Annoying whitenoise sound coming from snd_hda enabled chipset
Yoshihiro Ota
ota at j.email.ne.jp
Wed Feb 25 18:17:09 PST 2009
On Tue, 24 Feb 2009 21:57:27 +0200
Alexander Motin <mav at FreeBSD.org> wrote:
> Yoshihiro Ota wrote:
> > In my case, with hdac or pcm device, 8-CURRENT fails to boot very requentry.
> > It fails to prove a device and doesn't proceed farthar than that point.
> > Now it only boots once in 5 or 10 reboots.
> >
> > When it boots, it prints lots of following messages.
> >
> > hdac0: HDA Codec #0: Conexant CX20549 (Venice)
> > hdac0: unable to allocate widgets!
> > hdac0: unable to allocate widgets!
> > hdac0: unable to allocate widgets!
> > hdac0: unable to allocate widgets!
> > hdac0: unable to allocate widgets!
> > hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> > hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> > hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> > hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> > hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> >
> > I think this started happening about a week ago or so, sometime between
> > 13 and 16th.
>
> The only significant change last time was enabling MSI by default. But I
> don't think it should lead to such errors. I have tried even operation
> completely without interrupts working and there is not such errors. Can
> you send me complete verbose dmesg with the problem and `pciconf -lvc`
> output?
>
> Also you may try to disable MSI by setting 'hint.hdac.0.msi=0' hint.
Once I disabled snd_hda_load="YES" in /boot/loader.conf, it comes up
all times. However, when I run "kldload snd_hda", the system stops responding,
i.e. crashes.
So, now I added 'hint.hdac.0.msi="0"' in the hint; then, system comes up fine.
I tried "kldload snd_hda" and got the following output.
System didn't crash after adding the hint so that I added snd_hda_load="YES"
back to /boot/loader.conf.
I also attached piconf and dmesg.
Regards,
Hiro
hdac0: <NVidia MCP51 High Definition Audio Controller> mem 0xb0000000-0xb0003fff
irq 21 at device 16.1 on pci0
hdac0: HDA Driver Revision: 20090215_0128
hdac0: [ITHREAD]
hdac0: HDA Codec #0: Conexant CX20549 (Venice)
pcm0: <HDA Conexant CX20549 (Venice) PCM #0 Analog> at cad 0 nid 1 on hdac0
pcm1: <HDA Conexant CX20549 (Venice) PCM #1 Digital> at cad 0 nid 1 on hdac0
-------------- next part --------------
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #4 r189024M: Wed Feb 25 09:32:27 EST 2009
root at xxx:/usr/obj/amd64/usr/src/head/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff810ac000.
Preloaded elf obj module "/boot/kernel/geom_concat.ko" at 0xffffffff810ac1f8.
Preloaded elf obj module "/boot/kernel/geom_uzip.ko" at 0xffffffff810ac868.
Preloaded elf obj module "/boot/kernel/zlib.ko" at 0xffffffff810ace58.
Preloaded elf obj module "/boot/kernel/snd_hda.ko" at 0xffffffff810ad400.
Preloaded elf obj module "/boot/kernel/sound.ko" at 0xffffffff810ada28.
Preloaded elf obj module "/boot/kernel/wlan_xauth.ko" at 0xffffffff810ae0d0.
Preloaded elf obj module "/boot/kernel/wlan_acl.ko" at 0xffffffff810ae6c0.
Preloaded elf obj module "/boot/kernel/smb.ko" at 0xffffffff810aed70.
Preloaded elf obj module "/boot/kernel/smbus.ko" at 0xffffffff810af298.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1908702688 Hz
CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-58 (1908.70-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0x60f81 Stepping = 1
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x2001<SSE3,CX16>
AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch>
Cores per package: 2
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
usable memory = 1525403648 (1454 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x0000000000099fff, 626688 bytes (153 pages)
0x00000000010dc000 - 0x000000005966efff, 1482240000 bytes (361875 pages)
avail memory = 1472200704 (1404 MB)
ACPI APIC Table: <HP APIC >
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
ULE: setup cpu 0
ULE: setup cpu 1
ACPI: RSDP @ 0x0xf88f0/0x0014 (v 0 HP )
ACPI: RSDT @ 0x0x5bf0bb25/0x0040 (v 1 HPQOEM SLIC-MPC 0x06040000 LTP 0x00000000)
ACPI: FACP @ 0x0x5bf14b16/0x0074 (v 1 HP MCP51M 0x06040000 PTL_ 0x000F4240)
ACPI: DSDT @ 0x0x5bf0bb65/0x8FB1 (v 1 HP MCP51M 0x06040000 MSFT 0x03000000)
ACPI: FACS @ 0x0x5bf15fc0/0x0040
ACPI: SSDT @ 0x0x5bf14b8a/0x0206 (v 1 PTLTD POWERNOW 0x06040000 LTP 0x00000001)
ACPI: MCFG @ 0x0x5bf14d90/0x003C (v 1 HP MCFG 0x06040000 LTP 0x00000000)
ACPI: HPET @ 0x0x5bf14dcc/0x0038 (v 1 PTLTD HPETTBL 0x06040000 LTP 0x00000001)
ACPI: APIC @ 0x0x5bf14e04/0x005E (v 1 HP APIC 0x06040000 LTP 0x00000000)
ACPI: BOOT @ 0x0x5bf14e62/0x0028 (v 1 HP $SBFTBL$ 0x06040000 LTP 0x00000001)
ACPI: SLIC @ 0x0x5bf14e8a/0x0176 (v 1 HPQOEM SLIC-MPC 0x06040000 LTP 0x00000001)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0: intpin 9 polarity: low
ioapic0: intpin 9 trigger: level
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00000400
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_buffersize=16384 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
wlan: <802.11 Link Layer>
wlan: mac acl policy registered
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
nfslock: pseudo-device
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
io: <I/O>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Feb 24 2009 10:12:34)
acpi0: <HPQOEM SLIC-MPC> on motherboard
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.LPC0.P44_ -> bus 0 dev 10 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.SMB0.P60_ -> bus 0 dev 10 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.SMB0.P64_ -> bus 0 dev 10 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.SMB0.P68_ -> bus 0 dev 10 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.SMB0.SBA2 -> bus 0 dev 10 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.LPC0.P74_ -> bus 0 dev 10 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.XVR2.PCE1 -> bus 0 dev 2 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.LPC0.PIRQ -> bus 0 dev 10 func 0
