panic in 8.0-CURRENT after svn from r189900 to r190389
Goran Gajic
ggajic at afrodita.rcub.bg.ac.yu
Tue Mar 24 13:55:17 PDT 2009
Hi,
Today I have svn up my FreeBSD-8.0-CURRENT to r190389 but it is no
longer able to boot, it panics at boot. Here is message I'm getting (I had
to write it down to paper :( since I don't have serial attached to this
machine:
Fatal trap 12: page fault while in kernel mode
cpuid =0, apic id = 00
fault virtual address = 0x3c
Fault code = supervisor write data, page not present
Instruction ponter = 0x8: 0xffffffff8056db9f
Stack ponter = 0x10: 0xffffffff813bac70
Code segment = 0x10: 0xffffffff813baca0
= base 0x0, limit 0xfffff, type 0x1b
DPL 0, pres 1, long 1, def32 0, gran 1
Processor eflags = resume, iopl = 0
Current process = 0 (swapper)
[thread pio 0 tid 10000]
stopped at devclass_find_interna+0x10f: orl $0x1, 0x3c(%rax)
db> where
tracing pid 0 tid 10000 td 0xffffffff80bb5ce0
dev_class_find_internal() at devclass_find_internal+0x10f
driver_module_handler() at driver_module_handler+0xb9
module_register_init() at module_register_init+0x7d
mi_startup() at mi_startup+0x59
btext() at btext+0x2c
db>
And here is dmesg from last working kernel I have:
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #0 r189900: Mon Mar 16 22:51:40 CET 2009
root at magarac:/usr/src/sys/amd64/compile/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Quad CPU Q8200 @ 2.33GHz (2333.08-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x10677 Stepping = 7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x8e39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
Cores per package: 4
usable memory = 1056894976 (1007 MB)
avail memory = 1018724352 (971 MB)
ACPI APIC Table: <A_M_I_ OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <A_M_I_ OEMRSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 3ff00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xa000-0xa0ff mem 0xd0000000-0xdfffffff,0xfbae0000-0xfbaeffff irq 16 at device 0.0 on pci1
pci1: <multimedia, HDA> at device 0.1 (no driver attached)
uhci0: <Intel 82801I (ICH9) USB controller> port 0x9800-0x981f irq 16 at device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x0f30
usbus0: <Intel 82801I (ICH9) USB controller> on uhci0
uhci1: <Intel 82801I (ICH9) USB controller> port 0x9880-0x989f irq 21 at device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x0f30
usbus1: <Intel 82801I (ICH9) USB controller> on uhci1
uhci2: <Intel 82801I (ICH9) USB controller> port 0x9c00-0x9c1f irq 18 at device 26.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x0f30
usbus2: <Intel 82801I (ICH9) USB controller> on uhci2
ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfb9ffc00-0xfb9fffff irq 18 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci5: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci5
pci7: <ACPI PCI bus> on pcib3
amr0: <LSILogic MegaRAID 1.53> mem 0xfaff0000-0xfaffffff irq 18 at device 2.0 on pci7
amr0: Using 64-bit DMA
amr0: [ITHREAD]
amr0: delete logical drives supported by controller
amr0: <LSILogic PERC 4/SC> Firmware 352D, BIOS 1.10, 64MB RAM
pcib4: <PCI-PCI bridge> mem 0xfbeffc00-0xfbeffc7f irq 16 at device 0.1 on pci5
pci6: <PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci4: <ACPI PCI bus> on pcib5
mskc0: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfbdfc000-0xfbdfffff irq 18 at device 0.0 on pci4
msk0: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x03> on mskc0
can't re-use a leaf (jabbers)!
msk0: Ethernet address: 00:1d:60:c9:1a:3e
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
mskc0: [FILTER]
pcib6: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci3: <ACPI PCI bus> on pcib6
mskc1: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0xc800-0xc8ff mem 0xfbcfc000-0xfbcfffff irq 19 at device 0.0 on pci3
msk1: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x03> on mskc1
can't re-use a leaf (jabbers)!
