kern/136652: [firewire] Firewire-attached "WD My Book 1028" does not mount at boot but is OK if connected after boot.

[Andrew Reilly]

The following reply was made to PR kern/136652; it has been noted by GNATS.

From: Andrew Reilly <areilly at bigpond.net.au>
To: bug-followup at FreeBSD.org, sbruno at FreeBSD.org
Cc: freebsd-firewire at FreeBSD.org
Subject: Re: kern/136652: [firewire] Firewire-attached "WD My Book 1028" does not mount at boot but is OK if connected after boot.
Date: Fri, 16 Apr 2010 11:28:43 +1000

 Hi there,
 
 I'm afraid that this problem is back, now that I'm running -CURRENT.
 
 One extra piece of information that I can add is that I don't
 have to actually power-cycle the drive to make it show up: if I
 run "fwcontrol -r" after boot, then dmesg says:
 
 fwohci0: Initiate bus reset
 fwohci0: fwohci_intr_core: BUS reset
 fwohci0: fwohci_intr_core: node_id=0x00000001, SelfID Count=2, CYCLEMASTER mode
 firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1)  (me) 
 firewire0: bus manager 1 
 sbp0: sbp_show_sdev_info: sbp0:0:0: ordered:1 type:0 EUI:0090a97488ce53aa node:0 speed:3 maxrec:8
 sbp0: sbp_show_sdev_info: sbp0:0:0 'WD' 'My Book' '001028'
 sbp0: sbp_show_sdev_info: sbp0:0:1: ordered:1 type:13 EUI:0090a97488ce53aa node:0 speed:3 maxrec:8
 sbp0: sbp_show_sdev_info: sbp0:0:1 'WD' 'My Book' '001028'
 da0 at sbp0 bus 0 scbus0 target 0 lun 0
 da0: <WD My Book 1028> Fixed Direct Access SCSI-4 device 
 da0: 50.000MB/s transfers
 da0: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C)
 ses0 at sbp0 bus 0 scbus0 target 0 lun 1
 ses0: <WD My Book Device > Fixed Enclosure Services SCSI-4 device 
 ses0: 50.000MB/s transfers
 ses0: SCSI-3 SES Device
 GEOM_JOURNAL: Journal 153133090: da0s1a contains data.
 GEOM_JOURNAL: Journal 153133090: da0s1a contains journal.
 GEOM_JOURNAL: Journal da0s1a clean.
 
 The relevant pieces of boot-time dmesg (from dmesg.boot) are:
 
 fwohci0: <Texas Instruments TSB82AA2> mem 0xf2004000-0xf20047ff,0xf2000000-0xf2003fff irq 18 at device 10.0 on pci1
 fwohci0: [ITHREAD]
 fwohci0: OHCI version 1.10 (ROM=1)
 fwohci0: No. of Isochronous channels is 4.
 fwohci0: EUI64 00:14:85:56:00:e6:80:b0
 fwohci0: invalid speed 7 (fixed to 3).
 fwohci0: Phy 1394a available S800, 3 ports.
 fwohci0: Link S800, max_rec 4096 bytes.
 firewire0: <IEEE1394(FireWire) bus> on fwohci0
 fwe0: <Ethernet over FireWire> on firewire0
 if_fwe0: Fake Ethernet address: 02:14:85:e6:80:b0
 fwe0: Ethernet address: 02:14:85:e6:80:b0
 fwip0: <IP over FireWire> on firewire0
 fwip0: Firewire address: 00:14:85:56:00:e6:80:b0 @ 0xfffe00000000, S800, maxrec 4096
 sbp0: <SBP-2/SCSI over FireWire> on firewire0
 dcons_crom0: <dcons configuration ROM> on firewire0
 dcons_crom0: bus_addr 0x1194000
 fwohci0: Initiate bus reset
 fwohci0: fwohci_intr_core: BUS reset
 fwohci0: fwohci_intr_core: node_id=0x00000001, SelfID Count=1, CYCLEMASTER mode
 
 ...
 
 firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1)  (me) 
 firewire0: bus manager 1 
 fwohci0: phy int
 
 ...
 
 firewire0: New S800 device ID:0090a97488ce53aa
 sbp0: sbp_show_sdev_info: sbp0:0:0: ordered:1 type:0 EUI:0090a97488ce53aa node:0 speed:3 maxrec:8
 sbp0: sbp_show_sdev_info: sbp0:0:0 'WD' 'My Book' '001028'
 sbp0: sbp_show_sdev_info: sbp0:0:1: ordered:1 type:13 EUI:0090a97488ce53aa node:0 speed:3 maxrec:8
 sbp0: sbp_show_sdev_info: sbp0:0:1 'WD' 'My Book' '001028'
 
 
 ...
 
 
 and that's all. da0 doesn't show up until after I manually reset
 the bus (or power-cycle the drive).
 
 Please let me know if there are any other experiments that I can
 run, or information that I can provide that might help diagnose
 the problem.
 
 Cheers,
 
 -- 
 Andrew