isp/ispfw

[Tony Maher]

Hello

I am trying to get a Qlogic 2300 to talk to a SAN under 5.1-Release.
I have never played with fiber before so I am not sure of what I am supposed
to be doing.

The device is recognized ok.

ahc0: Features 0x1def6, Bugs 0x40, Flags 0x20485540
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Qlogic ISP Driver, FreeBSD Version 5.9, Core Version 2.7
isp0: <Qlogic ISP 2300 PCI FC-AL Adapter> port 0x2400-0x24ff mem 0xefffe000-0xef
ffefff irq 11 at device 5.0 on pci1
isp0: using I/O space register mapping
isp0: Board Type 2300, Chip Revision 0x1, loaded F/W Revision 3.1.20
isp0: Installed in 64-Bit PCI slot
isp0: 744 max I/O commands supported
isp0: NVRAM Port WWN 0x210000e08b05c18e
unknown: not probed (disabled)
unknown: not probed (disabled)
...
...
isp0: LIP Received
isp0: Loop UP
isp0: Port Database Changed
isp0: Firmware State <Config Wait->Ready>
isp0: 2Gb link speed/s
isp0: Loop ID 1, AL_PA 0xe8, Port ID 0xe8, Loop State 0x2, Topology 'Private Loo
p'
isp0: Target 1 (Loop 0x1) Port ID 0xe8 (role Target/Initiator) Arrived
 Port WWN 0x210000e08b05c18e  
 Node WWN 0x200000e08b05c18e  
isp0: Target 0 (Loop 0x0) Port ID 0xef (role Target) Arrived
 Port WWN 0x50060e80008273d2
 Node WWN 0x50060e80008273d2
ata0-master: piomode=12 dmamode=34 udmamode=66 dmaflag=1
ata0-master: success setting PIO4 on ServerWorks ROSB4 chip
acd0: <LG CD-ROM CRN-8245B/1.13> CDROM drive at ata0 as master
...
...
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
isp0: port unavailable for target 1
isp0: Firmware State <Config Wait->Waiting for AL_PA>
(probe19:isp0:0:4:0): Request Requeued
(probe19:isp0:0:4:0): Retrying Command
isp0: LIP Received
isp0: Firmware State <Waiting for AL_PA->Wait Login>
isp0: Port Database Changed
isp0: Firmware State <Wait Login->Ready>
isp0: 2Gb link speed/s
isp0: Loop ID 1, AL_PA 0xe8, Port ID 0xe8, Loop State 0x2, Topology 'Private Loo
p'
isp0: Target 1 (Loop 0x1) Port ID 0xe8 (role Target/Initiator) Arrived
 Port WWN 0x210000e08b05c18e  
 Node WWN 0x200000e08b05c18e  
isp0: Retaining Loop ID 0x0 for Target 0 (Port 0xef)
(probe0:ahc0:0:0:0): Retrying Command
(ahc0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
...
...
start_init: trying /sbin/init
Linux ELF exec handler installed
isp0: port unavailable for target 1
isp0: Mbox Command Async (0x4000) with no waiters
isp0: Firmware State <Config Wait->Waiting for AL_PA>
isp0: LIP Received
isp0: Firmware State <Waiting for AL_PA->Wait Login>
isp0: Port Database Changed
isp0: Firmware State <Wait Login->Ready>
isp0: 2Gb link speed/s
isp0: Loop ID 1, AL_PA 0xe8, Port ID 0xe8, Loop State 0x2, Topology 'Private Loop'
isp0: Target 1 (Loop 0x1) Port ID 0xe8 (role Target/Initiator) Arrived
 Port WWN 0x210000e08b05c18e
  Node WWN 0x200000e08b05c18e
isp0: Retaining Loop ID 0x0 for Target 0 (Port 0xef)


The kernel config is basically GENERIC  but has
device      isp     # Qlogic family
device      ispfw
options     ISP_TARGET_MODE=1


'camcontrol devlist -v' reports
scbus0 on ahc0 bus 0:
<IBM-PSG DDYS-T18350M  M S9HA>     at scbus0 target 0 lun 0 (pass0,da0)
<IBM FTlV1 S2 0>                   at scbus0 target 8 lun 0 (ses0,pass1)
<  >                               at scbus0 target -1 lun -1 ()
scbus1 on isp0 bus 0:
<  >                               at scbus1 target -1 lun -1 ()
scbus-1 on xpt0 bus 0:
<  >                               at scbus-1 target -1 lun -1 (xpt0)


Using the card bios util, it reports along the lines of:

                 WNN               Port
0 Hitachi DF600F 50060E8000827302  0000EF
1 Qlogic  2300   210000E08B05C18E  0000E8


I have booted without defining ISP_TARGET_MODE=1 but the camcntrol devlist -v
reports the same. 
Any ideas on what is wrong (I know nothing about the SAN itself, someone
else set it up). 

thanks
--
tonym