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 0/360 1/1 -> 9
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 5
Validation 0 255 N 0 5
After Disable 0 255 N 0 5
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 7
Validation 0 255 N 0 7
After Disable 0 255 N 0 7
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 10
Validation 0 255 N 0 10
After Disable 0 255 N 0 10
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 11
Validation 0 255 N 0 11
After Disable 0 255 N 0 11
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 16
Validation 0 255 N 0 16
After Disable 0 255 N 0 16
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 17
Validation 0 255 N 0 17
After Disable 0 255 N 0 17
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 18
Validation 0 255 N 0 18
After Disable 0 255 N 0 18
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 19
Validation 0 255 N 0 19
After Disable 0 255 N 0 19
pci_link8: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 10
Validation 0 10 N 0 10
After Disable 0 255 N 0 10
pci_link9: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 11
Validation 0 255 N 0 11
After Disable 0 255 N 0 11
pci_link10: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 22
Validation 0 255 N 0 22
After Disable 0 255 N 0 22
pci_link11: Index IRQ Rtd Ref IRQs
Initial Probe 0 7 N 0 22
Validation 0 255 N 0 22
After Disable 0 255 N 0 22
pci_link12: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 20
Validation 0 255 N 0 20
After Disable 0 255 N 0 20
pci_link13: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 21
Validation 0 255 N 0 21
After Disable 0 255 N 0 21
pci_link14: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 21
Validation 0 255 N 0 21
After Disable 0 255 N 0 21
pci_link15: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 21
Validation 0 255 N 0 21
After Disable 0 255 N 0 21
pci_link16: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 21
Validation 0 255 N 0 21
After Disable 0 255 N 0 21
pci_link17: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 23
Validation 0 255 N 0 23
After Disable 0 255 N 0 23
pci_link18: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 20
Validation 0 255 N 0 20
After Disable 0 255 N 0 20
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x10de rev: 0x1 num: 2 hz: 25000000 opts: legacy_route
Timecounter "HPET" frequency 25000000 Hz quality 900
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.10.INTA at func 1: 10
ACPI: Found matching pin for 0.10.INTB at func 3: 10
pci_link9: BIOS IRQ 10 for 0.10.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x10de, dev=0x02f0, revid=0xa2
domain=0, bus=0, slot=0, func=0
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x02fa, revid=0xa2
domain=0, bus=0, slot=0, func=1
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x02fe, revid=0xa2
domain=0, bus=0, slot=0, func=2
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x02f8, revid=0xa2
domain=0, bus=0, slot=0, func=3
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x02f9, revid=0xa2
domain=0, bus=0, slot=0, func=4
class=05-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x02ff, revid=0xa2
domain=0, bus=0, slot=0, func=5
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x027f, revid=0xa2
domain=0, bus=0, slot=0, func=6
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x027e, revid=0xa2
domain=0, bus=0, slot=0, func=7
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x02fc, revid=0xa1
domain=0, bus=0, slot=2, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
found-> vendor=0x10de, dev=0x02fd, revid=0xa1
domain=0, bus=0, slot=3, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
found-> vendor=0x10de, dev=0x0244, revid=0xa2
domain=0, bus=0, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 32, base 0xb2000000, size 24, enabled
map[14]: type Prefetchable Memory, range 64, base 0xc0000000, size 28, enabled
map[1c]: type Memory, range 64, base 0xb1000000, size 24, enabled
pcib0: matched entry for 0.5.INTA (src \\_SB_.PCI0.LK3E:0)
pci_link6: Picked IRQ 18 with weight 0
ioapic0: Changing polarity for pin 18 to high
pcib0: slot 5 INTA routed to irq 18 via \\_SB_.PCI0.LK3E
found-> vendor=0x10de, dev=0x0270, revid=0xa2
domain=0, bus=0, slot=9, func=0
class=05-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x0260, revid=0xa3
domain=0, bus=0, slot=10, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type I/O Port, range 32, base 0x1d00, size 7, enabled
found-> vendor=0x10de, dev=0x0264, revid=0xa3
domain=0, bus=0, slot=10, func=1
class=0c-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[20]: type I/O Port, range 32, base 0x3040, size 6, enabled
map[24]: type I/O Port, range 32, base 0x3000, size 6, enabled
pcib0: matched entry for 0.10.INTA (src \\_SB_.PCI0.LSMB:0)
ioapic0: Changing trigger for pin 10 to level
pcib0: slot 10 INTA routed to irq 10 via \\_SB_.PCI0.LSMB
found-> vendor=0x10de, dev=0x0271, revid=0xa3
domain=0, bus=0, slot=10, func=3
class=0b-40-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=b, irq=10
map[10]: type Memory, range 32, base 0xb0040000, size 18, enabled
pcib0: matched entry for 0.10.INTB (src \\_SB_.PCI0.LPMU:0)
pci_link9: Picked IRQ 9 with weight 0
ioapic0: Changing polarity for pin 9 to high
pcib0: slot 10 INTB routed to irq 9 via \\_SB_.PCI0.LPMU
found-> vendor=0x10de, dev=0x026d, revid=0xa3
domain=0, bus=0, slot=11, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xb0004000, size 12, enabled
pcib0: matched entry for 0.11.INTA (src \\_SB_.PCI0.LUS0:0)
pci_link10: Picked IRQ 22 with weight 0
ioapic0: Changing polarity for pin 22 to high
pcib0: slot 11 INTA routed to irq 22 via \\_SB_.PCI0.LUS0
found-> vendor=0x10de, dev=0x026e, revid=0xa3
domain=0, bus=0, slot=11, func=1
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=b, irq=7
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xb0005000, size 8, enabled
