ath0: could not map interrupt
Monthadar Al Jaberi
monthadar at gmail.com
Fri Jan 4 14:48:26 UTC 2013
Attached is two boot logs with debug on for resource manager of RB433AH
and RSPRO respectively. Also attached boot log from openWRT as a
reference (on RB433AH).
I installed an ath(4) in first slot in each board according to the marking on
each PCB. You will notice that RB433AH starts from slot 18.
I looked at openWRT and it seems they setup a special IRQ map for the RB4XX.
For RSPRO they don't seem to do anything special, and use the generic mappings
of three IRQ and slots 17 to 19.
While RB433AH lists the slots for the IRQ from slot 17 to 23.
RB433AH:
CPU platform: Atheros AR7161 rev 2
CPU Frequency=680 MHz
CPU DDR Frequency=340 MHz
CPU AHB Frequency=170 MHz
platform frequency: 680000000
arguments:
a0 = 00000008
a1 = a0871c00
a2 = 00000000
a3 = 00000000
Cmd line: console=ttyS0,115200 gpio=4031 HZ=340000000 mem=128M
kmac=D4:CA:6D:57:DC:D3 board=433 boot=1 mlc=2
Environment:
envp is invalid
Cache info:
picache_stride = 4096
picache_loopcount = 16
pdcache_stride = 4096
pdcache_loopcount = 8
cpu0: MIPS Technologies processor v116.147
MMU: Standard TLB, 16 entries
L1 i-cache: 4 ways of 512 sets, 32 bytes per line
L1 d-cache: 4 ways of 256 sets, 32 bytes per line
Config1=0x9ee3519e<PerfCount,WatchRegs,MIPS16,EJTAG>
Config3=0x20
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2013 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.0-CURRENT #172: Fri Jan 4 16:40:48 CET 2013
root at mechy:/usr/obj/mips.mips/usr/src/sys/RB433AH_MFS mips
WARNING: WITNESS option enabled, expect reduced performance.
MEMGUARD DEBUGGING ALLOCATOR INITIALIZED:
MEMGUARD map base: 0xc0400000
MEMGUARD map limit: 0xc6a67000
MEMGUARD map size: 104860 KBytes
real memory = 134217728 (131072K bytes)
avail memory = 123133952 (117MB)
random device not loaded; using insecure entropy
wlan: mac acl policy registered
rman_manage_region: <Hardware IRQs> request: start 0, end 0x5
rman_manage_region: <Memory addresses> request: start 0, end 0xffffffff
nexus0: <MIPS32 root nexus>
clock0: <Generic MIPS32 ticker> on nexus0
rman_reserve_resource_bound: <Hardware IRQs> request: [0x5, 0x5],
length 0x1, flags 2, device clock0
considering [0, 0x5]
truncated region: [0x5, 0x5]; size 0x1 (requested 0x1)
candidate region: [0x5, 0x5], size 0x1
allocating at the end
Timecounter "MIPS32" frequency 340000000 Hz quality 800
Event timer "MIPS32" frequency 340000000 Hz quality 800
apb0 at irq 4 on nexus0
rman_manage_region: <APB memory window> request: start 0x18000000, end
0x1dffffff
rman_manage_region: <APB IRQ> request: start 0, end 0x7
rman_reserve_resource_bound: <Hardware IRQs> request: [0x4, 0x4],
length 0x1, flags 6, device apb0
considering [0, 0x4]
truncated region: [0x4, 0x4]; size 0x1 (requested 0x1)
candidate region: [0x4, 0x4], size 0x1
allocating at the end
rman_reserve_resource_bound: <APB memory window> request: [0x18020003,
0x1802001a], length 0x18, flags 2, device uart0
considering [0x18000000, 0x1dffffff]
truncated region: [0x18020003, 0x1802001a]; size 0x18 (requested 0x18)
candidate region: [0x18020003, 0x1802001a], size 0x18
splitting region in three parts: [0x18000000, 0x18020002];
[0x18020003, 0x1802001a]; [0x1802001b, 0x1dffffff]
rman_reserve_resource_bound: <APB memory window> request: [0x18020003,
0x1802001a], length 0x18, flags 2, device uart0
considering [0x18000000, 0x1dffffff]
truncated region: [0x18020003, 0x1802001a]; size 0x18 (requested 0x18)
candidate region: [0x18020003, 0x1802001a], size 0x18
splitting region in three parts: [0x18000000, 0x18020002];
[0x18020003, 0x1802001a]; [0x1802001b, 0x1dffffff]
uart0: <16550 or compatible> on apb0
rman_reserve_resource_bound: <APB memory window> request: [0x18020003,
0x1802001a], length 0x18, flags 2, device uart0
considering [0x18000000, 0x1dffffff]
truncated region: [0x18020003, 0x1802001a]; size 0x18 (requested 0x18)
candidate region: [0x18020003, 0x1802001a], size 0x18
splitting region in three parts: [0x18000000, 0x18020002];
[0x18020003, 0x1802001a]; [0x1802001b, 0x1dffffff]
rman_reserve_resource_bound: <APB IRQ> request: [0x3, 0x3], length
0x1, flags 6, device uart0
considering [0, 0x7]
truncated region: [0x3, 0x3]; size 0x1 (requested 0x1)
candidate region: [0x3, 0x3], size 0x1
splitting region in three parts: [0, 0x2]; [0x3, 0x3]; [0x4, 0x7]
uart0: console (115200,n,8,1)
ehci0: <AR71XX Integrated USB 2.0 controller> at mem
0x1b000000-0x1bffffff irq 1 on nexus0
rman_reserve_resource_bound: <Memory addresses> request: [0x1b000000,
0x1bffffff], length 0x1000000, flags 2, device ehci0
considering [0, 0xffffffff]
truncated region: [0x1b000000, 0x1bffffff]; size 0x1000000 (requested 0x1000000)
candidate region: [0x1b000000, 0x1bffffff], size 0x1000000
splitting region in three parts: [0, 0x1affffff]; [0x1b000000,
0x1bffffff]; [0x1c000000, 0xffffffff]
rman_reserve_resource_bound: <Hardware IRQs> request: [0x1, 0x1],
length 0x1, flags 2, device ehci0
considering [0, 0x3]
truncated region: [0x1, 0x1]; size 0x1 (requested 0x1)
candidate region: [0x1, 0x1], size 0x1
