i386/68900: 5.x install CDs fail to boot on Toshiba Satellite5205 s503 (4.10 dmesg)

[Alejandro Valenzuela]

The following reply was made to PR i386/68900; it has been noted by GNATS.

From: Alejandro Valenzuela <lanjoe9 at prodigy.net.mx>
To: freebsd-gnats-submit at FreeBSD.org, lanjoe9 at prodigy.net.mx
Cc:  
Subject: Re: i386/68900: 5.x install CDs fail to boot on Toshiba Satellite 5205
 s503 (4.10 dmesg)
Date: Sat, 10 Jul 2004 19:27:45 -0500

 4.10-RC2 dmesg of this machine (I wanted to send it with the PR but 
 couldn't, so here it goes)
 -----
 Copyright (c) 1992-2004 The FreeBSD Project.
 Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
 FreeBSD 4.10-RC2 #12: Sat Jul 10 16:37:05 CDT 2004
     lanjoe9 at citlalmina.earthshakers:/usr/src/sys/compile/CITLALMINA
 Timecounter "i8254"  frequency 1193182 Hz
 CPU: Intel(R) Pentium(R) 4 Mobile CPU 2.00GHz (1993.55-MHz 686-class CPU)
   Origin = "GenuineIntel"  Id = 0xf24  Stepping = 4
   
 Features=0x3febf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
 real memory  = 536657920 (524080K bytes)
 avail memory = 516071424 (503976K bytes)
 Preloaded elf kernel "kernel" at 0xc05ed000.
 Preloaded elf module "linux.ko" at 0xc05ed09c.
 Preloaded elf module "nvidia.ko" at 0xc05ed13c.
 Warning: Pentium 4 CPU: PSE disabled
 Pentium Pro MTRR support enabled
 md0: Malloc disk
 npx0: <math processor> on motherboard
 npx0: INT 16 interface
 pcib0: <Intel 82845 Host to PCI bridge> on motherboard
 pci0: <PCI bus> on pcib0
 agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xefffffff at 
 device 0.0 on pci0
 pcib1: <Intel 82845 PCI-PCI (AGP) bridge> at device 1.0 on pci0
 pci1: <PCI bus> on pcib1
 nvidia0: <GeForce4 460 Go> mem 
 0xd7f80000-0xd7ffffff,0xd8000000-0xdfffffff,0xfd000000-0xfdffffff irq 5 
 at device 0.0 on pci1
 pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
 pci2: <PCI bus> on pcib2
 ohci0: <NEC uPD 9210 USB controller> mem 0xfceff000-0xfcefffff irq 6 at 
 device 6.0 on pci2
 usb0: OHCI version 1.0
 usb0: SMM does not respond, resetting
 usb0: <NEC uPD 9210 USB controller> on ohci0
 usb0: USB revision 1.0
 uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub0: 3 ports with 3 removable, self powered
 ums0: Cypress Sem PS2/USB Browser Combo Mouse, rev 1.00/0.00, addr 2, 
 iclass 3/1ums0: 5 buttons and Z dir.
 ums1: Synaptics Inc. Synaptics WheelPad, rev 1.10/0.10, addr 3, iclass 3/1
 ums1: 3 buttons and Z dir.
 ohci1: <NEC uPD 9210 USB controller> mem 0xfcefe000-0xfcefefff irq 4 at 
 device 6.1 on pci2
 usb1: OHCI version 1.0
 usb1: SMM does not respond, resetting
 usb1: <NEC uPD 9210 USB controller> on ohci1
 usb1: USB revision 1.0
 uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub1: 2 ports with 2 removable, self powered
 pci2: <USB controller> at 6.2
 fwohci0: <Texas Instruments TSB43AB22/A> at device 7.0 on pci2
 fwohci0: Invalid irq 255
 fwohci0: Please switch PNP-OS to 'No' in BIOS
 fwohci0: Could not map memory
 device_probe_and_attach: fwohci0 attach returned 6
 fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0xdf40-0xdf7f mem 
 0xfcefd000-0xfcefdfff irq 4 at device 8.0 on pci2
 fxp0: Ethernet address 00:00:39:18:a5:dd
 inphy0: <i82562ET 10/100 media interface> on miibus0
 inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 pci2: <unknown card> (vendor=0x168c, dev=0x0013) at 10.0
 pcic0: chip is in D3 power mode -- setting to D0
 pci_cfgintr: can't route an interrupt to 2:11 INTA
 pcic0: <Toshiba ToPIC100 PCI-CardBus Bridge> at device 11.0 on pci2
 pcic0: PCI Memory allocated: 0x88000000
 pci_cfgintr: can't route an interrupt to 2:11 INTA
 pcic0: No PCI interrupt routed, trying ISA.
 pcic0: Polling mode
 pccard0: <PC Card 16-bit bus (classic)> on pcic0
 pci2: <unknown card> (vendor=0x1179, dev=0x0805) at 13.0
 isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0
 isa0: <ISA bus> on isab0
 atapci0: <Intel ICH3 ATA100 controller> port 
 0xcfa0-0xcfaf,0xcfe4-0xcfe7,0xcfe8-0xcfef,0xcff4-0xcff7,0xcff8-0xcfff 
 irq 11 at device 31.1 on pci0
 ata0: at 0x1f0 irq 14 on atapci0
 ata1: at 0x170 irq 15 on atapci0
 pci0: <unknown card> (vendor=0x8086, dev=0x2485) at 31.5
 pci0: <unknown card> (vendor=0x8086, dev=0x2486) at 31.6
 orm0: <Option ROMs> at iomem 0xc0000-0xcffff,0xe0000-0xeffff on isa0
 pmtimer0 on isa0
 fdc0: cannot reserve interrupt line
 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
 kbd0 at atkbd0
 psm0: <PS/2 Mouse> irq 12 on atkbdc0
 psm0: model IntelliMouse, device ID 3
 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
 sc0: <System console> at flags 0x100 on isa0
 sc0: VGA <16 virtual consoles, flags=0x300>
 sio0: configured irq 4 not in bitmap of probed irqs 0
 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
 sio0: type 8250
 sio1: configured irq 3 not in bitmap of probed irqs 0
 ppc0: parallel port not found.
 ad0: 38154MB <TOSHIBA MK4018GAS> [77520/16/63] at ata0-master UDMA100
 acd0: CD-RW <DW-224E> at ata0-slave PIO4
 Mounting root from ufs:/dev/ad0s4a
 cd0 at ata0 bus 0 target 1 lun 0
 cd0: <TEAC DW-224E 7.0A> Removable CD-ROM SCSI-0 device
 cd0: 16.000MB/s transfers
 cd0: Attempt to query device size failed: NOT READY, Medium not present
 ---- end of 4.10-RC2 dmesg---