pcib0: matched entry for 0.11.INTB (src \\_SB_.PCI0.LUS2:0)
pci_link11: Picked IRQ 22 with weight 1
pcib0: slot 11 INTB routed to irq 22 via \\_SB_.PCI0.LUS2
found-> vendor=0x10de, dev=0x0265, revid=0xf1
domain=0, bus=0, slot=13, func=0
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type I/O Port, range 32, base 0x3080, size 4, enabled
found-> vendor=0x10de, dev=0x0266, revid=0xf1
domain=0, bus=0, slot=14, func=0
class=01-01-85, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
MSI supports 4 messages, 64 bit
map[10]: type I/O Port, range 32, base 0x30c0, size 3, enabled
map[14]: type I/O Port, range 32, base 0x30b4, size 2, enabled
map[18]: type I/O Port, range 32, base 0x30b8, size 3, enabled
map[1c]: type I/O Port, range 32, base 0x30b0, size 2, enabled
map[20]: type I/O Port, range 32, base 0x3090, size 4, enabled
map[24]: type Memory, range 32, base 0xb0006000, size 12, memory disabled
pcib0: matched entry for 0.14.INTA (src \\_SB_.PCI0.LTID:0)
pci_link17: Picked IRQ 23 with weight 0
ioapic0: Changing polarity for pin 23 to high
pcib0: slot 14 INTA routed to irq 23 via \\_SB_.PCI0.LTID
found-> vendor=0x10de, dev=0x026f, revid=0xa2
domain=0, bus=0, slot=16, func=0
class=06-04-01, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x02 (500 ns)
found-> vendor=0x10de, dev=0x026c, revid=0xa2
domain=0, bus=0, slot=16, func=1
class=04-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x05 (1250 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit, vector masks
map[10]: type Memory, range 32, base 0xb0000000, size 14, enabled
pcib0: matched entry for 0.16.INTB (src \\_SB_.PCI0.LAZA:0)
pci_link13: Picked IRQ 21 with weight 0
ioapic0: Changing polarity for pin 21 to high
pcib0: slot 16 INTB routed to irq 21 via \\_SB_.PCI0.LAZA
found-> vendor=0x10de, dev=0x0269, revid=0xa3
domain=0, bus=0, slot=20, func=0
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x01 (250 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xb0008000, size 12, enabled
map[14]: type I/O Port, range 32, base 0x30e0, size 3, enabled
pcib0: matched entry for 0.20.INTA (src \\_SB_.PCI0.LMAC:0)
pci_link12: Picked IRQ 20 with weight 0
ioapic0: Changing polarity for pin 20 to high
pcib0: slot 20 INTA routed to irq 20 via \\_SB_.PCI0.LMAC
found-> vendor=0x1022, dev=0x1100, revid=0x00
domain=0, bus=0, slot=24, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
domain=0, bus=0, slot=24, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
domain=0, bus=0, slot=24, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
domain=0, bus=0, slot=24, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0: <memory, RAM> at device 0.0 (no driver attached)
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
pci0: <memory, RAM> at device 0.6 (no driver attached)
pci0: <memory, RAM> at device 0.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x4000-0x4fff
pcib1: memory decode 0xb4000000-0xb5ffffff
pcib1: prefetched decode 0xd0000000-0xd01fffff
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pcib2: domain 0
pcib2: secondary bus 3
pcib2: subordinate bus 3
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xb6000000-0xb7ffffff
pcib2: no prefetched decode
pci3: <ACPI PCI bus> on pcib2
pci3: domain=0, physical bus=3
found-> vendor=0x14e4, dev=0x4311, revid=0x02
domain=0, bus=3, slot=0, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 64, base 0xb6000000, size 14, enabled
pcib2: requested memory range 0xb6000000-0xb6003fff: good
pci3: <network> at device 0.0 (no driver attached)
vgapci0: <VGA-compatible display> mem 0xb2000000-0xb2ffffff,0xc0000000-0xcfffffff,0xb1000000-0xb1ffffff irq 18 at device 5.0 on pci0
pci0: <memory, RAM> at device 9.0 (no driver attached)
isab0: <PCI-ISA bridge> port 0x1d00-0x1d7f at device 10.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 10.1 (no driver attached)
pci0: <processor> at device 10.3 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xb0004000-0xb0004fff irq 22 at device 11.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xb0004000
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 0 vector 49
ohci0: [MPSAFE]
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xb0005000-0xb00050ff irq 22 at device 11.1 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xb0005000
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus1: EHCI version 1.0
usbus1: <EHCI (generic) USB 2.0 controller> on ehci0
atapci0: <nVidia nForce MCP51 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3080-0x308f at device 13.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3080
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=01
ata0: stat0=0x10 err=0x01 lsb=0x14 msb=0xeb
ata0: stat1=0x01 err=0x04 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=10 stat1=01 devices=0x10000
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 50
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 51
ata1: [MPSAFE]
ata1: [ITHREAD]
atapci1: <nVidia nForce MCP51 SATA300 controller> port 0x30c0-0x30c7,0x30b4-0x30b7,0x30b8-0x30bf,0x30b0-0x30b3,0x3090-0x309f irq 23 at device 14.0 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3090
ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 52
atapci1: [MPSAFE]
atapci1: [ITHREAD]
atapci1: Lazy allocation of 0x1000 bytes rid 0x24 type 3 at 0x80000000
ata2: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x30c0
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x30b4
ata2: SATA connect time=0ms
ata2: reset tp1 mask=01 ostat0=50 ostat1=00
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x30b8
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x30b0
ata3: SATA connect status=00000000
ata3: [MPSAFE]
ata3: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pcib3: domain 0
pcib3: secondary bus 7
pcib3: subordinate bus 7
pcib3: I/O decode 0xf000-0xfff
pcib3: memory decode 0xb8000000-0xb80fffff
pcib3: no prefetched decode
pcib3: Subtractively decoded bridge.