splitting region in three parts: [0, 0]; [0x1, 0x1]; [0x2, 0x3]
usbus0: set host controller mode
usbus0: EHCI version 1.0
usbus0: set host controller mode
usbus0 on ehci0
pcib0 at irq 0 on nexus0
rman_manage_region: <ar71xx PCI memory window> request: start
0x10000000, end 0x16ffffff
rman_manage_region: <ar71xx PCI IRQs> request: start 0, end 0x2
rman_reserve_resource_bound: <Hardware IRQs> request: [0, 0], length
0x1, flags 6, device pcib0
considering [0, 0]
truncated region: [0, 0]; size 0x1 (requested 0x1)
candidate region: [0, 0], size 0x1
candidate region is entire chunk
pci0: <PCI bus> on pcib0
ath0: <Atheros 5413> irq 1 at device 18.0 on pci0
rman_reserve_resource_bound: <ar71xx PCI memory window> request: [0,
0xffffffff], length 0x10000, flags 16384, device ath0
considering [0x10000000, 0x16ffffff]
truncated region: [0x10000000, 0x16ffffff]; size 0x7000000 (requested 0x10000)
candidate region: [0x10000000, 0x16ffffff], size 0x7000000
allocating from the beginning
rman_reserve_resource_bound: <ar71xx PCI IRQs> request: [0x1, 0x1],
length 0x1, flags 6, device ath0
considering [0, 0x2]
truncated region: [0x1, 0x1]; size 0x1 (requested 0x1)
candidate region: [0x1, 0x1], size 0x1
splitting region in three parts: [0, 0]; [0x1, 0x1]; [0x2, 0x2]
ath0: AR5413 mac 10.5 RF5413 phy 6.1
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0063
arge0: <Atheros AR71xx built-in ethernet interface> at mem
0x19000000-0x19000fff irq 2 on nexus0
rman_reserve_resource_bound: <Memory addresses> request: [0x19000000,
0x19000fff], length 0x1000, flags 6, device arge0
considering [0, 0x1affffff]
truncated region: [0x19000000, 0x19000fff]; size 0x1000 (requested 0x1000)
candidate region: [0x19000000, 0x19000fff], size 0x1000
splitting region in three parts: [0, 0x18ffffff]; [0x19000000,
0x19000fff]; [0x19001000, 0x1affffff]
rman_reserve_resource_bound: <Hardware IRQs> request: [0x2, 0x2],
length 0x1, flags 6, device arge0
considering [0x2, 0x3]
truncated region: [0x2, 0x2]; size 0x1 (requested 0x1)
candidate region: [0x2, 0x2], size 0x1
allocating from the beginning
arge0: finishing attachment, phymask 0010, proxy null
miibus0: <MII bus> on arge0
ukphy1: <Generic IEEE 802.3u media interface> PHY 4 on miibus0
ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
arge0: Ethernet address: d4:ca:6d:57:dc:d4
arge1: <Atheros AR71xx built-in ethernet interface> at mem
0x1a000000-0x1a000fff irq 3 on nexus0
rman_reserve_resource_bound: <Memory addresses> request: [0x1a000000,
0x1a000fff], length 0x1000, flags 6, device arge1
considering [0x19001000, 0x1affffff]
truncated region: [0x1a000000, 0x1a000fff]; size 0x1000 (requested 0x1000)
candidate region: [0x1a000000, 0x1a000fff], size 0x1000
splitting region in three parts: [0x19001000, 0x19ffffff];
[0x1a000000, 0x1a000fff]; [0x1a001000, 0x1affffff]
rman_reserve_resource_bound: <Hardware IRQs> request: [0x3, 0x3],
length 0x1, flags 6, device arge1
considering [0x3, 0x3]
truncated region: [0x3, 0x3]; size 0x1 (requested 0x1)
candidate region: [0x3, 0x3], size 0x1
candidate region is entire chunk
arge1: finishing attachment, phymask 0000, proxy null
arge1: Ethernet address: d4:ca:6d:57:dc:d3
spi0: <AR71XX SPI> at mem 0x1f000000-0x1f00000f on nexus0
rman_reserve_resource_bound: <Memory addresses> request: [0x1f000000,
0x1f00000f], length 0x10, flags 2, device spi0
considering [0x1c000000, 0xffffffff]
truncated region: [0x1f000000, 0x1f00000f]; size 0x10 (requested 0x10)
candidate region: [0x1f000000, 0x1f00000f], size 0x10
splitting region in three parts: [0x1c000000, 0x1effffff];
[0x1f000000, 0x1f00000f]; [0x1f000010, 0xffffffff]
spibus0: <spibus bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 on spibus0
Unknown SPI flash device. Vendor: ef, device id: 3011
device_attach: mx25l0 attach returned 6
ar71xx_wdog0: <Atheros AR71XX watchdog timer> on nexus0
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
bootpc_init: wired to interface 'arge1'
Sending DHCP Discover packet from interface arge1 (d4:ca:6d:57:dc:d3)
RSPRO:
CPU platform: Atheros AR7161 rev 2
CPU Frequency=720 MHz
CPU DDR Frequency=360 MHz
CPU AHB Frequency=180 MHz
platform frequency: 720000000
arguments:
a0 = 00000002
a1 = 80050028
a2 = 80050000
a3 = 0000000a
Cmd line: ����������������������������������������������������������������������������������������������������
Environment:
memsize = 0x08000000
modetty0 = 0,n,8,1,hw
ethaddr = 00.15.6d.c8.c9.2c
board = RouterStation PRO
Cache info:
picache_stride = 4096
picache_loopcount = 16
pdcache_stride = 4096
pdcache_loopcount = 8
cpu0: MIPS Technologies processor v116.147
MMU: Standard TLB, 16 entries
L1 i-cache: 4 ways of 512 sets, 32 bytes per line
L1 d-cache: 4 ways of 256 sets, 32 bytes per line
Config1=0x9ee3519e<PerfCount,WatchRegs,MIPS16,EJTAG>
Config3=0x20
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2013 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.0-CURRENT #9: Fri Jan 4 16:52:15 CET 2013
root at mechy:/usr/obj/mips.mips/usr/src/sys/RSPRO_NFS mips
WARNING: WITNESS option enabled, expect reduced performance.