msk1: Ethernet address: 00:1d:60:c9:17:a3
miibus1: <MII bus> on msk1
e1000phy1: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus1
e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
mskc1: [FILTER]
pcib7: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0
pci2: <ACPI PCI bus> on pcib7
atapci0: <Marvell 88SX6145 UDMA133 controller> port 0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb807,0xb480-0xb483,0xb400-0xb40f mem 0xfbbffc00-0xfbbfffff irq 16 at device 0.0 on pci2
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
uhci3: <Intel 82801I (ICH9) USB controller> port 0x9080-0x909f irq 23 at device 29.0 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x0f30
usbus4: <Intel 82801I (ICH9) USB controller> on uhci3
uhci4: <Intel 82801I (ICH9) USB controller> port 0x9400-0x941f irq 19 at device 29.1 on pci0
uhci4: [ITHREAD]
uhci4: LegSup = 0x0f30
usbus5: <Intel 82801I (ICH9) USB controller> on uhci4
uhci5: <Intel 82801I (ICH9) USB controller> port 0x9480-0x949f irq 18 at device 29.2 on pci0
uhci5: [ITHREAD]
uhci5: LegSup = 0x0f30
usbus6: <Intel 82801I (ICH9) USB controller> on uhci5
ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfb9ff800-0xfb9ffbff irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <Intel 82801I (ICH9) USB 2.0 controller> on ehci1
pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci8: <ACPI PCI bus> on pcib8
pci8: <multimedia, video> at device 0.0 (no driver attached)
pci8: <multimedia> at device 0.2 (no driver attached)
fwohci0: <VIA Fire II (VT6306)> port 0xec00-0xec7f mem 0xfebff800-0xfebfffff irq 19 at device 3.0 on pci8
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:d8:00:01:8a:3e:e5
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x3e210000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:d8:8a:3e:e5
fwe0: Ethernet address: 02:11:d8:8a:3e:e5
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:11:d8:00:01:8a:3e:e5 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH9 SATA300 controller> port 0x8000-0x8007,0x7c00-0x7c03,0x7880-0x7887,0x7800-0x7803,0x7480-0x748f,0x7400-0x740f irq 22 at device 31.2 on pci0
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci1
ata5: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci2: <Intel ICH9 SATA300 controller> port 0x9000-0x9007,0x8c00-0x8c03,0x8880-0x8887,0x8800-0x8803,0x8480-0x848f,0x8400-0x840f irq 22 at device 31.5 on pci0
atapci2: [ITHREAD]
ata6: <ATA channel 0> on atapci2
ata6: [ITHREAD]
ata7: <ATA channel 1> on atapci2
ata7: [ITHREAD]
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 on acpi0
uart0: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
cpu0: <ACPI CPU> on acpi0
ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] - D, should be 4 [20070320]
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
cpu2: <ACPI CPU> on acpi0
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
cpu3: <ACPI CPU> on acpi0
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
ppc0: cannot reserve I/O port range
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
firewire0: bus manager 0
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
acd0: DVDR <NEC DVD RW ND-4550A/1.09> at ata2-master UDMA33
amr0: delete logical drives supported by controller
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 209640MB (429342720 sectors) RAID 0 (optimal)
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
ugen6.2: <Logitech> at usbus6
ums0: <Logitech USB-PS/2 Optical Mouse, class 0/0, rev 2.00/20.00, addr 2> on usbus6
ums0: 3 buttons and [XYZ] coordinates
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from ufs:/dev/amrd0s2a
lock order reversal:
1st 0xfffffffe54a663d8 bufwait (bufwait) @ kern/vfs_bio.c:2549
2nd 0xffffff00019d0a00 dirhash (dirhash) @ ufs/ufs/ufs_dirhash.c:275
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2a
_witness_debugger() at _witness_debugger+0x2e
witness_checkorder() at witness_checkorder+0x81e
_sx_xlock() at _sx_xlock+0x55
ufsdirhash_acquire() at ufsdirhash_acquire+0x33
ufsdirhash_add() at ufsdirhash_add+0x19
ufs_direnter() at ufs_direnter+0x88b
ufs_mkdir() at ufs_mkdir+0x633
VOP_MKDIR_APV() at VOP_MKDIR_APV+0x93
kern_mkdirat() at kern_mkdirat+0x2b2
syscall() at syscall+0x1bf
Xfast_syscall() at Xfast_syscall+0xab
--- syscall (136, FreeBSD ELF64, mkdir), rip = 0x80071e85c, rsp = 0x7fffffffed18, rbp = 0x7fffffffef7e ---
KLD snd_hda.ko: depends on kernel - not available
linker_load_file: Unsupported file type
KLD linux.ko: depends on kernel - not available
linker_load_file: Unsupported file type
msk0: link state changed to UP
Regards,
gg.
More information about the freebsd-current
mailing list