pci7: <ACPI PCI bus> on pcib3
pci7: domain=0, physical bus=7
hdac0: <NVidia MCP51 High Definition Audio Controller> mem 0xb0000000-0xb0003fff irq 21 at device 16.1 on pci0
hdac0: HDA Driver Revision: 20090215_0128
hdac0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xb0000000
ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 0 vector 53
hdac0: [MPSAFE]
hdac0: [ITHREAD]
nfe0: <NVIDIA nForce 430 MCP13 Networking Adapter> port 0x30e0-0x30e7 mem 0xb0008000-0xb0008fff irq 20 at device 20.0 on pci0
nfe0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xb0008000
miibus0: <MII bus> on nfe0
rlphy0: <RTL8201L 10/100 media interface> PHY 1 on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
nfe0: bpf attached
nfe0: Ethernet address: 00:1b:24:68:7c:d7
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 0 vector 54
nfe0: [MPSAFE]
nfe0: [FILTER]
acpi_tz0: <Thermal Zone> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 55
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 56
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
powernow0: <PowerNow! K8> on cpu0
cpu1: <ACPI CPU> on acpi0
powernow1: <PowerNow! K8> on cpu1
ex_isa_identify()
isa_probe_children: disabling PnP devices
atkbdc: atkbdc0 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xcf800-0xd0fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at irq 7 on isa0
uart0: <ns8250> failed to probe at port 0x3f8-0x3ff irq 4 on isa0
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
uart2: not probed (disabled)
uart3: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 100458054 hz
Timecounter "TSC" frequency 1908702688 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
ata0: Identifying devices: 00010000
ata0: New devices: 00010000
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 480Mbps High Speed USB v2.0
acpi_acad0: acline initialization start
battery0: battery initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
ugen0.1: <nVidia> at usbus0
ushub0: <nVidia OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <nVidia> at usbus1
ushub1: <nVidia EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ata0-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire
acd0: setting PIO4 on nForce MCP51 chip
acd0: <TSSTcorpCD/DVDW TS-L632M/0917> DVDR drive at ata0 as master
acd0: read 4134KB/s (4134KB/s) write 172KB/s (4134KB/s), 2048KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata1: Identifying devices: 00000000
ata1: New devices: 00000000
ata2: Identifying devices: 00000001
ata2: New devices: 00000001
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ad4: 152627MB <WDC WD1600BEVS-60RST0 04.01G04> at ata2-master SATA150
ad4: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
ad4: nVidia check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ata3: Identifying devices: 00000000
ata3: New devices: 00000000
GEOM: ad4: partition 3 does not start on a track boundahdac0: Probing codec #0...
hdac0: HDA Codec #0: Conexant CX20549 (Venice)
hdac0: HDA Codec ID: 0x14f15045
hdac0: Vendor: 0x14f1
hdac0: Device: 0x5045
hdac0: Revision: 0x01
hdac0: Stepping: 0x00
hdac0: PCI Subvendor: 0x30b7103c
hdac0: Found audio FG nid=1 startnode=16 endnode=28 total=12
hdac0: Found modem FG nid=2 startnode=112 endnode=116 total=4
hdac0:
hdac0: Processing audio FG cad=0 nid=1...
hdac0: GPIO: 0x00000000 NumGPIO=0 NumGPO=0 NumGPI=0 GPIWake=0 GPIUnsol=0
hdac0: nid 16 0x95170110 as 1 seq 0 Speaker Fixed jack 7 loc 21 color Unknown misc 1
hdac0: nid 17 0x0221101f as 1 seq 15 Headphones Jack jack 1 loc 2 color Black misc 0
hdac0: nid 18 0x40a190f0 as 15 seq 0 Mic None jack 1 loc 0 color Pink misc 0
hdac0: nid 19 0x22451130 as 3 seq 0 SPDIF-out Jack jack 5 loc 34 color Black misc 1
hdac0: nid 20 0x02a79120 as 2 seq 0 Mic Jack jack 7 loc 2 color Pink misc 1
hdac0: nid 21 0x400001f0 as 15 seq 0 Line-out None jack 0 loc 0 color Unknown misc 1
hdac0: Patched pins configuration:
hdac0: nid 16 0x95170110 as 1 seq 0 Speaker Fixed jack 7 loc 21 color Unknown misc 1
hdac0: nid 17 0x0221101f as 1 seq 15 Headphones Jack jack 1 loc 2 color Black misc 0
hdac0: nid 18 0x40a190f0 as 15 seq 0 Mic None jack 1 loc 0 color Pink misc 0 [DISABLED]
hdac0: nid 19 0x22451130 as 3 seq 0 SPDIF-out Jack jack 5 loc 34 color Black misc 1
hdac0: nid 20 0x02a79120 as 2 seq 0 Mic Jack jack 7 loc 2 color Pink misc 1
hdac0: nid 21 0x400001f0 as 15 seq 0 Line-out None jack 0 loc 0 color Unknown misc 1 [DISABLED]
hdac0: 3 associations found:
hdac0: Association 0 (1) out:
hdac0: Pin nid=16 seq=0
hdac0: Pin nid=17 seq=15
hdac0: Association 1 (2) in:
hdac0: Pin nid=20 seq=0
hdac0: Association 2 (3) out:
hdac0: Pin nid=19 seq=0
hdac0: Tracing association 0 (1)
hdac0: Pin 16 traced to DAC 25
hdac0: Pin 17 traced to DAC 25 and hpredir 0
hdac0: Association 0 (1) trace succeeded
hdac0: Tracing association 1 (2)
hdac0: Pin 20 traced to ADC 26
hdac0: Association 1 (2) trace succeeded
