SUN X2100 M2 with FreeBSD 7.0 BETA-4
MeX
mex at active.sk
Tue Dec 11 15:01:32 PST 2007
Hello all,
just for information I'm posting a dmesg, ubench and diskinfo output
from recent SUN X2100 M2 machine with AMD Opteron 1222, 4GB RAM and 2x
73GB SAS Seagate HDD in RAID1 on LSI Logic LSI3041E SAS HBA PCIe
internal card bus. Test was done with FreeBSD 7.0-BETA4 (amd64) with
GENERIC kernel.
Regards,
MeX
-------------- next part --------------
sundb# uname -a
FreeBSD xxx.zzz.yyy 7.0-BETA4 FreeBSD 7.0-BETA4 #0: Sun Dec 2 16:34:41 UTC 2007 root at myers.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
sundb# diskinfo -v -t da0
da0
512 # sectorsize
72999763968 # mediasize in bytes (68G)
142577664 # mediasize in sectors
8875 # Cylinders according to firmware.
255 # Heads according to firmware.
63 # Sectors according to firmware.
Seek times:
Full stroke: 250 iter in 0.711167 sec = 2.845 msec
Half stroke: 250 iter in 0.726595 sec = 2.906 msec
Quarter stroke: 500 iter in 1.243543 sec = 2.487 msec
Short forward: 400 iter in 1.129032 sec = 2.823 msec
Short backward: 400 iter in 0.779911 sec = 1.950 msec
Seq outer: 2048 iter in 0.251691 sec = 0.123 msec
Seq inner: 2048 iter in 0.249642 sec = 0.122 msec
Transfer rates:
outside: 102400 kbytes in 0.798880 sec = 128179 kbytes/sec
middle: 102400 kbytes in 0.906083 sec = 113014 kbytes/sec
inside: 102400 kbytes in 1.348922 sec = 75912 kbytes/sec
-------------- next part --------------
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-BETA4 #0: Sun Dec 2 16:34:41 UTC 2007
root at myers.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Dual-Core AMD Opteron(tm) Processor 1222 (3015.47-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0x40f33 Stepping = 3
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x2001<SSE3,CX16>
AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8>
Cores per package: 2
usable memory = 4282429440 (4084 MB)
avail memory = 4128944128 (3937 MB)
ACPI APIC Table: <A M I OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0 <Version 1.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <A M I OEMXSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, dff00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x2008-0x200b on acpi0
cpu0: <ACPI CPU> on acpi0
powernow0: <PowerNow! K8> on cpu0
cpu1: <ACPI CPU> on acpi0
powernow1: <PowerNow! K8> on cpu1
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xfcffb000-0xfcffbfff irq 21 at device 2.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 8 ports with 8 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfcffac00-0xfcffacff irq 22 at device 2.1 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb1: EHCI version 1.0
usb1: companion controller, 10 ports each: usb0
usb1: <EHCI (generic) USB 2.0 controller> on ehci0
usb1: USB revision 2.0
uhub1: <nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb1
uhub1: 8 ports with 8 removable, self powered
atapci0: <nVidia nForce MCP55 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 4.0 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
atapci1: <nVidia nForce MCP55 SATA300 controller> port 0xc480-0xc487,0xc400-0xc403,0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc0f mem 0xfcff9000-0xfcff9fff irq 23 at device 5.0 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xdc00-0xdc7f mem 0xfd000000-0xfd7fffff,0xfdbe0000-0xfdbfffff irq 16 at device 5.0 on pci1
nfe0: <NVIDIA nForce MCP55 Networking Adapter> port 0xb880-0xb887 mem 0xfcff8000-0xfcff8fff,0xfcffa800-0xfcffa8ff,0xfcffa400-0xfcffa40f irq 20 at device 8.0 on pci0
miibus0: <MII bus> on nfe0
e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 2 on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
nfe0: Ethernet address: 00:1b:24:93:a4:62
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe1: <NVIDIA nForce MCP55 Networking Adapter> port 0xb800-0xb807 mem 0xfcff7000-0xfcff7fff,0xfcffa000-0xfcffa0ff,0xfcff6c00-0xfcff6c0f irq 21 at device 9.0 on pci0
miibus1: <MII bus> on nfe1
e1000phy1: <Marvell 88E1149 Gigabit PHY> PHY 3 on miibus1
e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
nfe1: Ethernet address: 00:1b:24:93:a4:63
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
mpt0: <LSILogic SAS/SATA Adapter> port 0xe000-0xe0ff mem 0xfdefc000-0xfdefffff,0xfdee0000-0xfdeeffff irq 17 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.12.0
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 12.0 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 13.0 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> at device 0.0 on pci5
pci6: <ACPI PCI bus> on pcib6
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x9003> mem 0xfdff0000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 18 at device 4.0 on pci6
miibus2: <MII bus> on bge0
brgphy0: <BCM5714 10/100/1000baseTX PHY> PHY 1 on miibus2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: Ethernet address: 00:1b:24:93:a4:60
bge0: [ITHREAD]
bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x9003> mem 0xfdfc0000-0xfdfcffff,0xfdfb0000-0xfdfbffff irq 19 at device 4.1 on pci6
miibus3: <MII bus> on bge1
brgphy1: <BCM5714 10/100/1000baseTX PHY> PHY 1 on miibus3
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: Ethernet address: 00:1b:24:93:a4:61
bge1: [ITHREAD]
pcib7: <ACPI PCI-PCI bridge> at device 14.0 on pci0
pci7: <ACPI PCI bus> on pcib7
pcib8: <ACPI PCI-PCI bridge> at device 15.0 on pci0
pci8: <ACPI PCI bus> on pcib8
acpi_button0: <Power Button> on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio1: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xd0800-0xd1fff,0xd2000-0xd2fff on isa0
ppc0: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ukbd0: <Virtual USB MULTIMEDIA KEYBOARD, class 0/0, rev 1.10/0.01, addr 2> on uhub0
kbd2 at ukbd0
ums0: <Virtual USB MULTIMEDIA KEYBOARD, class 0/0, rev 1.10/0.01, addr 2> on uhub0
ums0: 3 buttons and Z dir.
