)
>>>  #
>>>
>>>
>>>  on WZR-HP-AG300H(AR7161) NG
>>>
>>>  # usbconfig
>>>  ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=FULL
>> (12Mbps) pwr=
>>>  SAVE (0mA)
>>>  ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST spd=HIGH
>> (480Mbps) pwr
>>>  =SAVE (0mA)
>>>
>>>  I use ZRouter on build. I check hints file. I seem same as
>>>  sys/mips/conf/AP96.hints.
>>>
>>>  Thanks
>>>
>>>  Hiroki Mori
>>>
>>>
>>>
>>>  ----- Original Message -----
>>>>  From: Sean Bruno <sbruno at freebsd.org>
>>>>  To: freebsd-mips at freebsd.org
>>>>  Cc:
>>>>  Date: 2016/9/27, Tue 23:10
>>>>  Subject: Re: AR7161 USB
>>>>
>>>>
>>>>
>>>>  On 09/27/16 04:02, Mori Hiroki wrote:
>>>>>   Hi.
>>>>>
>>>>>   I try to use AR7161 target(WZR-HP-AG300H) on head today.
>>>>>   But I can't use USB this target. Device is probe on boot but
>> USB device
>>>>>   insert not detect device.
>>>>>
>>>>>   Any one use this ?
>>>>>
>>>>>   Regards.
>>>>>
>>>>>   Hiroki Mori
>>>>
>>>>  Is umass.ko loaded? (I assume you are using a USB storage device).
>>>>
>>>>  sean
>>>>
>>>  _______________________________________________
>>>  freebsd-mips at freebsd.org mailing list
>>>  https://lists.freebsd.org/mailman/listinfo/freebsd-mips
>>>  To unsubscribe, send any mail to
>> "freebsd-mips-unsubscribe at freebsd.org"
>>
> _______________________________________________
> freebsd-mips at freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-mips
> To unsubscribe, send any mail to "freebsd-mips-unsubscribe at freebsd.org"