hdac0: Tracing association 2 (3)
hdac0: Pin 19 traced to DAC 24
hdac0: Association 2 (3) trace succeeded
hdac0: Tracing input monitor
hdac0: Tracing nid 23 to out
hdac0: nid 23 is input monitor
hdac0: Tracing beeper
hdac0: Enabling headphone/speaker audio routing switching:
hdac0: as=0 sense nid=17 [UNSOL]
hdac0: Pin sense: nid=17 res=0x7fffffff
hdac0: FG config/quirks: ivref50 ivref80 ivref100 ivref
hdac0:
hdac0: +-------------------+
hdac0: | DUMPING HDA NODES |
hdac0: +-------------------+
hdac0:
hdac0: Default Parameter
hdac0: -----------------
hdac0: Stream cap: 0x00000001
hdac0: PCM
hdac0: PCM cap: 0x000e0140
hdac0: 16 20 24 bits, 48 96 KHz
hdac0: IN amp: 0x00000000
hdac0: OUT amp: 0x00000000
hdac0:
hdac0: nid: 16
hdac0: Name: pin: Speaker (Fixed)
hdac0: Widget cap: 0x0040058d
hdac0: PWR UNSOL STEREO
hdac0: Association: 0 (0x00000001)
hdac0: Pin cap: 0x00010014
hdac0: PDC OUT EAPD
hdac0: Pin config: 0x95170110
hdac0: Pin control: 0x00000040 OUT
hdac0: EAPD: 0x00000002
hdac0: Output amp: 0x80052b2b
hdac0: mute=1 step=43 size=5 offset=43
hdac0: connections: 2
hdac0: |
hdac0: + <- nid=25 [audio output] (selected)
hdac0: + [DISABLED] <- nid=23 [audio mixer]
hdac0:
hdac0: nid: 17
hdac0: Name: pin: Headphones (Black Jack)
hdac0: Widget cap: 0x0040058d
hdac0: PWR UNSOL STEREO
hdac0: Association: 0 (0x00008000)
hdac0: Pin cap: 0x0000113c
hdac0: PDC HP OUT IN VREF[ 80 HIZ ]
hdac0: Pin config: 0x0221101f
hdac0: Pin control: 0x000000c0 HP OUT
hdac0: Output amp: 0x80052b2b
hdac0: mute=1 step=43 size=5 offset=43
hdac0: connections: 2
hdac0: |
hdac0: + <- nid=25 [audio output] (selected)
hdac0: + [DISABLED] <- nid=23 [audio mixer]
hdac0:
hdac0: nid: 18 [DISABLED]
hdac0: Name: pin: Mic (None)
hdac0: Widget cap: 0x0040058d
hdac0: PWR UNSOL STEREO
hdac0: Pin cap: 0x0000113c
hdac0: PDC HP OUT IN VREF[ 80 HIZ ]
hdac0: Pin config: 0x40a190f0
hdac0: Pin control: 0x00000000
hdac0: Output amp: 0x80052b2b
hdac0: mute=1 step=43 size=5 offset=43
hdac0: connections: 2
hdac0: |
hdac0: + [DISABLED] <- nid=25 [audio output] (selected)
hdac0: + <- nid=23 [audio mixer]
hdac0:
hdac0: nid: 19
hdac0: Name: pin: SPDIF-out (Black Jack)
hdac0: Widget cap: 0x00400301
hdac0: DIGITAL STEREO
hdac0: Association: 2 (0x00000001)
hdac0: Pin cap: 0x00000010
hdac0: OUT
hdac0: Pin config: 0x22451130
hdac0: Pin control: 0x00000040 OUT
hdac0: connections: 1
hdac0: |
hdac0: + <- nid=24 [audio output]
hdac0:
hdac0: nid: 20
hdac0: Name: pin: Mic (Pink Jack)
hdac0: Widget cap: 0x00400081
hdac0: UNSOL STEREO
hdac0: Association: 1 (0x00000001)
hdac0: OSS: mic (mic)
hdac0: Pin cap: 0x00001124
hdac0: PDC IN VREF[ 80 HIZ ]
hdac0: Pin config: 0x02a79120
hdac0: Pin control: 0x00000024 IN VREFs
hdac0:
hdac0: nid: 21 [DISABLED]
hdac0: Name: pin: Line-out (None)
hdac0: Widget cap: 0x00400001
hdac0: STEREO
hdac0: Pin cap: 0x00000020
hdac0: IN
hdac0: Pin config: 0x400001f0
hdac0: Pin control: 0x00000000
hdac0:
hdac0: nid: 22
hdac0: Name: beep widget
hdac0: Widget cap: 0x0070000c
hdac0: Association: -2 (0x00000000)
hdac0: OSS: speaker (speaker)
hdac0: Output amp: 0x800b0707
hdac0: mute=1 step=7 size=11 offset=7
hdac0:
hdac0: nid: 23
hdac0: Name: audio mixer
hdac0: Widget cap: 0x0020050b
hdac0: PWR STEREO
hdac0: Association: -2 (0x00000001)
hdac0: OSS: mix (mix)
hdac0: Input amp: 0x80052b14
hdac0: mute=1 step=43 size=5 offset=20
hdac0: connections: 5
hdac0: |
hdac0: + <- nid=25 [audio output]
hdac0: + <- nid=20 [pin: Mic (Pink Jack)]
hdac0: + [DISABLED] <- nid=18 [pin: Mic (None)] [DISABLED]
hdac0: + [DISABLED] <- nid=17 [pin: Headphones (Black Jack)]
hdac0: + [DISABLED] <- nid=21 [pin: Line-out (None)] [DISABLED]
hdac0:
hdac0: nid: 24
hdac0: Name: audio output
hdac0: Widget cap: 0x00000211
hdac0: DIGITAL STEREO
hdac0: Association: 2 (0x00000001)
hdac0: OSS: pcm (pcm)
hdac0: Stream cap: 0x00000005
hdac0: AC3 PCM
hdac0: PCM cap: 0x00060040
hdac0: 16 20 bits, 48 KHz
hdac0:
hdac0: nid: 25
hdac0: Name: audio output
hdac0: Widget cap: 0x00000c11
hdac0: LRSWAP PWR STEREO
hdac0: Association: 0 (0x00008001)
hdac0: OSS: pcm (pcm)
hdac0: Stream cap: 0x00000001
hdac0: PCM
hdac0: PCM cap: 0x000e0540
hdac0: 16 20 24 bits, 48 96 192 KHz
hdac0:
hdac0: nid: 26
hdac0: Name: audio input
hdac0: Widget cap: 0x00100d0b
hdac0: LRSWAP PWR STEREO
hdac0: Association: 1 (0x00000001)
hdac0: Stream cap: 0x00000001
hdac0: PCM
hdac0: PCM cap: 0x000e0140
hdac0: 16 20 24 bits, 48 96 KHz
hdac0: Input amp: 0x80051700
hdac0: mute=1 step=23 size=5 offset=0
hdac0: connections: 5
hdac0: |
hdac0: + <- nid=23 [audio mixer] (selected)
hdac0: + <- nid=20 [pin: Mic (Pink Jack)]
hdac0: + [DISABLED] <- nid=18 [pin: Mic (None)] [DISABLED]
hdac0: + [DISABLED] <- nid=17 [pin: Headphones (Black Jack)]
hdac0: + [DISABLED] <- nid=21 [pin: Line-out (None)] [DISABLED]
hdac0:
hdac0: nid: 27 [DISABLED]
hdac0: Name: vendor widget
hdac0: Widget cap: 0x00f00000
hdac0:
hdac0: Processing modem FG cad=0 nid=2...