MEMGUARD DEBUGGING ALLOCATOR INITIALIZED:
MEMGUARD map base: 0xc0400000
MEMGUARD map limit: 0xc6a67000
MEMGUARD map size: 104860 KBytes
real memory = 134217728 (131072K bytes)
avail memory = 122871808 (117MB)
random device not loaded; using insecure entropy
rman_manage_region: <Hardware IRQs> request: start 0, end 0x5
rman_manage_region: <Memory addresses> request: start 0, end 0xffffffff
nexus0: <MIPS32 root nexus>
clock0: <Generic MIPS32 ticker> on nexus0
rman_reserve_resource_bound: <Hardware IRQs> request: [0x5, 0x5],
length 0x1, flags 2, device clock0
considering [0, 0x5]
truncated region: [0x5, 0x5]; size 0x1 (requested 0x1)
candidate region: [0x5, 0x5], size 0x1
allocating at the end
Timecounter "MIPS32" frequency 360000000 Hz quality 800
Event timer "MIPS32" frequency 360000000 Hz quality 800
apb0 at irq 4 on nexus0
rman_manage_region: <APB memory window> request: start 0x18000000, end
0x1dffffff
rman_manage_region: <APB IRQ> request: start 0, end 0x7
rman_reserve_resource_bound: <Hardware IRQs> request: [0x4, 0x4],
length 0x1, flags 6, device apb0
considering [0, 0x4]
truncated region: [0x4, 0x4]; size 0x1 (requested 0x1)
candidate region: [0x4, 0x4], size 0x1
allocating at the end
rman_reserve_resource_bound: <APB memory window> request: [0x18020003,
0x1802001a], length 0x18, flags 2, device uart0
considering [0x18000000, 0x1dffffff]
truncated region: [0x18020003, 0x1802001a]; size 0x18 (requested 0x18)
candidate region: [0x18020003, 0x1802001a], size 0x18
splitting region in three parts: [0x18000000, 0x18020002];
[0x18020003, 0x1802001a]; [0x1802001b, 0x1dffffff]
rman_reserve_resource_bound: <APB memory window> request: [0x18020003,
0x1802001a], length 0x18, flags 2, device uart0
considering [0x18000000, 0x1dffffff]
truncated region: [0x18020003, 0x1802001a]; size 0x18 (requested 0x18)
candidate region: [0x18020003, 0x1802001a], size 0x18
splitting region in three parts: [0x18000000, 0x18020002];
[0x18020003, 0x1802001a]; [0x1802001b, 0x1dffffff]
uart0: <16550 or compatible> on apb0
rman_reserve_resource_bound: <APB memory window> request: [0x18020003,
0x1802001a], length 0x18, flags 2, device uart0
considering [0x18000000, 0x1dffffff]
truncated region: [0x18020003, 0x1802001a]; size 0x18 (requested 0x18)
candidate region: [0x18020003, 0x1802001a], size 0x18
splitting region in three parts: [0x18000000, 0x18020002];
[0x18020003, 0x1802001a]; [0x1802001b, 0x1dffffff]
rman_reserve_resource_bound: <APB IRQ> request: [0x3, 0x3], length
0x1, flags 6, device uart0
considering [0, 0x7]
truncated region: [0x3, 0x3]; size 0x1 (requested 0x1)
candidate region: [0x3, 0x3], size 0x1
splitting region in three parts: [0, 0x2]; [0x3, 0x3]; [0x4, 0x7]
uart0: console (115200,n,8,1)
gpio0: <Atheros AR71XX GPIO driver> on apb0
rman_reserve_resource_bound: <APB memory window> request: [0x18040000,
0x18040fff], length 0x1000, flags 2, device gpio0
considering [0x1802001b, 0x1dffffff]
truncated region: [0x18040000, 0x18040fff]; size 0x1000 (requested 0x1000)
candidate region: [0x18040000, 0x18040fff], size 0x1000
splitting region in three parts: [0x1802001b, 0x1803ffff];
[0x18040000, 0x18040fff]; [0x18041000, 0x1dffffff]
rman_reserve_resource_bound: <APB IRQ> request: [0x2, 0x2], length
0x1, flags 6, device gpio0
considering [0, 0x2]
truncated region: [0x2, 0x2]; size 0x1 (requested 0x1)
candidate region: [0x2, 0x2], size 0x1
allocating at the end
gpio0: [GIANT-LOCKED]
gpio0: function_set: 0x0
gpio0: function_clear: 0x0
gpio0: gpio pinmask=0xff
gpioc0: <GPIO controller> on gpio0
gpiobus0: <GPIO bus> on gpio0
gpioled0: <GPIO led> at pin(s) 2 on gpiobus0
ehci0: <AR71XX Integrated USB 2.0 controller> at mem
0x1b000000-0x1bffffff irq 1 on nexus0
rman_reserve_resource_bound: <Memory addresses> request: [0x1b000000,
0x1bffffff], length 0x1000000, flags 2, device ehci0
considering [0, 0xffffffff]
truncated region: [0x1b000000, 0x1bffffff]; size 0x1000000 (requested 0x1000000)
candidate region: [0x1b000000, 0x1bffffff], size 0x1000000
splitting region in three parts: [0, 0x1affffff]; [0x1b000000,
0x1bffffff]; [0x1c000000, 0xffffffff]
rman_reserve_resource_bound: <Hardware IRQs> request: [0x1, 0x1],
length 0x1, flags 2, device ehci0
considering [0, 0x3]
truncated region: [0x1, 0x1]; size 0x1 (requested 0x1)
candidate region: [0x1, 0x1], size 0x1
splitting region in three parts: [0, 0]; [0x1, 0x1]; [0x2, 0x3]
usbus0: set host controller mode
usbus0: EHCI version 1.0
usbus0: set host controller mode
usbus0 on ehci0
pcib0 at irq 0 on nexus0
rman_manage_region: <ar71xx PCI memory window> request: start
0x10000000, end 0x16ffffff
rman_manage_region: <ar71xx PCI IRQs> request: start 0, end 0x2
rman_reserve_resource_bound: <Hardware IRQs> request: [0, 0], length
0x1, flags 6, device pcib0
considering [0, 0]
truncated region: [0, 0]; size 0x1 (requested 0x1)
candidate region: [0, 0], size 0x1
candidate region is entire chunk
pci0: <PCI bus> on pcib0
ath0: <Atheros 5413> irq 0 at device 17.0 on pci0
rman_reserve_resource_bound: <ar71xx PCI memory window> request: [0,
0xffffffff], length 0x10000, flags 16384, device ath0
considering [0x10000000, 0x16ffffff]
truncated region: [0x10000000, 0x16ffffff]; size 0x7000000 (requested 0x10000)
candidate region: [0x10000000, 0x16ffffff], size 0x7000000
allocating from the beginning
rman_reserve_resource_bound: <ar71xx PCI IRQs> request: [0, 0], length
0x1, flags 6, device ath0
considering [0, 0x2]
truncated region: [0, 0]; size 0x1 (requested 0x1)
candidate region: [0, 0], size 0x1
allocating from the beginning
ath0: AR5413 mac 10.5 RF5413 phy 6.1
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0063
arge0: <Atheros AR71xx built-in ethernet interface> at mem
