Intel DP45SG motherboard problem (amd64)
John Baldwin
jhb at freebsd.org
Mon Mar 29 16:16:44 UTC 2010
On Saturday 27 March 2010 8:26:19 pm Alastair Hogge wrote:
> On Wed March 17 2010 23:23:03 John Baldwin wrote:
> > On Tuesday 16 March 2010 9:22:28 am Alastair Hogge wrote:
> > > On Tue March 2 2010 00:54:00 John Baldwin wrote:
> > > > This would not change acpidump output, just the kernel. Are you able
> > > > to capture the boot messages with this kernel?
> > >
> > > Full log:
> > > http://codepad.org/96PT5OO8
> >
> > Oh! ACPI is working, but the MADT is not so it's trying to mix and match
> > mptable (for SMP) with ACPI. Odd that you didn't get a warning message
> > about the checksum failing from boot -v. Try this patch:
> >
> > Index: amd64/acpica/acpi_machdep.c
> > ===================================================================
> > --- amd64/acpica/acpi_machdep.c (revision 205249)
> > +++ amd64/acpica/acpi_machdep.c (working copy)
> > @@ -627,8 +627,10 @@
> > if (ACPI_FAILURE(AcpiTbChecksum(table, length))) {
> > if (bootverbose)
> > printf("ACPI: Failed checksum for table %s\n", sig);
> > +#if (ACPI_CHECKSUM_ABORT)
> > table_unmap(table, length);
> > return (NULL);
> > +#endif
> > }
> > return (table);
> > }
> > Index: i386/acpica/acpi_machdep.c
> > ===================================================================
> > --- i386/acpica/acpi_machdep.c (revision 205249)
> > +++ i386/acpica/acpi_machdep.c (working copy)
> > @@ -641,8 +641,10 @@
> > if (ACPI_FAILURE(AcpiTbChecksum(table, length))) {
> > if (bootverbose)
> > printf("ACPI: Failed checksum for table %s\n", sig);
> > +#if (ACPI_CHECKSUM_ABORT)
> > table_unmap(table, length);
> > return (NULL);
> > +#endif
> > }
> > return (table);
> > }
> >
> OK, I've applied the patch to my i386 system & there doesn't appear to be
> problems so far.
>
> I also created an amd64 bootonly CD with the patch & was able to boot into
> sysinstall :-)
>
> [dcons connected]
> lapic: Divisor 2, Frequency 166664803 Hz
> ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 59
> Timecounter "TSC" frequency 2833301532 Hz quality -100
> Timecounters tick every 1.000 msec
> vlan: initialized, using hash tables with chaining
> lo0: bpf attached
> hptrr: no controller detected.
> ata2: Identifying devices: 00000001
> ata2: New devices: 00000001
> firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1) (me)
> firewire0: bus manager 1
> md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xffffffff8104f9f8
> usbus0: 12Mbps Full Speed USB v1.0
> usbus1: 12Mbps Full Speed USB v1.0
> usbus2: 12Mbps Full Speed USB v1.0
> usbus3: 480Mbps High Speed USB v2.0
> usbus4: 12Mbps Full Speed USB v1.0
> usbus5: 12Mbps Full Speed USB v1.0
> usbus6: 12Mbps Full Speed USB v1.0
> usbus7: 480Mbps High Speed USB v2.0
> ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
> ad4: setting UDMA100
> ad4: 286188MB <Maxtor 6V300F0 VA111630> at ata2-master UDMA100 SATA 3Gb/s
> ad4: 586114704 sectors [581463C/16H/63S] 16 sectors/interrupt 1 depth queue
> GEOM: new disk ad4
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> ugen2.1: <Intel> at usbus2
> uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
> ugen3.1: <Intel> at usbus3
> uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
> ugen4.1: <Intel> at usbus4
> uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
> ugen5.1: <Intel> at usbus5
> uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
> ugen6.1: <Intel> at usbus6
> uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
> ugen7.1: <Intel> at usbus7
> uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
> ad4: Intel check1 failed
> ad4: Adaptec check1 failed
> ad4: LSI (v3) check1 failed
> ad4: LSI (v2) check1 failed
> ad4: FreeBSD check1 failed
> ata3: Identifying devices: 00000001
> ata3: New devices: 00000001
> ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
> ad6: setting UDMA100
> ad6: 476940MB <SAMSUNG HD502HJ 1AJ100E4> at ata3-master UDMA100 SATA 3Gb/s
> ad6: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
> ad6: Intel check1 failed
> ad6: Adaptec check1 failed
> ad6: LSI (v3) check1 failed
> ad6: LSI (v2) check1 failed
> ad6: FreeBSD check1 failed
> ata4: Identifying devices: 00000001
> ata4: New devices: 00000001
> ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
> ad8: setting UDMA100
> ad8: 114473MB <Seagate ST3120026AS 3.05> at ata4-master UDMA100 SATA 1.5Gb/s
> ad8: 234441648 sectors [232581C/16H/63S] 16 sectors/interrupt 1 depth queue