hdac0:
pcm0: <HDA Conexant CX20549 (Venice) PCM #0 Analog> at cad 0 nid 1 on hdac0
pcm0: +--------------------------------------+
pcm0: | DUMPING PCM Playback/Record Channels |
pcm0: +--------------------------------------+
pcm0:
pcm0: Playback:
pcm0:
pcm0: Stream cap: 0x00000001
pcm0: PCM
pcm0: PCM cap: 0x000e0540
pcm0: 16 20 24 bits, 48 96 192 KHz
pcm0: DAC: 25
pcm0:
pcm0: Record:
pcm0:
pcm0: Stream cap: 0x00000001
pcm0: PCM
pcm0: PCM cap: 0x000e0140
pcm0: 16 20 24 bits, 48 96 KHz
pcm0: ADC: 26
pcm0:
pcm0: +--------------------------------+
pcm0: | DUMPING Playback/Record Pathes |
pcm0: +--------------------------------+
pcm0:
pcm0: Playback:
pcm0:
pcm0: nid=16 [pin: Speaker (Fixed)]
pcm0: |
pcm0: + <- nid=25 [audio output] [src: pcm]
pcm0:
pcm0: nid=17 [pin: Headphones (Black Jack)]
pcm0: |
pcm0: + <- nid=25 [audio output] [src: pcm]
pcm0:
pcm0: Record:
pcm0:
pcm0: nid=26 [audio input]
pcm0: |
pcm0: + <- nid=23 [audio mixer] [src: mix]
pcm0: + <- nid=20 [pin: Mic (Pink Jack)] [src: mic]
pcm0:
pcm0: Input Mix:
pcm0:
pcm0: nid=23 [audio mixer]
pcm0: |
pcm0: + <- nid=25 [audio output] [src: pcm]
pcm0: + <- nid=20 [pin: Mic (Pink Jack)] [src: mic]
pcm0:
pcm0: +-------------------------+
pcm0: | DUMPING Volume Controls |
pcm0: +-------------------------+
pcm0:
pcm0: Master Volume (OSS: vol)
pcm0: |
pcm0: +- ctl 1 (nid 16 in ): -64/0dB (44 steps) + mute
pcm0: +- ctl 2 (nid 17 in ): -64/0dB (44 steps) + mute
pcm0:
pcm0: PCM Volume (OSS: pcm)
pcm0: |
pcm0: +- ctl 1 (nid 16 in ): -64/0dB (44 steps) + mute
pcm0: +- ctl 2 (nid 17 in ): -64/0dB (44 steps) + mute
pcm0: +- ctl 5 (nid 23 in 0): -30/34dB (44 steps) + mute
pcm0:
pcm0: Microphone Volume (OSS: mic)
pcm0: |
pcm0: +- ctl 6 (nid 23 in 1): -30/34dB (44 steps) + mute
pcm0:
pcm0: Speaker/Beep Volume (OSS: speaker)
pcm0: |
pcm0: +- ctl 4 (nid 22 out): -21/0dB (8 steps) + mute
pcm0:
pcm0: Recording Level (OSS: rec)
pcm0: |
pcm0: +- ctl 10 (nid 26 in 0): 0/34dB (24 steps) + mute
pcm0:
pcm0: Input Mix Level (OSS: mix)
pcm0: |
pcm0: +- ctl 10 (nid 26 in 0): 0/34dB (24 steps) + mute
pcm0:
pcm0: Mixer "vol":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "mic":
pcm0: Mixer "mix":
pcm0: Mixer "rec":
pcm0: Mixer "ogain":
pcm0: clone manager: deadline=750ms flags=0x8000001e
pcm0: sndbuf_setmap 1170000, 4000; 0xfffffffe6c124000 -> 1170000
pcm0: sndbuf_setmap 2710000, 4000; 0xfffffffe6c134000 -> 2710000
pcm1: <HDA Conexant CX20549 (Venice) PCM #1 Digital> at cad 0 nid 1 on hdac0
pcm1: +--------------------------------------+
pcm1: | DUMPING PCM Playback/Record Channels |
pcm1: +--------------------------------------+
pcm1:
pcm1: Playback:
pcm1:
pcm1: Stream cap: 0x00000005
pcm1: AC3 PCM
pcm1: PCM cap: 0x00060040
pcm1: 16 20 bits, 48 KHz
pcm1: DAC: 24
pcm1:
pcm1: +--------------------------------+
pcm1: | DUMPING Playback/Record Pathes |
pcm1: +--------------------------------+
pcm1:
pcm1: Playback:
pcm1:
pcm1: nid=19 [pin: SPDIF-out (Black Jack)]
pcm1: |
pcm1: + <- nid=24 [audio output] [src: pcm]
pcm1:
pcm1: +-------------------------+
pcm1: | DUMPING Volume Controls |
pcm1: +-------------------------+
pcm1:
pcm1: clone manager: deadline=750ms flags=0x8000001e
pcm1: sndbuf_setmap 2730000, 4000; 0xfffffffe6c144000 -> 2730000
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00000400
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 1 vector 48
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 1 vector 49
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 1 vector 50
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 1 vector 51
WARNING: WITNESS option enabled, expect reduced performance.
ry.