0x19000000-0x19000fff irq 2 on nexus0
arge0: arge_attach: overriding MII mode to 'RGMII'
rman_reserve_resource_bound: <Memory addresses> request: [0x19000000,
0x19000fff], length 0x1000, flags 6, device arge0
considering [0, 0x1affffff]
truncated region: [0x19000000, 0x19000fff]; size 0x1000 (requested 0x1000)
candidate region: [0x19000000, 0x19000fff], size 0x1000
splitting region in three parts: [0, 0x18ffffff]; [0x19000000,
0x19000fff]; [0x19001000, 0x1affffff]
rman_reserve_resource_bound: <Hardware IRQs> request: [0x2, 0x2],
length 0x1, flags 6, device arge0
considering [0x2, 0x3]
truncated region: [0x2, 0x2]; size 0x1 (requested 0x1)
candidate region: [0x2, 0x2], size 0x1
allocating from the beginning
arge0: finishing attachment, phymask 0010, proxy null
miibus0: <MII bus> on arge0
ukphy0: <Generic IEEE 802.3u media interface> PHY 4 on miibus0
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseT-FDX, 1000baseT-FDX-master, auto
arge0: Ethernet address: 00:15:6d:c8:c9:2c
arge1: <Atheros AR71xx built-in ethernet interface> at mem
0x1a000000-0x1a000fff irq 3 on nexus0
arge1: arge_attach: overriding MII mode to 'RGMII'
rman_reserve_resource_bound: <Memory addresses> request: [0x1a000000,
0x1a000fff], length 0x1000, flags 6, device arge1
considering [0x19001000, 0x1affffff]
truncated region: [0x1a000000, 0x1a000fff]; size 0x1000 (requested 0x1000)
candidate region: [0x1a000000, 0x1a000fff], size 0x1000
splitting region in three parts: [0x19001000, 0x19ffffff];
[0x1a000000, 0x1a000fff]; [0x1a001000, 0x1affffff]
rman_reserve_resource_bound: <Hardware IRQs> request: [0x3, 0x3],
length 0x1, flags 6, device arge1
considering [0x3, 0x3]
truncated region: [0x3, 0x3]; size 0x1 (requested 0x1)
candidate region: [0x3, 0x3], size 0x1
candidate region is entire chunk
arge1: finishing attachment, phymask 0000, proxy null
arge1: Ethernet address: 00:15:6d:c8:c9:2d
spi0: <AR71XX SPI> at mem 0x1f000000-0x1f00000f on nexus0
rman_reserve_resource_bound: <Memory addresses> request: [0x1f000000,
0x1f00000f], length 0x10, flags 2, device spi0
considering [0x1c000000, 0xffffffff]
truncated region: [0x1f000000, 0x1f00000f]; size 0x10 (requested 0x10)
candidate region: [0x1f000000, 0x1f00000f], size 0x10
splitting region in three parts: [0x1c000000, 0x1effffff];
[0x1f000000, 0x1f00000f]; [0x1f000010, 0xffffffff]
spibus0: <spibus bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 on spibus0
mx25l0: mx25ll128, sector 65536 bytes, 256 sectors
ar71xx_wdog0: <Atheros AR71XX watchdog timer> on nexus0
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <Atheros> at usbus0
uhub0: <Atheros EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
g_dev_taste: make_dev_p() failed (gp->name=redboot/RedBoot config, error=22)
g_dev_taste: make_dev_p() failed (gp->name=redboot/FIS directory, error=22)
bootpc_init: wired to interface 'arge0'
Sending DHCP Discover packet from interface arge0 (00:15:6d:c8:c9:2c)
OpenWRT:
[ 0.000000] Linux version 3.3.8 (monthadar.aljaberi at bane) (gcc
version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #5 Fri
Dec 21 16:41:32 CET 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz,
Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 gpio=4031
HZ=340000000 mem=128M kmac=D4:CA:6D:57:DC:D3 board=433 boot=1 mlc=2
rootfstype=yaffs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000080
[ 0.000000] Readback ErrCtl register=00000080
[ 0.000000] Memory: 125360k/131072k available (2063k kernel code,
5712k reserved, 417k data, 1468k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] gpiochip_add: registered GPIOs 0 to 15 on device: ath79
[ 0.080000] MIPS: machine is MikroTik RouterBOARD 433/AH
[ 0.780000] registering PCI controller with io_map_base unset
[ 0.790000] bio: create slab <bio-0> at 0
[ 0.800000] PCI host bridge to bus 0000:00
[ 0.800000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[ 0.810000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.810000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[ 0.820000] pci 0000:00:12.0: using irq 40 for pin 1
[ 0.820000] Switching to clocksource MIPS
[ 0.830000] NET: Registered protocol family 2
[ 0.830000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.830000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.840000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.850000] TCP reno registered
[ 0.850000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.860000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.860000] NET: Registered protocol family 1
[ 2.330000] msgmni has been set to 244
[ 2.330000] io scheduler noop registered
[ 2.340000] io scheduler deadline registered (default)
[ 2.340000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.370000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 2.370000] console [ttyS0] enabled, bootconsole disabled
[ 2.370000] console [ttyS0] enabled, bootconsole disabled
[ 2.390000] gpiochip_add: registered GPIOs 32 to 40 on device: spi-rb4xx-cpld
[ 2.390000] m25p80 spi0.0: pm25lv512 (64 Kbytes)
[ 2.400000] Creating 4 MTD partitions on "spi0.0":
[ 2.400000] 0x000000000000-0x00000000b000 : "routerboot"
[ 2.410000] 0x00000000b000-0x00000000c000 : "hard_config"
[ 2.420000] 0x00000000d000-0x00000000f000 : "bios"
[ 2.420000] 0x00000000f000-0x000000010000 : "soft_config"
[ 2.430000] NAND flash driver for RouterBoard 4xx series version 0.2.0
[ 2.440000] NAND device: Manufacturer ID: 0xec, Chip ID: 0x76
(Samsung NAND 64MiB 3,3V 8-bit)
[ 2.450000] Scanning device for bad blocks
[ 2.610000] Bad eraseblock 947 at 0x000000ecc000
[ 2.640000] Bad eraseblock 1093 at 0x000001114000
[ 2.690000] Bad eraseblock 1353 at 0x000001524000
