sanity check: is 9211-8i, on 8.3, with IT firmware still "the
one"
Dennis Glatting
dg at pki2.com
Fri Jan 20 16:31:57 UTC 2012
On Fri, 2012-01-20 at 07:31 -0800, Jeremy Chadwick wrote:
> On Fri, Jan 20, 2012 at 06:22:11AM -0800, Dennis Glatting wrote:
> > I am having a problem with Seagate ST1000DL002 disks but I haven't yet
> > determined weather it is the disks themselves (they -- two of them, new
> > -- fail under a MB controller too.
>
> Assuming the disks are seen directly on the bus (e.g. show up as daX,
> adaX, or whatever), please install ports/sysutils/smartmontools (make
> sure you're using version 5.42 or newer) and please provide output from
> the following command: "smartctl -a /dev/XXX" where XXX is the device
> name of the ST1000DL002 disk(s). Please be sure to state which device
> name is associated with which smartctl output. You can delete or
> remove the disk serial numbers from the output (for privacy) if you
> wish. I'll be happy to review the data and tell you whether or not the
> disks themselves are showing problems or if the issue is elsewhere.
>
That is the motivation I needed to reboot that system, which was 50%
through a task. That said, as remains the case today, for the last 20
years I haven't been able to find that "Any Key" on reboot. :)
Regardless...
The problematic disk from dmesg:
da12 at mps2 bus 0 scbus4 target 5 lun 0
da12: <ATA ST1000DL002-9TT1 CC32> Fixed Direct Access SCSI-6 device
da12: 300.000MB/s transfers
da12: Command Queueing enabled
da12: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C)
An attempt to write to it:
bd3# dd if=/dev/zero of=/dev/da12
dd: /dev/da12: Input/output error
1+0 records in
0+0 records out
0 bytes transferred in 0.378153 secs (0 bytes/sec)
The disk is presently connected to this device (LSI 9211-8i) but I have
also had it connected to the devices on the MB and I think to a
SuperMicro board. I have also tried a different LSI board.
bd3# dmesg | grep mps2
mps2: <LSI SAS2008> port 0x8e00-0x8eff mem
0xfdcfc000-0xfdcfffff,0xfdc80000-0xfdcbffff irq 16 at device 0.0 on pci6
mps2: Firmware: 12.00.00.00
mps2: IOCCapabilities:
1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
The system is:
bd3# uname -a
FreeBSD bd3 9.0-STABLE FreeBSD 9.0-STABLE #1: Tue Jan 10 22:34:53 PST
2012 root at bd3:/sys/amd64/compile/BULLDOZER amd64
Full dmesg at the end. Note the errors with da12.
And your request:
bd3# smartctl -a /dev/da12
smartctl 5.42 2011-10-20 r3458 [FreeBSD 9.0-STABLE amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen,
http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda Green (Adv. Format)
Device Model: ST1000DL002-9TT153
Serial Number: W1V06SLR
LU WWN Device Id: 5 000c50 037e11be9
Firmware Version: CC32
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Fri Jan 20 08:22:34 2012 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 612) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 169) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x30b7) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 108 099 006 Pre-fail Always
- 241488
3 Spin_Up_Time 0x0003 087 070 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
- 28
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always
- 136324
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 576
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 29
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always
- 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 073 062 045 Old_age Always
- 27 (Min/Max 21/27)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 23
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always
- 29
194 Temperature_Celsius 0x0022 027 040 000 Old_age Always
- 27 (0 21 0 0 0)
195 Hardware_ECC_Recovered 0x001a 027 008 000 Old_age Always
- 241488
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age
Offline - 265544943010369
241 Total_LBAs_Written 0x0000 100 253 000 Old_age
Offline - 3746932548
242 Total_LBAs_Read 0x0000 100 253 000 Old_age
Offline - 3212957483