GEOM: ad4: partition 3 does not end on a track boundary.
GEOM: ad4: partition 1 does not end on a track boundary.
battery0: battery initialization done, tried 1 times
GEOM_LABEL: Label for provider ad4s2 is ntfs/HP_RECOVERY.
GEOM: ad4s4: geometry does not match label (255h,63s != 16h,63s).
ushub0: 8 ports with 8 removable, self powered
GEOM_CONCAT: Device export created (id=3382027346).
GEOM_CONCAT: Disk ad4s3f attached to export.
GEOM_CONCAT: Disk ad4s4f attached to export.
GEOM_CONCAT: Device export activated.
Root mount waiting for: usbus1
Root mount waiting for: usbus1
Root mount waiting for: usbus1
ushub1: 8 ports with 8 removable, self powered
Root mount waiting for: usbus1
Root mount waiting for: usbus1
ugen0.2: <NEC> at usbus0
ushub2: <NEC hub, class 9/0, rev 1.00/1.00, addr 2> on usbus0
ugen1.2: <Sonix Technology Co., Ltd.> at usbus1
Trying to mount root from ufs:/dev/ad4s3a
ct_to_ts([2009-02-25 21:06:49]) = 1235596009.000000000
start_init: trying /sbin/init
ushub2: 4 ports with 4 removable, bus powered
ugen0.3: <Alps Electric> at usbus0
ukbd0: <Alps Electric M2452, class 0/0, rev 1.00/1.01, addr 3> on usbus0
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
crypto: <crypto core>
cryptosoft0: <software crypto> on motherboard
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
ugen0.4: <Creative Labs> at usbus0
ums0: <Creative Labs product 0x0003, class 0/0, rev 1.10/0.00, addr 4> on usbus0
ums0: 3 buttons and [XYZ] coordinates
Symlink: ums0 -> usb0.4.0.16
GEOM_ELI: Device concat/export.eli created.
GEOM_ELI: Encryption: AES-CBC 128
GEOM_ELI: Crypto: software
GEOM_JOURNAL: Journal 578595679: concat/export.eli contains data.
GEOM_JOURNAL: Journal 578595679: ad4s4g contains journal.
GEOM_JOURNAL: Journal concat/export.eli clean.
WARNING: TMPFS is considered to be a highly experimental feature in FreeBSD.
WARNING: TMPFS is considered to be a highly experimental feature in FreeBSD.
md0.uzip: 16384 x 65536 blocks
module_register: module ushub/ums already exists!
Module ushub/ums failed to register: 17
lock order reversal:
1st 0xfffffffe5db783f8 bufwait (bufwait) @ /usr/src/head/sys/kern/vfs_bio.c:2443
2nd 0xffffff0002d25a00 dirhash (dirhash) @ /usr/src/head/sys/ufs/ufs/ufs_dirhash.c:275
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2a
_witness_debugger() at _witness_debugger+0x2e
witness_checkorder() at witness_checkorder+0x81e
_sx_xlock() at _sx_xlock+0x55
ufsdirhash_acquire() at ufsdirhash_acquire+0x33
ufsdirhash_add() at ufsdirhash_add+0x19
ufs_direnter() at ufs_direnter+0x88b
ufs_makeinode() at ufs_makeinode+0x338
VOP_CREATE_APV() at VOP_CREATE_APV+0x8d
null_bypass() at null_bypass+0xd3
VOP_CREATE_APV() at VOP_CREATE_APV+0xa6
vn_open_cred() at vn_open_cred+0x479
kern_openat() at kern_openat+0x169
syscall() at syscall+0x1dd
Xfast_syscall() at Xfast_syscall+0xab
--- syscall (5, FreeBSD ELF64, open), rip = 0x80c39fdc, rsp = 0x7fffffffe1f8, rbp = 0xa ---
pid 1110 (luit) is using legacy pty devices
pid 1113 (luit) is using legacy pty devices
pid 1111 (luit) is using legacy pty devices
pid 1112 (luit) is using legacy pty devices
pid 1114 (luit) is using legacy pty devices
pid 1088 (xosview), uid 1000: exited on signal 11
-------------- next part --------------
none0 at pci0:0:0:0: class=0x050000 card=0x30b7103c chip=0x02f010de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Host Bridge'
class = memory
subclass = RAM
cap 08[44] = HT slave
cap 08[e0] = HT MSI address window disabled at 0xfee00000
none1 at pci0:0:0:1: class=0x050000 card=0x30b7103c chip=0x02fa10de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Memory Controller 0'
class = memory
subclass = RAM
none2 at pci0:0:0:2: class=0x050000 card=0x30b7103c chip=0x02fe10de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Memory Controller 1'
class = memory
subclass = RAM
none3 at pci0:0:0:3: class=0x050000 card=0x30b7103c chip=0x02f810de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Memory Controller 5'
class = memory
subclass = RAM
none4 at pci0:0:0:4: class=0x050000 card=0x30b7103c chip=0x02f910de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Memory Controller 4'
class = memory
subclass = RAM
none5 at pci0:0:0:5: class=0x050000 card=0x30b7103c chip=0x02ff10de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Host Bridge'
class = memory
subclass = RAM
cap 00[44] = unknown
cap 00[fe] = unknown
none6 at pci0:0:0:6: class=0x050000 card=0x30b7103c chip=0x027f10de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Memory Controller 3'
class = memory
subclass = RAM
none7 at pci0:0:0:7: class=0x050000 card=0x00000000 chip=0x027e10de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 Memory Controller 2'
class = memory
subclass = RAM
pcib1 at pci0:0:2:0: class=0x060400 card=0x000010de chip=0x02fc10de rev=0xa1 hdr=0x01
vendor = 'Nvidia Corp'
device = 'C51 PCIe Bridge'
class = bridge
subclass = PCI-PCI
cap 0d[40] = PCI Bridge card=0x000010de
cap 01[48] = powerspec 2 supports D0 D3 current D0