[ 2.730000] Bad eraseblock 1565 at 0x000001874000
[ 2.740000] Bad eraseblock 1566 at 0x000001878000
[ 2.860000] Bad eraseblock 2261 at 0x000002354000
[ 2.860000] Bad eraseblock 2262 at 0x000002358000
[ 2.870000] Bad eraseblock 2277 at 0x000002394000
[ 2.880000] Bad eraseblock 2278 at 0x000002398000
[ 2.880000] Bad eraseblock 2279 at 0x00000239c000
[ 2.890000] Bad eraseblock 2280 at 0x0000023a0000
[ 2.890000] Bad eraseblock 2283 at 0x0000023ac000
[ 2.900000] Bad eraseblock 2284 at 0x0000023b0000
[ 2.900000] Bad eraseblock 2286 at 0x0000023b8000
[ 2.910000] Bad eraseblock 2288 at 0x0000023c0000
[ 2.910000] Bad eraseblock 2289 at 0x0000023c4000
[ 2.920000] Bad eraseblock 2291 at 0x0000023cc000
[ 2.920000] Bad eraseblock 2293 at 0x0000023d4000
[ 2.920000] Bad eraseblock 2294 at 0x0000023d8000
[ 2.930000] Bad eraseblock 2299 at 0x0000023ec000
[ 2.940000] Bad eraseblock 2300 at 0x0000023f0000
[ 2.940000] Bad eraseblock 2303 at 0x0000023fc000
[ 2.950000] Bad eraseblock 2306 at 0x000002408000
[ 2.950000] Bad eraseblock 2307 at 0x00000240c000
[ 2.950000] Bad eraseblock 2308 at 0x000002410000
[ 2.960000] Bad eraseblock 2309 at 0x000002414000
[ 2.970000] Bad eraseblock 2335 at 0x00000247c000
[ 2.970000] Bad eraseblock 2336 at 0x000002480000
[ 2.980000] Bad eraseblock 2355 at 0x0000024cc000
[ 3.000000] Bad eraseblock 2429 at 0x0000025f4000
[ 3.000000] Bad eraseblock 2433 at 0x000002604000
[ 3.010000] Bad eraseblock 2436 at 0x000002610000
[ 3.010000] Bad eraseblock 2439 at 0x00000261c000
[ 3.020000] Bad eraseblock 2442 at 0x000002628000
[ 3.020000] Bad eraseblock 2443 at 0x00000262c000
[ 3.030000] Bad eraseblock 2446 at 0x000002638000
[ 3.030000] Bad eraseblock 2449 at 0x000002644000
[ 3.040000] Bad eraseblock 2453 at 0x000002654000
[ 3.040000] Bad eraseblock 2456 at 0x000002660000
[ 3.050000] Bad eraseblock 2457 at 0x000002664000
[ 3.050000] Bad eraseblock 2459 at 0x00000266c000
[ 3.060000] Bad eraseblock 2462 at 0x000002678000
[ 3.060000] Bad eraseblock 2465 at 0x000002684000
[ 3.070000] Bad eraseblock 2468 at 0x000002690000
[ 3.070000] Bad eraseblock 2470 at 0x000002698000
[ 3.080000] Bad eraseblock 2473 at 0x0000026a4000
[ 3.080000] Bad eraseblock 2475 at 0x0000026ac000
[ 3.090000] Bad eraseblock 2476 at 0x0000026b0000
[ 3.250000] Bad eraseblock 3371 at 0x0000034ac000
[ 3.380000] Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
[ 3.380000] 0x000000000000-0x000000040000 : "booter"
[ 3.390000] 0x000000040000-0x000000400000 : "kernel"
[ 3.390000] 0x000000400000-0x000004000000 : "rootfs"
[ 3.400000] mtd: partition "rootfs" set to be root filesystem
[ 3.410000] split_squashfs: no squashfs found in "NAND 64MiB 3,3V 8-bit"
[ 3.420000] IP17xx: Found IP175D at ag71xx-mdio.0:00
[ 3.420000] ag71xx_mdio: probed
[ 3.430000] eth0: Atheros AG71xx at 0xba000000, irq 5
[ 3.730000] ag71xx ag71xx.1: eth0: connected to PHY at
ag71xx-mdio.0:04 [uid=02430d80, driver=Generic PHY]
[ 3.740000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[ 4.060000] ag71xx ag71xx.0: eth1: connected to PHY at
ag71xx-mdio.0:00 [uid=02430d80, driver=IC+ IP17xx]
[ 4.070000] TCP cubic registered
[ 4.070000] NET: Registered protocol family 17
[ 4.070000] 8021q: 802.1Q VLAN Support v1.8
[ 4.080000] Freeing unused kernel memory: 1468k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
[ 5.730000] eth0: link up (100Mbps/Full duplex)
- regular preinit -
[ 7.700000] eth0: link down
- init -
[ 7.870000] Compat-drivers backport release:
compat-drivers-2012-09-04-2-gddac993
[ 7.880000] Backport based on wireless-testing.git master-2012-09-07
[ 7.890000] compat.git: wireless-testing.git
[ 7.910000] cfg80211: Calling CRDA to update world regulatory domain
[ 7.910000] cfg80211: World regulatory domain updated:
[ 7.920000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 7.930000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 7.930000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz),
(300 mBi, 2000 mBm)
[ 7.940000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(300 mBi, 2000 mBm)
[ 7.950000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 7.960000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 8.030000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
[ 8.040000] ath5k 0000:00:12.0: registered as 'phy0'
[ 8.690000] ath5k: phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61)
[ 8.690000] cfg80211: Calling CRDA for country: US
[ 8.700000] cfg80211: Regulatory domain changed to country: US
[ 8.700000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 8.710000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(300 mBi, 2700 mBm)
[ 8.720000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz),
(300 mBi, 1700 mBm)
[ 8.730000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 8.740000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 8.740000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 8.750000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz),
(300 mBi, 3000 mBm)
[ 8.790000] PPP generic driver version 2.4.2
[ 8.820000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.900000] NET: Registered protocol family 24
[ 8.910000] nf_conntrack version 0.5.0 (1981 buckets, 7924 max)
Please press Enter to activate this console. [ 10.870000] device
eth1 entered promiscuous mode
[ 12.060000] eth1: link up (100Mbps/Full duplex)
[ 12.060000] br-lan: port 1(eth1) entered forwarding state
[ 12.070000] br-lan: port 1(eth1) entered forwarding state
[ 12.760000] eth0: link up (100Mbps/Full duplex)
[ 14.070000] br-lan: port 1(eth1) entered forwarding state
On Fri, Jan 4, 2013 at 5:59 AM, Adrian Chadd <adrian at freebsd.org> wrote:
> ... wow. How the hell is that happening?!
