xpt_action_default: CCB type 0xe not supported

Tue Jun 21 17:51:04 UTC 2011

Fresh installation and after world && kernel update I get these messages
during boot:

xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported

The system is running GENERIC with debugging for use in current off options.

Full dmesg attached.

Regards,

-- 
George Kontostanos
aisecure.net <http://www.aisecure.net>
-------------- next part --------------
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-CURRENT #0: Tue Jun 21 19:28:33 EEST 2011
    root at core2duo.aicom.loc:/usr/obj/usr/src/sys/GENERIC amd64
CPU: Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz (2401.97-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x6f6  Family = 6  Model = f  Stepping = 6
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant, performance statistics
real memory  = 4294967296 (4096 MB)
avail memory = 4057284608 (3869 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <MSTEST OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <MSTEST TESTONLY> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7ff00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
ACPI Warning: Incorrect checksum in table [OEMB] - 0xE7, should be 0xDA (20110527/tbutils-282)
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x9c00-0x9c7f mem 0xfd000000-0xfdffffff,0xc0000000-0xcfffffff,0xfc000000-0xfcffffff irq 16 at device 0.0 on pci1
uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0xdc00-0xdc1f irq 16 at device 26.0 on pci0
uhci0: LegSup = 0x2f00
usbus0: <Intel 82801H (ICH8) USB controller USB-D> on uhci0
uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0xe000-0xe01f irq 17 at device 26.1 on pci0
uhci1: LegSup = 0x2f00
usbus1: <Intel 82801H (ICH8) USB controller USB-E> on uhci1
ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem 0xfebffc00-0xfebfffff irq 18 at device 26.7 on pci0
usbus2: EHCI version 1.0
usbus2: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> on ehci0
hdac0: <Intel 82801H High Definition Audio Controller> mem 0xfebf8000-0xfebfbfff irq 22 at device 27.0 on pci0
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci4: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci3: <ACPI PCI bus> on pcib3
re0: <RealTek 8168/8111 B/C/CP/D/DP/E PCIe Gigabit Ethernet> port 0xb800-0xb8ff mem 0xfeaff000-0xfeafffff irq 19 at device 0.0 on pci3
re0: Using 1 MSI message
re0: Chip rev. 0x38000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 00:18:f3:03:66:7e
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci2: <ACPI PCI bus> on pcib4
atapci0: <JMicron JMB363 UDMA133 controller> port 0xac00-0xac07,0xa880-0xa883,0xa800-0xa807,0xa480-0xa483,0xa400-0xa40f mem 0xfe9fe000-0xfe9fffff irq 16 at device 0.0 on pci2
ahci0: <JMicron JMB363 AHCI SATA controller> on atapci0
ahci0: AHCI v1.00 with 2 3Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ata2: <ATA channel 0> on atapci0
uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0xd480-0xd49f irq 23 at device 29.0 on pci0
uhci2: LegSup = 0x2f00
usbus3: <Intel 82801H (ICH8) USB controller USB-A> on uhci2
uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0xd800-0xd81f irq 19 at device 29.1 on pci0
uhci3: LegSup = 0x2f00
usbus4: <Intel 82801H (ICH8) USB controller USB-B> on uhci3
uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0xd880-0xd89f irq 18 at device 29.2 on pci0
uhci4: LegSup = 0x2f00
usbus5: <Intel 82801H (ICH8) USB controller USB-C> on uhci4
ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem 0xfebff800-0xfebffbff irq 23 at device 29.7 on pci0
usbus6: EHCI version 1.0
usbus6: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> on ehci1
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH8 SATA300 controller> port 0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe40f,0xe080-0xe08f irq 19 at device 31.2 on pci0
ata3: <ATA channel 0> on atapci1
ata4: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci2: <Intel ICH8 SATA300 controller> port 0xd400-0xd407,0xd080-0xd083,0xd000-0xd007,0xcc00-0xcc03,0xc880-0xc88f,0xc800-0xc80f irq 19 at device 31.5 on pci0
ata5: <ATA channel 0> on atapci2
ata6: <ATA channel 1> on atapci2
acpi_button0: <Power Button> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
Timecounters tick every 1.000 msec
hdac0: HDA Codec #0: Analog Devices AD1988A
pcm0: <HDA Analog Devices AD1988A PCM #0 Analog> at cad 0 nid 1 on hdac0
pcm1: <HDA Analog Devices AD1988A PCM #1 Analog> at cad 0 nid 1 on hdac0
pcm2: <HDA Analog Devices AD1988A PCM #2 Digital> at cad 0 nid 1 on hdac0
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
ada0 at ata3 bus 0 scbus3 target 0 lun 0
ada0: <WDC WD2500KS-00MJB0 02.01C03> ATA-7 SATA 2.x device
ada0: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes)
ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad10
ada1 at ata5 bus 0 scbus5 target 0 lun 0
ada1: <Maxtor 6L080M0 BACE1G10> ATA-7 SATA 1.x device
ada1: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada1: 76319MB (156301488 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad14
ada2 at ata6 bus 0 scbus6 target 0 lun 0
ada2: <Maxtor 6L080M0 BANC1G10> ATA-7 SATA 1.x device
ada2: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada2: 76319MB (156301488 512 byte sectors: 16H 63S/T 16383C)
ada2: Previously was known as ad16
xpt_action_default: CCB type 0xe not supported
cd0 at ata2 bus 0 scbus2 target 0 lun 0
cd0: <ASUS DVD-E616A2 1.03> Removable CD-ROM SCSI-0 device 
cd0: 100.000MB/s transfers (UDMA5, ATAPI 12bytes, PIO 65534bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
SMP: AP CPU #1 Launched!
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
Timecounter "TSC-low" frequency 9382688 Hz quality 1000
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
uhub2: 4 ports with 4 removable, self powered
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
Root mount waiting for: usbus6 usbus2
uhub6: 6 ports with 6 removable, self powered
Root mount waiting for: usbus6
ugen0.2: <HP> at usbus0
ulpt0: <HP Officejet 4300 series, class 0/0, rev 2.00/1.00, addr 2> on usbus0
ulpt0: using bi-directional mode
ugen6.2: <HLDS Inc> at usbus6
umass0: <HLDS Inc SuperMulti RW, class 0/0, rev 2.00/1.55, addr 2> on usbus6
umass0:  8070i (ATAPI) over Bulk-Only; quirks = 0x0000
Root mount waiting for: usbus6
umass0:7:0:-1: Attached to scbus7
Trying to mount root from ufs:/dev/ada1p2 [rw]...
(probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: NOT READY csi:3a,0,bb,0 asc:3a,0 (Medium not present)
cd1 at umass-sim0 bus 0 scbus7 target 0 lun 0
cd1: <HL-DT-ST BD-RE  BE06LU10 YE03> Removable CD-ROM SCSI-0 device 
cd1: 40.000MB/s transfers
cd1: Attempt to query device size failed: NOT READY, Medium not present
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
xpt_action_default: CCB type 0xe not supported
re0: link state changed to UP