Continuous timeout messages from 10.0 alpha4

[Mark Johnston]

Rebuilding sysutils/hal should fix this problem. It's been reported several
times in the past week or two, and rebuilding this port fixed it for me
when I ran into it.


On Mon, Oct 7, 2013 at 3:25 PM, Shane Ambler <BSD at shaneware.biz> wrote:

> Resending to current
>
> This is a regression between alpha2 and alpha4. I first setup a disk to
> boot 10 just after alpha2 was tagged. A few days ago I updated to
> alpha4 and started getting timeout messages, I have just built alpha5
> r256098 and still get them.
>
> I just had 10 running for a few hours and 3 of the messages log archives
> which syslog rotates each hour due to size contain 3370 2508 and 3162
> timeout messages over 3 hours uptime.
>
> each entry is similar to --
> Oct  7 19:00:02 leader kernel: ahcich1: Timeout on slot 15 port 0
> Oct  7 19:00:02 leader kernel: ahcich1: is 40000001 cs 00008000 ss
> 00000000 rs 00008000 tfd 2451 serr 00000000 cmd 00004f17
>
> With slot x cycling from 0-31 but not always in sequence.
>
> MB is ASUS P8H61M LE/USB3 - corei5 - 8MB - nvidia GT520
>
> ahci0: <Intel Cougar Point AHCI SATA controller> port
> 0xf070-0xf077,0xf060-0xf063,**0xf050-0xf057,0xf040-0xf043,**0xf020-0xf03f
> mem 0xfb305000-0xfb3057ff irq 20 at device 31.2 on pci0
> ahci0: AHCI v1.30 with 4 3Gbps ports, Port Multiplier not supported
>
> With the following connected to ahcich1 (LG blu-ray burner)
> cd0 at ahcich1 bus 0 scbus1 target 0 lun 0
> cd0: <HL-DT-ST BD-RE  BH12LS38 1.00> Removable CD-ROM SCSI-0 device
>
>
>
> Most relevant dmesg info would be (full dmesg/logs available) --
>
> ahci0: <Intel Cougar Point AHCI SATA controller> port
> 0xf070-0xf077,0xf060-0xf063,**0xf050-0xf057,0xf040-0xf043,**0xf020-0xf03f
> mem 0xfb305000-0xfb3057ff irq 20 at device 31.2 on pci0
> ahci0: AHCI v1.30 with 4 3Gbps ports, Port Multiplier not supported
> ahcich0: <AHCI channel> at channel 0 on ahci0
> ahcich1: <AHCI channel> at channel 1 on ahci0
> ahcich4: <AHCI channel> at channel 4 on ahci0
> ahcich5: <AHCI channel> at channel 5 on ahci0
> ahciem0: <AHCI enclosure management bridge> on ahci0
>
> ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
> ada0: <WDC WD20EARX-00PASB0 51.0AB51> ATA-8 SATA 3.x device
> ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada0: Command Queueing enabled
> ada0: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
> ada0: quirks=0x1<4K>
> ada0: Previously was known as ad4
> ada1 at ahcich4 bus 0 scbus2 target 0 lun 0
> ada1: <WDC WD10EARS-00Y5B1 80.00A80> ATA-8 SATA 2.x device
> ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada1: Command Queueing enabled
> ada1: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
> ada1: quirks=0x1<4K>
> ada1: Previously was known as ad8
> ada2 at ahcich5 bus 0 scbus3 target 0 lun 0
> ada2: <eSATA-2 WD800JD-23JNA1 06.01C06> ATA-6 SATA 2.x device
> ada2: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 512bytes)
> ada2: 76324MB (156312576 512 byte sectors: 16H 63S/T 16383C)
> ada2: Previously was known as ad10
> ses0 at ahciem0 bus 0 scbus4 target 0 lun 0
> ses0: <AHCI SGPIO Enclosure 1.00 0001> SEMB S-E-S 2.00 device
> ses0: SEMB SES Device
> ______________________________**_________________
> freebsd-current at freebsd.org mailing list
> http://lists.freebsd.org/**mailman/listinfo/freebsd-**current<http://lists.freebsd.org/mailman/listinfo/freebsd-current>
> To unsubscribe, send any mail to "freebsd-current-unsubscribe@**
> freebsd.org <freebsd-current-unsubscribe at freebsd.org>"
>