>
>
>
>
> Adrian
>
>
> On 3 January 2013 20:54, Monthadar Al Jaberi <monthadar at gmail.com> wrote:
>> Maybe this is the root of the problem.
>>
>> On RSPRO the PCI start slot enumerating from 17. While RB433AH start
>> from 18. That can explain why Slot 20 of RB433AH won't even attach
>> (AR7161 only has 3 slots, slot 17 to 19). That can also explain why I
>> get device_timeout on slot 18 and 19 cause they are miss aligned. And
>> don't see any interrupts from ath(4) when enabling interrupt
>> debugging.
>>
>> I will keep digging into why they won't start enumerating correct.
>>
>> br,
>>
>> On Fri, Jan 4, 2013 at 2:28 AM, Monthadar Al Jaberi <monthadar at gmail.com> wrote:
>>> Hi,
>>>
>>> I am wondering if anyone can confirm that any ath5k (preferably
>>> AR5413) series miniPCI wifi works on RB433/AH/UAH.
>>>
>>> Thank you in advance
>>>
>>> On Wed, Jan 2, 2013 at 10:29 PM, Monthadar Al Jaberi
>>> <monthadar at gmail.com> wrote:
>>>> On Wed, Jan 2, 2013 at 9:43 PM, Adrian Chadd <adrian at freebsd.org> wrote:
>>>>> ... sounds like a definite interrupt routing issue.
>>>>>
>>>>> Who's been knee deep in the interrupt handling code in MIPS lately? Grrr.
>>>>> I know there's been some FDT work in MIPS and that's touched some
>>>>> interrupt code.. maybe that's interfering?
>>>>
>>>> I am not sure, I just re-compiled my kernel for RSPRO and it seems to work.
>>>>
>>>> I install openwrt on rb433ah and ath0 associated ok. and I could ping
>>>> between RSPRO(FreeBSD) and RB433AH(Openwrt). RSPRO and non working
>>>> RB433AH running same kernel r243866.
>>>>
>>>> Attached is my kernel config & hints. ( I am "playing around" with the
>>>> ar71xx_spi but that should not effect the pci code, I hope).
>>>>
>>>> #
>>>> # AR71XX -- Kernel configuration file for FreeBSD/MIPS for Atheros 71xx systems
>>>> #
>>>> # This includes all the common drivers for the AR71XX boards along with
>>>> # the usb, net80211 and atheros driver code.
>>>> #
>>>> # $FreeBSD$
>>>> #
>>>>
>>>> machine mips mips
>>>> ident RB433AH_MFS
>>>> cpu CPU_MIPS4KC
>>>> makeoptions KERNLOADADDR=0x80050000
>>>> options HZ=1000
>>>> options HWPMC_HOOKS
>>>>
>>>> files "../atheros/files.ar71xx"
>>>>
>>>> # For now, hints are per-board.
>>>>
>>>> hints "RB433AH.hints"
>>>>
>>>> makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
>>>>
>>>> # Build these as modules so small platform builds will have the
>>>> # modules already built.
>>>> makeoptions MODULES_OVERRIDE="random gpio ar71xx if_gif if_gre
>>>> if_bridge bridgestp usb wlan wlan_xauth wlan_acl wlan_wep wlan_tkip
>>>> wlan_ccmp wlan_rssadapt wlan_amrr ath ath_pci"
>>>>
>>>> options DDB
>>>> options KDB
>>>>
>>>> options SCHED_4BSD #4BSD scheduler
>>>> options INET #InterNETworking
>>>> #options INET6 # IPv6
>>>>
>>>> # options NFS_CL #Network Filesystem Client
>>>>
>>>> options PSEUDOFS #Pseudo-filesystem framework
>>>> options _KPOSIX_PRIORITY_SCHEDULING #Posix P1003_1B real-time extensions
>>>>
>>>> # options NFS_LEGACYRPC
>>>> # Debugging for use in -current
>>>> options INVARIANTS
>>>> options INVARIANT_SUPPORT
>>>> options WITNESS
>>>> options WITNESS_SKIPSPIN
>>>> options DEBUG_REDZONE
>>>> options DEBUG_MEMGUARD
>>>>
>>>> options FFS #Berkeley Fast Filesystem
>>>> # options SOFTUPDATES #Enable FFS soft updates support
>>>> # options UFS_ACL #Support for access control lists
>>>> # options UFS_DIRHASH #Improve performance on big
>>>> directories
>>>> # options MSDOSFS # Read MSDOS filesystems; useful for USB/CF
>>>>
>>>> device pci
>>>> device ar71xx_pci
>>>>
>>>> # RTC - requires hackery in the spibus code to work
>>>> device pcf2123_rtc
>>>>
>>>> # GEOM modules
>>>> device geom_redboot # to get access to the SPI flash partitions
>>>> device geom_uzip # compressed in-memory filesystem hackery!
>>>> device geom_map
>>>> options GEOM_UZIP
>>>>
>>>> # NANDFS
>>>> options NANDFS
>>>>
>>>> ## Boot from the first MFS uzip
>>>> #options ROOTDEVNAME=\"ufs:md0.uzip\"
>>>> #options MD_ROOT
>>>> #options MD_ROOT_SIZE="9000"
>>>>
>>>> # Boot from NFS
>>>> options NFSLOCKD #Network Lock Manager
>>>> options NFSCLIENT #Network Filesystem Client
>>>> options NFS_ROOT
>>>>
>>>> options BOOTP
>>>> options BOOTP_NFSROOT
>>>> options BOOTP_NFSV3
>>>> options BOOTP_WIRED_TO=arge1
>>>> options BOOTP_COMPAT
>>>> options ROOTDEVNAME=\"nfs:172.16.0.101:/usr/obj/rb433ah/nfs\"
>>>>
>>>>
>>>> # 802.11 framework
>>>> options IEEE80211_DEBUG
>>>> options IEEE80211_ALQ
>>>> options IEEE80211_SUPPORT_MESH
>>>> # This option is currently broken for if_ath_tx.