> ad8: Intel check1 failed
> ad8: Adaptec check1 failed
> ad8: LSI (v3) check1 failed
> ad8: LSI (v2) check1 failed
> ad8: FreeBSD check1 failed
> ata5: Identifying devices: 00000000
> ata5: New devices: 00000000
> ata6: Identifying devices: 00000001
> ata6: New devices: 00000001
> ata6-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
> ad12: setting UDMA100
> ad12: 476940MB <SAMSUNG HD502HJ 1AJ100E4> at ata6-master UDMA100 SATA 3Gb/s
> ad12: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
> ad12: Intel check1 failed
> ad12: Adaptec check1 failed
> ad12: LSI (v3) check1 failed
> ad12: LSI (v2) check1 failed
> ad12: FreeBSD check1 failed
> ata7: Identifying devices: 00010000
> ata7: New devices: 00010000
> ata7-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
> acd0: setting UDMA100
> ata7: device_reset timeout=230us
> acd0: <ASUS DRW-20B1LT/1.00> DVDR drive at ata7 as master
> acd0: read 8269KB/s (8269KB/s) write 8269KB/s (8269KB/s), 2048KB buffer,
> UDMA100 SATA 1.5Gb/s
> acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
> acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
> acd0: Audio: play, 256 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: CD-ROM 120mm data disc
> GEOM: new disk ad6
> GEOM: new disk ad8
> GEOM: new disk ad12
> firewire0: New S400 device ID:00902700022b34b9
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> uhub2: 2 ports with 2 removable, self powered
> uhub4: 2 ports with 2 removable, self powered
> uhub5: 2 ports with 2 removable, self powered
> uhub6: 2 ports with 2 removable, self powered
> uhub3: 6 ports with 6 removable, self powered
> uhub7: 6 ports with 6 removable, self powered
> ugen0.2: <ALCOR> at usbus0
> uhub8: <ALCOR Generic USB Hub, class 9/0, rev 1.10/3.12, addr 2> on usbus0
> (probe1:sbp0:0:1:0): Error 22, Unretryable error
> (probe2:sbp0:0:2:0): Error 22, Unretryable error
> (probe3:sbp0:0:3:0): Error 22, Unretryable error
> (probe0:sbp0:0:0:0): Error 22, Unretryable error
> (probe4:sbp0:0:4:0): Error 22, Unretryable error
> (probe5:sbp0:0:5:0): Error 22, Unretryable error
> (probe6:sbp0:0:6:0): Error 22, Unretryable error
> ATA PseudoRAID loaded
> SMP: AP CPU #1 Launched!
> cpu1 AP:
> ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
> timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
> SMP: AP CPU #3 Launched!
> cpu3 AP:
> ID: 0x03000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
> timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
> SMP: AP CPU #2 Launched!
> cpu2 AP:
> ID: 0x02000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
> timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
> ioapic0: routing intpin 3 (ISA fIlRoQw t3a)b lteo cllaepaince r1
> svteacrttoerd 4
> 8
> ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 2 vector 48
> ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 3 vector 48
> ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 1 vector 49
> ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 2 vector 49
> ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 3 vector 49
> ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 1 vector 50
> ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 2 vector 50
> msi: Assigning MSI IRQ 256 to local APIC 3 vector 50
> WARNING: WITNESS option enabled, expect reduced performance.
> ugen1.2: <DATACOMP> at usbus1
> ukbd0: <DATACOMP SteelSDATA, class 0/0, rev 1.10/0.01, addr 2> on usbus1
> kbd2 at ukbd0
> kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
> ums0: <DATACOMP SteelSDATA, class 0/0, rev 1.10/0.01, addr 2> on usbus1
> uhub8: 4 ports with 4 removable, self powered
> ugen0.3: <SteelSeries ApS> at usbus0
> ums1: <SteelSeries ApS Ikari Laser, class 0/0, rev 2.00/1.00, addr 3> on
> usbus0
> ums1: 7 buttons and [XYZ] coordinates ID=2
> acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x05
> acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x05
> Trying to mount root from ufs:/dev/md0
> ct_to_ts([2010-03-28 08:05:57]) = 1269763557.000000000
> start_init: trying /sbin/init
> start_init: trying /sbin/oinit
> start_init: trying /sbin/init.bak
> start_init: trying /rescue/init
> start_init: trying /stand/sysinstall
>
> Thanks for the help John & *, any chance this will get committed?
It is already in the tree and merged to 7 and 8. It should be present in 7.4
and 8.1.
--
John Baldwin
More information about the freebsd-hardware
mailing list