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 309
-
# 2 Short offline Completed without error 00% 285
-
# 3 Short offline Completed without error 00% 261
-
# 4 Extended offline Completed without error 00% 258
-
# 5 Short offline Completed without error 00% 237
-
# 6 Short offline Completed without error 00% 213
-
# 7 Short offline Completed without error 00% 189
-
# 8 Short offline Completed without error 00% 175
-
# 9 Short offline Completed without error 00% 151
-
#10 Short offline Completed without error 00% 127
-
#11 Short offline Completed without error 00% 103
-
#12 Short offline Completed without error 00% 79
-
#13 Short offline Completed without error 00% 55
-
#14 Short offline Completed without error 00% 31
-
#15 Short offline Completed without error 00% 7
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
bd3# dmesg
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-STABLE #1: Tue Jan 10 22:34:53 PST 2012
root at bd3:/sys/amd64/compile/BULLDOZER amd64
CPU: AMD FX(tm)-8150 Eight-Core Processor (4017.98-MHz
K8-class CPU)
Origin = "AuthenticAMD" Id = 0x600f12 Family = 15 Model = 1
Stepping = 2
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x1698220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,AVX>
AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
AMD
Features2=0x1c9bfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,NodeId,Topology,<b23>,<b24>>
TSC: P-state invariant, performance statistics
real memory = 17179869184 (16384 MB)
avail memory = 16507908096 (15743 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <GBT GBTUACPI>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 8 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
cpu6 (AP): APIC ID: 6
cpu7 (AP): APIC ID: 7
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <GBT GBTUACPI> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cfca0000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.2 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 19 at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib1
mps0: <LSI SAS2008> port 0xde00-0xdeff mem
0xfd9fc000-0xfd9fffff,0xfd980000-0xfd9bffff irq 19 at device 0.0 on pci1
mps0: Firmware: 12.00.00.00
mps0: IOCCapabilities:
1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
pci2: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xcf00-0xcf1f mem
0xfd7c0000-0xfd7dffff,0xfd700000-0xfd77ffff,0xfd7fc000-0xfd7fffff irq 16
at device 0.0 on pci2
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:1b:21:c6:d2:a0
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 9.0 on pci0
pci3: <ACPI PCI bus> on pcib3
xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfd5f8000-0xfd5fffff irq
17 at device 0.0 on pci3
xhci0: 64 byte context size.
usbus0 on xhci0
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
pci4: <ACPI PCI bus> on pcib4
atapci0: <Marvell ATA controller> port
0xaf00-0xaf07,0xae00-0xae03,0xad00-0xad07,0xac00-0xac03,0xab00-0xab0f
mem 0xfcbff000-0xfcbff1ff irq 18 at device 0.0 on pci4
ata2: <ATA channel> at channel 0 on atapci0
ata3: <ATA channel> at channel 1 on atapci0
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 11.0 on pci0
pci5: <ACPI PCI bus> on pcib5
mps1: <LSI SAS2008> port 0x9e00-0x9eff mem
0xfdefc000-0xfdefffff,0xfde80000-0xfdebffff irq 19 at device 0.0 on pci5
mps1: Firmware: 12.00.00.00
mps1: IOCCapabilities:
185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 12.0 on pci0
pci6: <ACPI PCI bus> on pcib6
mps2: <LSI SAS2008> port 0x8e00-0x8eff mem
0xfdcfc000-0xfdcfffff,0xfdc80000-0xfdcbffff irq 16 at device 0.0 on pci6
mps2: Firmware: 12.00.00.00
mps2: IOCCapabilities:
1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
pcib7: <ACPI PCI-PCI bridge> irq 17 at device 13.0 on pci0
pci7: <ACPI PCI bus> on pcib7
vgapci0: <VGA-compatible display> port 0xee00-0xeeff mem
0xd0000000-0xdfffffff,0xfdac0000-0xfdadffff irq 17 at device 0.0 on pci7
hdac0: <ATI (Unknown) High Definition Audio Controller> mem
0xfdafc000-0xfdafffff irq 18 at device 0.1 on pci7