>>>> options IEEE80211_SUPPORT_TDMA
>>>> options IEEE80211_AMPDU_AGE
>>>> device wlan # 802.11 support
>>>> device wlan_wep # 802.11 WEP support
>>>> device wlan_ccmp # 802.11 CCMP support
>>>> device wlan_tkip # 802.11 TKIP support
>>>> device wlan_xauth # 802.11 hostap support
>>>> device wlan_acl # 802.11 ACL support
>>>>
>>>> # Atheros wireless NICs
>>>> device ath # Atheros interface support
>>>> device ath_pci # Atheros PCI/Cardbus bus
>>>> options ATH_DEBUG
>>>> options ATH_DIAGAPI
>>>> options ATH_ENABLE_11N
>>>> options AH_DEBUG
>>>> options AH_DEBUG_ALQ
>>>> options ALQ
>>>> device ath_hal
>>>> option AH_SUPPORT_AR5416
>>>> device ath_rate_sample
>>>> option AH_RXCFG_SDMAMW_4BYTES
>>>> option AH_AR5416_INTERRUPT_MITIGATION
>>>> # There's no DFS radar detection support yet so this won't actually
>>>> # detect radars. It however does enable the rest of the channel change
>>>> # machinery so DFS can be debugged.
>>>> option ATH_ENABLE_DFS
>>>>
>>>> device mii
>>>> device arge
>>>> #options ARGE_DEBUG # Enable if_arge debugging for now
>>>>
>>>> #device usb
>>>> #options USB_EHCI_BIG_ENDIAN_DESC # handle big-endian byte order
>>>> #options USB_DEBUG
>>>> #options USB_HOST_ALIGN=32 # AR71XX (MIPS in general?) requires this
>>>> #device ehci
>>>>
>>>> device scbus
>>>> #device umass
>>>> device da
>>>>
>>>> device rb4xx
>>>>
>>>> # On-board SPI flash
>>>> device spibus
>>>> device ar71xx_spi
>>>> device mmc
>>>> device mmcsd
>>>> device mmcspi
>>>> device mx25l
>>>> device nand
>>>> device ar71xx_wdog
>>>>
>>>> device uart
>>>> device uart_ar71xx
>>>>
>>>> device loop
>>>> device ether
>>>> device md
>>>> device bpf
>>>> device random
>>>> device if_bridge
>>>> device gif # ip[46] in ip[46] tunneling protocol
>>>> device gre # generic encapsulation - only for IPv4 in IPv4 though atm
>>>>
>>>> # Enable GPIO
>>>> device gpio
>>>> device gpioled
>>>>
>>>> options AR71XX_ROUTERBOOT
>>>>
>>>>
>>>> # $FreeBSD$
>>>> hint.apb.0.at="nexus0"
>>>> hint.apb.0.irq=4
>>>>
>>>> # uart0
>>>> hint.uart.0.at="apb0"
>>>> # see atheros/uart_cpu_ar71xx.c why +3
>>>> hint.uart.0.maddr=0x18020003
>>>> hint.uart.0.msize=0x18
>>>> hint.uart.0.irq=3
>>>>
>>>> #ohci
>>>> #hint.ohci.0.at="apb0"
>>>> #hint.ohci.0.maddr=0x1c000000
>>>> #hint.ohci.0.msize=0x01000000
>>>> #hint.ohci.0.irq=6
>>>>
>>>> #ehci
>>>> #hint.ehci.0.at="nexus0"
>>>> #hint.ehci.0.maddr=0x1b000000
>>>> #hint.ehci.0.msize=0x01000000
>>>> #hint.ehci.0.irq=1
>>>>
>>>> # pci
>>>> hint.pcib.0.at="nexus0"
>>>> hint.pcib.0.irq=0
>>>>
>>>> hint.arge.0.at="nexus0"
>>>> hint.arge.0.maddr=0x19000000
>>>> hint.arge.0.msize=0x1000
>>>> hint.arge.0.irq=2
>>>> # PHY4 = 1 << 4
>>>> hint.arge.0.phymask=0x10
>>>> # Uncomment this hint for RS (not PRO)
>>>> # PHY20 = 1 << 20
>>>> # hint.arge.0.phymask=0x100000
>>>> hint.ukphy.0.at="miibus0"
>>>>
>>>> hint.arge.1.at="nexus0"
>>>> hint.arge.1.maddr=0x1a000000
>>>> hint.arge.1.msize=0x1000
>>>> hint.arge.1.irq=3
>>>> # PHY1, PHY2, PHY3
>>>> hint.arge.1.phymask=0x00
>>>> # should be 100 for RS
>>>> #hint.arge.1.media=100
>>>> #hint.arge.1.fduplex=1
>>>> # Uncomment this hint for RS (not PRO)
>>>> # hint.arge.1.phymask=70000
>>>>
>>>> # SPI flash
>>>> hint.spi.0.at="nexus0"
>>>> hint.spi.0.maddr=0x1f000000
>>>> hint.spi.0.msize=0x10
>>>>
>>>> hint.mx25l.0.at="spibus0"
>>>> hint.mx25l.0.cs=1
>>>>
>>>> hint.rb_cpldbus.0.at="spibus0"
>>>> hint.rb_cpldbus.0.cs=1
>>>> #
>>>> hint.onand.0.at="nandbus0"
>>>> hint.lnand.0.at="nandbus0"
>>>> hint.snand.0.at="nandbus0"
>>>>
>>>> hint.flash.0.at="nand0"
>>>> hint.flash.0.size="0x40000"
>>>> hint.flash.0.offset="0"
>>>> hint.flash.0.name="bootloader"
>>>> hint.flash.1.at="nand0"
>>>> hint.flash.1.size="0x3c0000"
>>>> hint.flash.1.offset="0x40000"
>>>> hint.flash.1.name="kernelfs"
>>>> hint.flash.2.at="nand0"
>>>> hint.flash.2.size="0"
>>>> hint.flash.2.offset="0x400000"
>>>> hint.flash.2.name="rootfs"
>>>>
>>>> hint.ar71xx_gpio.0.at="nexus0"
>>>>
>>>> #hint.rb_nandbusy.0.at="gpiobus0"
>>>>
>>>> hint.mmcspi.0.at="spibus0"
>>>> hint.mmcspi.0.cs=2
>>>>
>>>> # Watchdog
>>>> hint.ar71xx_wdog.0.at="nexus0"
>>>>
>>>>
>>>> br,
>>>>
>>>>>
>>>>>
>>>>> Adrian
>>>>>
>>>>>
>>>>> On 2 January 2013 12:40, Monthadar Al Jaberi <monthadar at gmail.com> wrote:
>>>>>> I tested some more. First I changed the miniPCI slot. Now boot looks like this:
>>>>>>
>>>>>> pcib0 at irq 0 on nexus0
>>>>>> pci0: <PCI bus> on pcib0
>>>>>> ath0: <Atheros 5413> irq 2 at device 19.0 on pci0
>>>>>> ath0: AR5413 mac 10.5 RF5413 phy 6.1
>>>>>> ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0063
>>>>>>
>>>>>>
>>>>>> Then I created a hostap. But none of my other devices sees it (laptop, iphone).