cap 05[50] = MSI supports 2 messages, 64 bit
cap 08[60] = HT MSI address window disabled at 0xfee00000
cap 10[80] = PCI-Express 1 root port
pcib2 at pci0:0:3:0: class=0x060400 card=0x000010de chip=0x02fd10de rev=0xa1 hdr=0x01
vendor = 'Nvidia Corp'
device = 'C51 PCIe Bridge'
class = bridge
subclass = PCI-PCI
cap 0d[40] = PCI Bridge card=0x000010de
cap 01[48] = powerspec 2 supports D0 D3 current D0
cap 05[50] = MSI supports 2 messages, 64 bit
cap 08[60] = HT MSI address window disabled at 0xfee00000
cap 10[80] = PCI-Express 1 root port
vgapci0 at pci0:0:5:0: class=0x030000 card=0x30b7103c chip=0x024410de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'C51 PCIe Bridge'
class = display
subclass = VGA
cap 01[48] = powerspec 2 supports D0 D3 current D0
cap 05[50] = MSI supports 1 message, 64 bit
none8 at pci0:0:9:0: class=0x050000 card=0x30b7103c chip=0x027010de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 Host Bridge'
class = memory
subclass = RAM
cap 08[44] = HT slave
cap 08[e0] = HT MSI address window enabled at 0xfee00000
isab0 at pci0:0:10:0: class=0x060100 card=0x30b7103c chip=0x026010de rev=0xa3 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 LPC Bridge'
class = bridge
subclass = PCI-ISA
none9 at pci0:0:10:1: class=0x0c0500 card=0x30b7103c chip=0x026410de rev=0xa3 hdr=0x00
vendor = 'Nvidia Corp'
device = 'NVIDIA SMB Bus Controller NVIDIA nForce PCI System Management'
class = serial bus
subclass = SMBus
cap 01[44] = powerspec 2 supports D0 D3 current D0
none10 at pci0:0:10:3: class=0x0b4000 card=0x30b7103c chip=0x027110de rev=0xa3 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 PMU'
class = processor
ohci0 at pci0:0:11:0: class=0x0c0310 card=0x30b7103c chip=0x026d10de rev=0xa3 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 USB Controller'
class = serial bus
subclass = USB
cap 01[44] = powerspec 2 supports D0 D1 D2 D3 current D0
ehci0 at pci0:0:11:1: class=0x0c0320 card=0x30b7103c chip=0x026e10de rev=0xa3 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 USB Controller'
class = serial bus
subclass = USB
cap 0a[44] = EHCI Debug Port at offset 0x98 in map 0x14
cap 01[80] = powerspec 2 supports D0 D1 D2 D3 current D0
atapci0 at pci0:0:13:0: class=0x01018a card=0x30b7103c chip=0x026510de rev=0xf1 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 Parallel ATA Controller'
class = mass storage
subclass = ATA
cap 01[44] = powerspec 2 supports D0 D3 current D0
atapci1 at pci0:0:14:0: class=0x010185 card=0x30b7103c chip=0x026610de rev=0xf1 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 Serial ATA Controller'
class = mass storage
subclass = ATA
cap 01[44] = powerspec 2 supports D0 D3 current D0
cap 05[b0] = MSI supports 4 messages, 64 bit
cap 08[cc] = HT MSI fixed address window disabled at 0xfee00000
pcib3 at pci0:0:16:0: class=0x060401 card=0x00000000 chip=0x026f10de rev=0xa2 hdr=0x01
vendor = 'Nvidia Corp'
device = 'MCP51 PCI Bridge'
class = bridge
subclass = PCI-PCI
cap 0d[b8] = PCI Bridge card=0x00000000
cap 08[8c] = HT MSI address window disabled at 0xfee00000
hdac0 at pci0:0:16:1: class=0x040300 card=0x30b7103c chip=0x026c10de rev=0xa2 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 High Definition Audio'
class = multimedia
subclass = HDA
cap 01[44] = powerspec 2 supports D0 D3 current D0
cap 05[50] = MSI supports 1 message, 64 bit, vector masks
cap 08[6c] = HT MSI fixed address window disabled at 0xfee00000
nfe0 at pci0:0:20:0: class=0x068000 card=0x30b7103c chip=0x026910de rev=0xa3 hdr=0x00
vendor = 'Nvidia Corp'
device = 'MCP51 Network Bus Enumerator'
class = bridge
cap 01[44] = powerspec 2 supports D0 D1 D2 D3 current D0
hostb0 at pci0:0:24:0: class=0x060000 card=0x00000000 chip=0x11001022 rev=0x00 hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = '(K8) Athlon 64/Opteron HyperTransport Technology Configuration'
class = bridge
subclass = HOST-PCI
cap 08[80] = HT host
hostb1 at pci0:0:24:1: class=0x060000 card=0x00000000 chip=0x11011022 rev=0x00 hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = '(K8) Athlon 64/Opteron Address Map'
class = bridge
subclass = HOST-PCI
hostb2 at pci0:0:24:2: class=0x060000 card=0x00000000 chip=0x11021022 rev=0x00 hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = '(K8) Athlon 64/Opteron DRAM Controller'
class = bridge
subclass = HOST-PCI
hostb3 at pci0:0:24:3: class=0x060000 card=0x00000000 chip=0x11031022 rev=0x00 hdr=0x00
vendor = 'Advanced Micro Devices (AMD)'
device = '(K8) Athlon 64/Opteron Miscellaneous Control'
class = bridge
subclass = HOST-PCI
cap 0f[f0] = unknown
none11 at pci0:3:0:0: class=0x028000 card=0x1374103c chip=0x431114e4 rev=0x02 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'Dell Wireless 1390 WLAN Mini-PCI Card'
class = network
cap 01[40] = powerspec 3 supports D0 D1 D2 D3 current D0
cap 09[58] = vendor (length 120)
cap 05[e8] = MSI supports 1 message, 64 bit
cap 10[d0] = PCI-Express 1 endpoint
More information about the freebsd-current
mailing list