ahci0: <ATI IXP700 AHCI SATA controller> port
0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f
mem 0xfdfff000-0xfdfff3ff irq 19 at device 17.0 on pci0
ahci0: AHCI v1.20 with 4 6Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ohci0: <OHCI (generic) USB controller> mem 0xfdffe000-0xfdffefff irq 18
at device 18.0 on pci0
usbus1: <OHCI (generic) USB controller> on ohci0
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfdffd000-0xfdffd0ff irq
17 at device 18.2 on pci0
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci1: <OHCI (generic) USB controller> mem 0xfdffc000-0xfdffcfff irq 18
at device 19.0 on pci0
usbus3: <OHCI (generic) USB controller> on ohci1
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfdffb000-0xfdffb0ff irq
17 at device 19.2 on pci0
usbus4: EHCI version 1.0
usbus4: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700/800 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 20.1 on pci0
ata0: <ATA channel> at channel 0 on atapci1
ata1: <ATA channel> at channel 1 on atapci1
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib8: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci8: <ACPI PCI bus> on pcib8
ohci2: <OHCI (generic) USB controller> mem 0xfdffa000-0xfdffafff irq 18
at device 20.5 on pci0
usbus5: <OHCI (generic) USB controller> on ohci2
pcib9: <ACPI PCI-PCI bridge> at device 21.0 on pci0
pci9: <ACPI PCI bus> on pcib9
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port
0x6e00-0x6eff mem 0xfd0ff000-0xfd0fffff,0xfd0f8000-0xfd0fbfff irq 17 at
device 0.0 on pci9
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on
miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 50:e5:49:45:55:8e
pcib10: <ACPI PCI-PCI bridge> at device 21.1 on pci0
pci10: <ACPI PCI bus> on pcib10
xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfcff8000-0xfcffffff irq
17 at device 0.0 on pci10
xhci1: 64 byte context size.
usbus6 on xhci1
pcib11: <ACPI PCI-PCI bridge> at device 21.2 on pci0
pci11: <ACPI PCI bus> on pcib11
atapci2: <Marvell ATA controller> port
0x3f00-0x3f07,0x3e00-0x3e03,0x3d00-0x3d07,0x3c00-0x3c03,0x3b00-0x3b0f
mem 0xfcdff000-0xfcdff1ff irq 17 at device 0.0 on pci11
ata4: <ATA channel> at channel 0 on atapci2
ata5: <ATA channel> at channel 1 on atapci2
ohci3: <OHCI (generic) USB controller> mem 0xfdff9000-0xfdff9fff irq 18
at device 22.0 on pci0
usbus7: <OHCI (generic) USB controller> on ohci3
ehci2: <EHCI (generic) USB 2.0 controller> mem 0xfdff8000-0xfdff80ff irq
17 at device 22.2 on pci0
usbus8: EHCI version 1.0
usbus8: <EHCI (generic) USB 2.0 controller> on ehci2
attimer0: <AT timer> port 0x40-0x43 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8
on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcffff,0xd0000-0xd5fff,0xd6000-0xd6fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounters tick every 1.000 msec
hdac0: HDA Codec #0: ATI R6xx HDMI
pcm0: <HDA ATI R6xx HDMI PCM #0 HDMI> at cad 0 nid 1 on hdac0
usbus0: 5.0Gbps Super Speed USB v3.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 5.0Gbps Super Speed USB v3.0
usbus7: 12Mbps Full Speed USB v1.0
usbus8: 480Mbps High Speed USB v2.0
ugen0.1: <0x1b6f> at usbus0
uhub0: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <0x1b6f> at usbus6
uhub6: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
usbus6
ugen7.1: <ATI> at usbus7
uhub7: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus7
ugen8.1: <ATI> at usbus8
uhub8: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus8
uhub5: 2 ports with 2 removable, self powered
uhub7: 4 ports with 4 removable, self powered
uhub1: 5 ports with 5 removable, self powered
uhub3: 5 ports with 5 removable, self powered
uhub0: 4 ports with 4 removable, self powered
uhub6: 4 ports with 4 removable, self powered
uhub8: 4 ports with 4 removable, self powered
uhub2: 5 ports with 5 removable, self powered
uhub4: 5 ports with 5 removable, self powered
ugen1.2: <BTC> at usbus1
ukbd0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
on usbus1
kbd2 at ukbd0
uhid0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
