wpi make error*

Sun Apr 13 02:44:03 UTC 2008

 I have 20071102-freebsd-wpi.tar.gz install  successfully but this is the ifconfig message

wpi0: flags=8803<UP,BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        ether 00:13:02:bf:92:f8
        media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
        status: no carrier
        ssid "" channel 1 (2412 Mhz 11b)
        authmode OPEN privacy OFF txpower 50 bmiss 7 scanvalid 60 bintval 0

Note that: no carrier.

and dmesg stated

wpi0: <Intel(R) PRO/Wireless 3945ABG> mem 0xd8000000-0xd8000fff irq 17 at device 0.0 on pci3
bus_dmamem_alloc failed to align memory properly.
  ................
bus_dmamem_alloc failed to align memory properly.
wpi0: Ethernet address: 00:13:02:bf:92:f8
wpi0: [ITHREAD]
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpifw: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpifw: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpifw_fw, 0xc4f6d520, 0) error 1
firmware_get: failed to load firmware image wpifw
wpi0: could not load firmware image 'wpifw'
wpi0: A problem occurred loading the firmware to the driver
ukbd0: at uhub2 port 1 (addr 2) disconnected
ukbd0: detached
uhid0: at uhub2 port 1 (addr 2) disconnected
uhid0: detached
ukbd0: <CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 2> on uhub2
kbd2 at ukbd0
uhid0: <CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 2> on uhub2
wpi0: detached
wpi0: <Intel(R) PRO/Wireless 3945ABG> mem 0xd8000000-0xd8000fff irq 17 at device 0.0 on pci3
wpi0: Driver Revision 20071102
wpi0: Hardware Revision (0x801)
bus_dmamem_alloc failed to align memory properly.
.................................
bus_dmamem_alloc failed to align memory properly.
adding chan 1 flags=0x2b maxpwr=15, offset 2
adding chan 2 flags=0x2b maxpwr=15, offset 4
adding chan 3 flags=0x2b maxpwr=15, offset 6
adding chan 4 flags=0x2b maxpwr=15, offset 8
adding chan 5 flags=0x2b maxpwr=15, offset 10
adding chan 6 flags=0x2b maxpwr=15, offset 12
adding chan 7 flags=0x2b maxpwr=15, offset 14
adding chan 8 flags=0x2b maxpwr=15, offset 16
adding chan 9 flags=0x2b maxpwr=15, offset 18
adding chan 10 flags=0x2b maxpwr=15, offset 20
adding chan 11 flags=0x2b maxpwr=14, offset 22
adding chan 36 flags=0xa1 maxpwr=14, offset 23
adding chan 40 flags=0xa1 maxpwr=14, offset 24
adding chan 44 flags=0xa1 maxpwr=14, offset 25
adding chan 48 flags=0xa1 maxpwr=14, offset 26
adding chan 52 flags=0xb1 maxpwr=14, offset 27
adding chan 56 flags=0xb1 maxpwr=14, offset 28
adding chan 60 flags=0xb1 maxpwr=14, offset 29
adding chan 64 flags=0xb1 maxpwr=14, offset 30
adding chan 149 flags=0x21 maxpwr=16, offset 31
adding chan 153 flags=0x21 maxpwr=16, offset 32
adding chan 157 flags=0x21 maxpwr=16, offset 33
adding chan 161 flags=0x21 maxpwr=16, offset 34
adding chan 165 flags=0x21 maxpwr=16, offset 35
power group 0: chan=1 maxpwr=47 temp=-187
        sample 0: index=13 power=43
        sample 1: index=29 power=30
        sample 2: index=47 power=10
        sample 3: index=58 power=-1
        sample 4: index=77 power=-19
power group 1: chan=44 maxpwr=51 temp=-191
        sample 0: index=12 power=42
        sample 1: index=19 power=35
        sample 2: index=32 power=21
        sample 3: index=43 power=11
        sample 4: index=77 power=-22
power group 2: chan=64 maxpwr=51 temp=-189
        sample 0: index=12 power=43
        sample 1: index=20 power=35
        sample 2: index=33 power=22
        sample 3: index=44 power=13
        sample 4: index=77 power=-18
power group 3: chan=116 maxpwr=48 temp=-188
        sample 0: index=12 power=36
        sample 1: index=20 power=27
        sample 2: index=36 power=11
        sample 3: index=48 power=0
        sample 4: index=77 power=-27
power group 4: chan=153 maxpwr=48 temp=-186
        sample 0: index=10 power=35
        sample 1: index=20 power=23
        sample 2: index=32 power=11
        sample 3: index=42 power=3
        sample 4: index=77 power=-28
wpi0: Regulatory Domain: MoW1
wpi0: Hardware Type: B
wpi0: Hardware Revision: ?
wpi0: SKU does support 802.11a
wpi0: Ethernet address: 00:13:02:bf:92:f8
wpi0: [ITHREAD]
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: timeout resetting Tx ring 1
wpi0: timeout resetting Tx ring 3
wpi0: timeout resetting Tx ring 4
NEWSTATE:INIT
firmware_get: failed to load firmware image wpifw
wpi0: could not load firmware image 'wpifw'
wpi0: A problem occurred loading the firmware to the driver
NEWSTATE:INIT
firmware_get: failed to load firmware image wpifw
wpi0: could not load firmware image 'wpifw'
wpi0: A problem occurred loading the firmware to the driver

While i have this in my loader.conf 

if_ath_load["YES"
if_wpi_load="YES"
wlan_load="YES"
wlan_wep_load="YES"
wlan_ccmp_load="YES"
wlan_tkip_load="YES"
legal.intel_wpi.license_ack=1
wpifw_load="YES"

but why it still ask me to set the license?

_________________________________________________________________
Help Splitzo Sally Before It’s Too Late! 
http://www.thegirlwhosplitinto5.com/