Install problem HP integrity rx2660(Montecito)

[Richard Walter]

Hi Marcel,

i tried the August Snapshot of the 7.0 release, same problem.
I use the serial console for installation.

Best regards

Richard


error output:

FreeBSD/ia64 EFI boot, Revision 1.2
(root at pluto1.freebsd.org, Sat Aug 18 19:59:41 UTC 2007)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0xb36520+0x3f158 syms=[0x8+0x7a430+0x8+0x6ab34]
/
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Entering /boot/kernel/kernel at 0xe000000004070000...
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-CURRENT-200708 #0: Sun Aug 19 06:14:27 UTC 2007
     root at pluto1.freebsd.org:/usr/obj/usr/src/sys/GENERIC
CPU: Montecito (1594.71-Mhz Itanium 2)
   Origin = "GenuineIntel"  Revision = 7
   Features = 0x5<LB,AO>
real memory  = 8554143744 (8157 MB)
avail memory = 8095539200 (7720 MB)
FPSWA Revision = 0x10012, Entry = 0xe0000100ffd18050
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
cpu0: SAPIC Id=0, SAPIC Eid=0 (BSP)
cpu2: SAPIC Id=2, SAPIC Eid=0
acpi0: <HP> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> iomem 0xff5d8004-0xff5d8007 on acpi0
cpu0: <ACPI CPU> on acpi0
device_attach: acpi_perf0 attach returned 6
device_attach: acpi_perf0 attach returned 6
cpu1: <ACPI CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <unknown> at device 1.0 (no driver attached)
pci0: <simple comms> at device 1.1 (no driver attached)
uart0: <Non-standard ns8250 class UART with FIFOs> mem 0x88033000-0x88033fff irq 16 at 
device 1.2 on pci0
uart0: [FILTER]
uart0: console (9600,n,8,1)
ohci0: <NEC uPD 9210 USB controller> mem 0x88032000-0x88032fff irq 17 at device 2.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0
usb0: <NEC uPD 9210 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <NEC uPD 9210 USB controller> mem 0x88031000-0x88031fff irq 18 at device 2.1 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0
usb1: <NEC uPD 9210 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ehci0: <NEC uPD 720100 USB 2.0 controller> mem 0x88030000-0x880300ff irq 19 at device 2.2 
on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 3 ports each: usb0 usb1
usb2: <NEC uPD 720100 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 5 ports with 5 removable, self powered
umass0: <HEWLETT PACKARD INTEGRITY SERVER, class 0/0, rev 2.00/0.a1, addr 2> on uhub2
vgapci0: <VGA-compatible display> port 0x1000-0x10ff mem 
0x80000000-0x87ffffff,0x88020000-0x8802ffff at device 3.0 on pci0
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
mpt0: <LSILogic SAS/SATA Adapter> port 0x4000-0x40ff mem 
0xa0470000-0xa0473fff,0xa0460000-0xa046ffff irq 27 at device 1.0 on pci1
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.13.0
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
pci1:2:0: bad VPD cksum, remain 249
bge0: <PCI-X 2-port 2Gb FC/4port 1000BT COM MEZZ, ASIC rev. 0x2100> mem 
0xa0450000-0xa045ffff irq 29 at device 2.0 on pci1
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: Ethernet address: 00:17:a4:99:ad:bb
bge0: [ITHREAD]
pci1:2:1: bad VPD cksum, remain 249
bge1: <PCI-X 2-port 2Gb FC/4port 1000BT COM MEZZ, ASIC rev. 0x2100> mem 
0xa0440000-0xa044ffff irq 30 at device 2.1 on pci1
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: Ethernet address: 00:17:a4:99:ad:ba
bge1: [ITHREAD]
pcib2: <ACPI Host-PCI bridge> on acpi0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI Host-PCI bridge> on acpi0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI Host-PCI bridge> on acpi0
pci4: <ACPI PCI bus> on pcib4
uart1: <16550 or compatible> iomem 0xff5e2000-0xff5e2007 irq 24 on acpi0
uart1: [FILTER]
uart1: debug port (9600,n,8,1)
ukbd0: <HP Virtual Management Device, class 0/0, rev 1.10/0.01, addr 2> on uhub0
ums0: <HP Virtual Management Device, class 0/0, rev 1.10/0.01, addr 2> on uhub0
ums0: X report 0x0002 not supported
device_attach: ums0 attach returned 6
ukbd1: <CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 3> on uhub0
uhid0: <CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 3> on uhub0
Timecounters tick every 1.000 msec
md0: Preloaded image </boot/mfsroot> 8388608 bytes at 0xe000000004c5a5f0
SMP: 4 CPUs found; 2 CPUs usable; 2 CPUs woken
da0 at mpt0 bus 0 target 1 lun 0
da0: <HP DG146ABAB4 HPD5> Fixed Direct Access SCSI-5 device
da0: 300.000MB/s transfers
da0: Command Queueing Enabled
da0: 140014MB (286749488 512 byte sectors: 255H 63S/T 17849C)
cd0 at umass-sim0 bus 0 target 0 lun 0
cd0: <TEAC DV-28E-N C.6C> Removable CD-ROM SCSI-0 device
cd0: 40.000MB/s transfers
cd0: cd present [258620 x 2048 byte records]
GEOM_LABEL: Label for provider cd0 is iso9660/FreeBSD_Install.
GEOM_LABEL: Label for provider da0p1 is msdosfs/IA64_EFI.
Trying to mount root from ufs:/dev/md0




Marcel Moolenaar schrieb:
> 
> On Sep 4, 2007, at 5:07 AM, Richard Walter wrote:
> 
>> Hi Marcel,
>>
>> i've tried to install the August 07 Snapshot 6.2 Release.
>> The execution stops at the "Trying to mount root from ufs:/dev/md02"
>> line at the end of the following output.
> 
> None of the uart devices found claims to be the console. I assume you
> use the management board and 6.2 does not support that yet:
> 
>     pci0: <unknown> at device 1.0 (no driver attached)
>     pci0: <simple comms> at device 1.1 (no driver attached)
>     pci0: <simple comms, UART> at device 1.2 (no driver attached)
> 
> You need to use 7-CURRENT on Montecito hardware until I've
> ironed out all issues and merged the support to 6-STABLE.
> 
> FYI,
> 

____________
Virus checked by G DATA AntiVirusKit
Version: AVKA 17.403 from 05.09.2007
Virus news: www.antiviruslab.com