on usbus1
ada0 at ahcich0 bus 0 scbus5 target 0 lun 0
ada0: <Corsair Force 3 SSD 1.3.3> ATA-8 SATA 3.x device
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 85857MB (175836528 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad8
ada1 at ahcich1 bus 0 scbus6 target 0 lun 0
ada1: <OCZ-AGILITY2 1.33> ATA-8 SATA 2.x device
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad10
ada2 at ahcich2 bus 0 scbus7 target 0 lun 0
ada2: <ST31000333AS SD35> ATA-8 SATA 2.x device
ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada2: Previously was known as ad12
da12 at mps2 bus 0 scbus4 target 5 lun 0
da12: <ATA ST1000DL002-9TT1 CC32> Fixed Direct Access SCSI-6 device
da12: 300.000MB/s transfers
da12: Command Queueing enabled
da12: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C)
SMP: AP CPU #2 Launched!
da7 at mps0 bus 0 scbus0 target 7 lun 0
da7: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da7: 300.000MB/s transfers
da7: Command Queueing enabled
da7: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da3 at mps0 bus 0 scbus0 target 3 lun 0
da3: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da3: 300.000MB/s transfers
da3: Command Queueing enabled
da3: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da0 at mps0 bus 0 scbus0 target 0 lun 0
da0: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #4 Launched!
da6 at mps0 bus 0 scbus0 target 6 lun 0
da6: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da6: 300.000MB/s transfers
da6: Command Queueing enabled
da6: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da5 at mps0 bus 0 scbus0 target 5 lun 0
da5: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da5: 300.000MB/s transfers
da5: Command Queueing enabled
da5: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da4 at mps0 bus 0 scbus0 target 4 lun 0
da4: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da4: 300.000MB/s transfers
da4: Command Queueing enabled
da4: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #6 Launched!
da9 at mps2 bus 0 scbus4 target 1 lun 0
da9: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da9: 300.000MB/s transfers
da9: Command Queueing enabled
da9: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da10 at mps2 bus 0 scbus4 target 2 lun 0
da10: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da10: 300.000MB/s transfers
da10: Command Queueing enabled
da10: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da8 at mps2 bus 0 scbus4 target 0 lun 0
da8: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da8: 300.000MB/s transfers
da8: Command Queueing enabled
da8: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #1 Launched!
da11 at mps2 bus 0 scbus4 target 3 lun 0
da11: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da11: 300.000MB/s transfers
da11: Command Queueing enabled
da11: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da1 at mps0 bus 0 scbus0 target 1 lun 0
da1: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da1: 300.000MB/s transfers
da1: Command Queueing enabled
da1: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da2 at mps0 bus 0 scbus0 target 2 lun 0
da2: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da2: 300.000MB/s transfers
da2: Command Queueing enabled
da2: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #3 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #7 Launched!
Timecounter "TSC-low" frequency 15695219 Hz quality 1000
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
Trying to mount root from ufs:/dev/gpt/disk0 [rw]...
ZFS filesystem version 5
ZFS storage pool version 28
(da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0
(da12:mps2:0:5:0): CAM status: SCSI Status Error
(da12:mps2:0:5:0): SCSI status: Check Condition
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
(da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0
(da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional
sense information)
--
Dennis Glatting <dg at pki2.com>
More information about the freebsd-fs
mailing list