netspeed not allowing selection of device
Sean McNeil
sean at mcneil.com
Mon Oct 2 15:24:10 PDT 2006
Hi folks,
Running gnome-2.14 on my amd64 -STABLE box I was able to select the
network device that it reports information about until recently. I just
put in a wireless NIC and setup the box to bridge my internal network
with the 802.11g. This added an ath0 device plus bridge0. I now have:
ath0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 2290
inet6 xxx%ath0 prefixlen 64 scopeid 0x1
inet6 xxx prefixlen 64
inet6 xxx prefixlen 64 anycast
ether 00:11:95:c4:3c:aa
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
status: associated
ssid McNeil channel 9 bssid 00:11:95:c4:3c:aa
authmode WPA privacy MIXED deftxkey 3 TKIP 2:128-bit TKIP 3:128-bit
txpowmax 36 bmiss 7 protmode CTS burst dtimperiod 1 bintval 100
fwe0: flags=108943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST,NEEDSGIANT> mtu 1500
options=8<VLAN_MTU>
inet6 xxx%fwe0 prefixlen 64 scopeid 0x2
ether 02:11:06:00:75:68
ch 1 dma 0
dc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 xxx%dc0 prefixlen 64 scopeid 0x3
inet xxx.xxx.xxx.xxx netmask 0xfffffffc broadcast xxx.xxx.xxx.xxx
inet 192.168.1.254 netmask 0xffffff00 broadcast 192.168.1.255
inet6 xxx prefixlen 64
inet6 xxx prefixlen 64 anycast
ether 00:03:6d:1a:b1:9b
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
sk0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 xxx prefixlen 64 anycast
inet6 xxx%sk0 prefixlen 64 scopeid 0x4
inet6 xxx prefixlen 64
ether 00:14:85:85:27:b3
media: Ethernet autoselect (1000baseTX <full-duplex,flag0,flag1>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
inet 127.0.0.1 netmask 0xff000000
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 10.0.0.1 netmask 0xff000000 broadcast 10.255.255.255
ether e6:72:7c:ad:4c:26
priority 32768 hellotime 2 fwddelay 15 maxage 20
member: ath0 flags=3<LEARNING,DISCOVER>
member: sk0 flags=3<LEARNING,DISCOVER>
stf0: flags=1<UP> mtu 1280
inet6 2002:18c7:2d36::1 prefixlen 16
The net monitor applet will show all the devices and shows an error if I
select ath0 or sk0, but netspeed has the device selection disabled and
only shows ath0.
More information about the freebsd-gnome
mailing list