uhub2: <vendor 0x0451 product 0x1446, class 9/0, rev 1.10/1.10, addr 3> on uhub0
uhub2: 4 ports with 4 removable, self powered
ukbd1: <vendor 0x045e Microsoft Internet Keyboard Pro, class 0/0, rev 1.10/1.14, addr 4> on uhub2
kbd3 at ukbd1
uhid0: <vendor 0x045e Microsoft Internet Keyboard Pro, class 0/0, rev 1.10/1.14, addr 4> on uhub2
Timecounters tick every 1.000 msec
acd0: DMA limited to UDMA33, device found non-ATA66 cable
acd0: DVDROM <MATSHITADVD-ROM SR-8178/PZ16> at ata0-master UDMA33
da0 at mpt0 bus 0 target 0 lun 0
da0: <LSILOGIC Logical Volume 3000> Fixed Direct Access SCSI-2 device
da0: 300.000MB/s transfers
da0: Command Queueing Enabled
da0: 69618MB (142577664 512 byte sectors: 255H 63S/T 8875C)
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/da0s1a
Loading configuration files.
kernel dumps on /dev/da0s1b
Entropy harvesting:
interrupts
ethernet
point_to_point
kickstart
.
swapon: adding /dev/da0s1b as swap device
Starting file system checks:
/dev/da0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1a: clean, 153419 free (2427 frags, 18874 blocks, 1.0% fragmentation)
/dev/da0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1e: clean, 253813 free (21 frags, 31724 blocks, 0.0% fragmentation)
/dev/da0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1f: clean, 29056841 free (18481 frags, 3629795 blocks, 0.1% fragmentation)
/dev/da0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1d: clean, 2530250 free (146 frags, 316263 blocks, 0.0% fragmentation)
Setting hostuuid: b8a8fb50-ed79-0010-b897-001b2493a6d9.
Setting hostid: 0xb5d565d3.
Mounting local file systems:
.
Setting hostname: xxx.zzz.yyy.
net.inet6.ip6.auto_linklocal:
1
->
0
bge0: no link ...
.
got link
DHCPREQUEST on bge0 to 255.255.255.255 port 67
DHCPACK from 192.168.2.1
bound to 192.168.2.119 -- renewal in 3600 seconds.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
ether 00:1b:24:93:a4:60
inet 192.168.2.119 netmask 0xffffff00 broadcast 192.168.2.255
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
Additional routing options:
.
Starting devd.
Configuring keyboard:
.
Starting ums0 moused:
.
hw.acpi.cpu.cx_lowest:
C1
->
C1
Generating host.conf.
Additional IP options:
.
Mounting NFS file systems:
.
Creating and/or trimming log files:
.
Starting syslogd.
Checking for core dump on /dev/da0s1b...
savecore: no dumps found
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
32-bit compatibility ldconfig path: /usr/lib32
ldconfig:
warning: /usr/lib32
:
No such file or directory
Initial amd64 initialization:
.
Additional ABI support:
.
Clearing /tmp (X related).
Starting local daemons:
.
Updating motd
.
Mounting late file systems:
.
Configuring syscons:
blanktime
.
Generating public/private rsa1 key pair.
Your identification has been saved in /etc/ssh/ssh_host_key.
Your public key has been saved in /etc/ssh/ssh_host_key.pub.
The key fingerprint is:
74:ac:e7:51:58:08:51:1a:50:cf:d0:e3:d3:a9:22:15 root at xxx.yyy.zzz
Generating public/private dsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_dsa_key.
Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub.
The key fingerprint is:
10:a0:81:99:b1:9f:94:db:34:80:d7:e9:d5:bd:4c:31 root at xxx.yyy.zzz
Generating public/private rsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_rsa_key.
Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub.
The key fingerprint is:
3c:79:d0:4a:29:d5:f8:46:78:8a:d7:da:33:0f:c0:9c root at xxx.yyy.zzz
Starting sshd.
Starting cron.
Local package initialization:
.
Starting background file system checks in 60 seconds.
Tue Dec 11 18:11:45 CET 2007
Dec 11 18:13:36 sundb login: ROOT LOGIN (root) ON ttyv0
-------------- next part --------------
sundb# ubench
Unix Benchmark Utility v.0.3
Copyright (C) July, 1999 PhysTech, Inc.
Author: Sergei Viznyuk <sv at phystech.com>
http://www.phystech.com/download/ubench.html
FreeBSD 7.0-BETA4 FreeBSD 7.0-BETA4 #0: Sun Dec 2 16:34:41 UTC 2007 root at myers.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
Ubench CPU: 320435
Ubench MEM: 173616
--------------------
Ubench AVG: 247025
sundb#
More information about the freebsd-hardware
mailing list