>>>>>>
>>>>>> A scan results in:
>>>>>>
>>>>>> # ifconfig wlan0 scan
>>>>>> wlan0: ieee80211_scanreq: flags 0x1b duration 0x7fffffff mindwell 0
>>>>>> maxdwell 0 nssid 0
>>>>>> wlan0: start_scan_locked: active scan, duration 2147483647 mindwell 0
>>>>>> maxdwell 0, desired mode 11g, append, nopick, once
>>>>>> wlan0: scan set 11g dwell min 200ms max 200ms
>>>>>> wlan0: scan_task: chan 11g -> 11g [active, dwell min 200ms max 200ms]
>>>>>> wlan0: ieee80211_ref_node (ieee80211_send_probereq:1822)
>>>>>> 0xc6f27000<00:15:6d:67:21:8d> refcnt 4
>>>>>> wlan0: send probe req on channel 11 bssid ff:ff:ff:ff:ff:ff ssid ""
>>>>>> wlan0: scan_task: done, [ticks 2657909, dwell min 200 scanend 2150141333]
>>>>>> wlan0: notify scan done
>>>>>> root at rb433ah:~ # ath0: device timeout
>>>>>>
>>>>>> And when I try to ping a random IP address I get the following.
>>>>>> Interesting is that it seems to "bail out" when it tries to send
>>>>>> probe_resp (last in output):
>>>>>> $ ping -c 1 172.168.3.2
>>>>>> PING 172.168.3.2 (172.168.3.2): 56 data bytes
>>>>>> ath0: device timeout
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 46
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 13
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 00:11:50:4d:c5:08 rssi 8
>>>>>> wlan0: [00:11:50:4d:c5:08] discard unhandled information element, id 47, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 40
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 12
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [94:0c:6d:ad:61:18] discard frame, not to bss
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 13
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 48
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received probe_req from 00:16:cf:3c:f7:7f rssi 2
>>>>>> [00:16:cf:3c:f7:7f] discard probe_req frame, ssid mismatch:
>>>>>> 0x9ccca48e6a3b0c7f661c24413d7b9e54c5e59ddbe0c2bd96a2e65410b662f71a
>>>>>> wlan0: received probe_req from 00:16:cf:3c:f7:7f rssi 5
>>>>>> [00:16:cf:3c:f7:7f] discard probe_req frame, ssid mismatch: "default"
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 12
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received probe_req from 00:16:cf:3c:f7:7f rssi 4
>>>>>> [00:16:cf:3c:f7:7f] discard probe_req frame, ssid mismatch: "default"
>>>>>> wlan0: received beacon from 00:11:50:4d:c5:08 rssi 9
>>>>>> wlan0: [00:11:50:4d:c5:08] discard unhandled information element, id 47, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 46
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 40
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 43
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 12
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 40
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 12
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 45
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 13
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 13
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 13
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 47
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 12
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received beacon from 28:10:7b:8e:7a:ec rssi 44
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 51, len 8
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 127, len 1
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard unhandled information element, id 11, len 5
>>>>>> wlan0: [28:10:7b:8e:7a:ec] discard beacon frame, for off-channel 10
>>>>>> wlan0: received beacon from 74:44:01:2d:cb:5e rssi 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 47, len 1
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 74, len 14
>>>>>> wlan0: [74:44:01:2d:cb:5e] discard unhandled information element, id 127, len 1
>>>>>> wlan0: received probe_req from 00:aa:70:77:bd:77 rssi 0
>>>>>> wlan0: [00:aa:70:77:bd:77] recv probe req
>>>>>> wlan0: ieee80211_ref_node (ieee80211_send_proberesp:2489)
>>>>>> 0xc6f27000<00:15:6d:67:21:8d> refcnt 5
>>>>>> wlan0: send probe resp on channel 11 to 00:aa:70:77:bd:77
>>>>>> ath0: ath_raw_xmit: sc_inreset_cnt > 0; bailing
>>>>>> ....
>>>>>>
>>>>>>
>>>>>> On Tue, Jan 1, 2013 at 7:33 PM, Monthadar Al Jaberi <monthadar at gmail.com> wrote:
>>>>>>> Hi,
>>>>>>>
>>>>>>> ath(4) failed to attach on my Routerboard RB433AH running FreeBSD
>>>>>>> current. This is what I got during boo-up.
>>>>>>>
>>>>>>> pcib0 at irq 0 on nexus0
>>>>>>> pci0: <PCI bus> on pcib0
>>>>>>> ath0: <Atheros 5413> irq 3 at device 20.0 on pci0
>>>>>>> ath0: could not map interrupt
>>>>>>> device_attach: ath0 attach returned 6
>>>>>>>
>>>>>>> Any idea why? Anyone else is running ath(4) on this board? My wifi
>>>>>>> card is a Ubiquity X2 with AR5413 chip.
>>>>>>>
>>>>>>> br,
>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> Monthadar Al Jaberi
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Monthadar Al Jaberi
>>>>>> _______________________________________________
>>>>>> freebsd-wireless at freebsd.org mailing list
>>>>>> http://lists.freebsd.org/mailman/listinfo/freebsd-wireless
>>>>>> To unsubscribe, send any mail to "freebsd-wireless-unsubscribe at freebsd.org"
>>>>
>>>>
>>>>
>>>> --
>>>> Monthadar Al Jaberi
>>>
>>>
>>>
>>> --
>>> Monthadar Al Jaberi
>>
>>
>>
>> --
>> Monthadar Al Jaberi
--
Monthadar Al Jaberi
More information about the freebsd-mips
mailing list