Install problem HP integrity rx2660(Montecito)

[Richard Walter]

Hello,

i have tried to install FreeBSD 7.0 from the April snapshot, now the console output hangs 
a little bit earlier.

Regards

Richard

Output from console:

FreeBSD/ia64 EFI boot, Revision 1.2
(root at pluto1.freebsd.org, Tue Apr 10 20:52:15 UTC 2007)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x9ff728 data=0x9b260+0x4cec8 syms=[0x8+0x7ad30+0x8+0x67ace]
/
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Entering /boot/kernel/kernel at 0xe000000004068000...
Skipping memory chunk start 0x100000000
Skipping memory chunk start 0x10040000000
Skipping memory chunk start 0x100ff000000
Skipping memory chunk start 0x100ff801000
Skipping memory chunk start 0x100ffa00000
Skipping memory chunk start 0x100ffe00000
Skipping memory chunk start 0x100ffe80000
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-CURRENT-200704 #0: Sat Apr 14 03:19:00 UTC 2007
     root at pluto1.freebsd.org:/usr/obj/usr/src/sys/GENERIC
CPU: Montecito (1594.71-Mhz Itanium 2)
   Origin = "GenuineIntel"  Revision = 7
   Features = 0x5<LB,AO>
real memory  = 1050492928 (1001 MB)
avail memory = 978149376 (932 MB)
FPSWA Revision = 0x10012, Entry = 0xe0000100ffd18050
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
cpu0: SAPIC Id=0, SAPIC Eid=0 (BSP)
cpu2: SAPIC Id=2, SAPIC Eid=0
acpi0: <HP> on motherboard



Marcel Moolenaar schrieb:
> On Apr 5, 2007, at 10:56 AM, Rick Jones wrote:
> 
>>> Unfortunately, we already have those IDs. What we don't have are the
>>> right sub-vendor and sub-device IDs :-(
>>
>> Details details... :)
>>
>>> Rick, could you run the lspci on Linux for me, provided you have the
>>> same management board?
>>
>> Sure, since the output is large, I'll send it to you directly rather 
>> than to the list, and let you summarize as you see fit.
> 
> The sub-device ID is 0x1301. Support for it has been added to
> FreeBSD -CURRENT (src/sys/dev/uart_bus_pci.c, rev 1.10). The
> April snapshot will have the fix. FreeBSD 6-STABLE will have
> the fix in a week, which is expected to show up starting the
> May snapshot.
> 
> Thank you Rick for the information!
> Thank you Richard for the report!
> 
> --Marcel Moolenaar
> xcllnt at mac.com
> 
> 

____________
Virus checked by G DATA AntiVirusKit
Version: AVK 17.4423 from 04.05.2007
Virus news: www.antiviruslab.com