lpt stopped working
Christian Gusenbauer
c47g at gmx.at
Tue Feb 10 12:51:27 PST 2009
On Tuesday 10 February 2009, Alexey Shuvaev wrote:
> On Mon, Feb 09, 2009 at 02:58:41PM -0500, John Baldwin wrote:
> > On Monday 09 February 2009 1:58:39 pm Christian Gusenbauer wrote:
> > > On Monday 09 February 2009, John Baldwin wrote:
> > > > Please help to debug this so we can have working lpt0 in 8.0. No one
> > > > tested the patches months ago when I first posted them, and if folks
> > > > do
> >
> > not
> >
> > > > test them now I will simply remove the driver before 8.0 ships. I no
> > >
> > > Mea culpa, too. As you sent your patches, I thought someone else will
> > > do the tests surely ... :-(.
> > >
> > > > longer have any hardware such that I can test this directly, so I am
> > > > depending on folks to test things I have asked for and report back.
> > > > I believe the last thing I asked for was for someone to do this when
> > > > they
> >
> > lpt
> >
> > > > was hung:
> > > >
> > > > Ok, can you run kgdb against your running kernel (Just run 'kgdb'
> > > > without any arguments) and do the following:
> > > >
> > > > (kgdb) p *(struct ppb_data *)ppbus_devclass->devices[0]->softc
> > > >
> > > > Assuming the ppb_owner is not 0, can you then do this:
> > > >
> > > > (kgdb) p *(device_t)((struct ppb_data
> > > > *)ppbus_devclass->devices[0]->softc)->ppb_owner
> > >
> > > This is the output (unfortunately ppb_owner IS 0):
> > >
> > > (kgdb) p *(struct ppb_data *)ppbus_devclass->devices[0]->softc
> > > $1 = {class_id = 10, state = 1, error = 0, mode = 0, ppb_owner = 0x0,
> > > ppc_lock = 0xc56bfe7c, ppc_irq_res = 0xc573d5c0}
> >
> > And this is while lpd or the like is hung trying to write to /dev/lpt0?
>
> Hello all!
>
> Ok, here we go. 1st, the system:
> ~> uname -a
> FreeBSD wep4035 8.0-CURRENT FreeBSD 8.0-CURRENT #0: Sat Feb 7 20:25:10 CET
> 2009 root at wep4035:/usr/obj/usr/src/sys/NOUSB amd64
>
> Parallel port (from dmesg):
> ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/9 bytes threshold
> ppc0: [ITHREAD]
> ppbus0: <Parallel port bus> on ppc0
> ppbus0: IEEE1284 device found /NIBBLE/ECP
> ppbus0: Probing for PnP devices:
> ppbus0: <HEWLETT-PACKARD OFFICEJET R60> PRINTER MLC,PCL,PML,SCL
> plip0: <PLIP network interface> on ppbus0
> plip0: [ITHREAD]
> lpt0: <Printer> on ppbus0
> lpt0: [ITHREAD]
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
>
> I have simplified things and do not run lpd. The command is:
> 'ktrace -id cat monitor_info > /dev/lpt0'
> (I think it should work?)
> kdump -E > ktrace.dump does not show anything interesting:
> [snip]
> 1564 cat 0.001120 CALL open(0x7fffffffee1c,O_RDONLY,<unused>0x6d)
> 1564 cat 0.001127 NAMI "monitor_info"
> 1564 cat 0.001143 RET open 3
> 1564 cat 0.001149 CALL fstat(0x1,0x7fffffffeac0)
> 1564 cat 0.001155 STRU struct stat {dev=83951360, ino=53,
> mode=crw-rw--- - , nlink=1, uid=0, gid=0, rdev=53,
> atime=1234294743.332164000, stime=1234294743 .332164000, ctime=1234294974,
> birthtime=-1, size=0, blksize=4096, blocks=0, flag s=0x0 }
> 1564 cat 0.001160 RET fstat 0
> 1564 cat 0.001180 CALL
> __sysctl(0x7fffffffea20,0x2,0x80085eeb8,0x7ffffff fea18,0,0)
> 1564 cat 0.001187 RET __sysctl 0
> 1564 cat 0.001191 CALL
> __sysctl(0x7fffffffea60,0x2,0x7fffffffea7c,0x7fff ffffea70,0,0)
> 1564 cat 0.001198 RET __sysctl 0
> 1564 cat 0.001203 CALL
> __sysctl(0x7fffffffea60,0x2,0x7fffffffea7c,0x7fffffffea70,0,0) 1564 cat
> 0.001208 RET __sysctl 0
> 1564 cat 0.001230 CALL
> __sysctl(0x7fffffffe5f0,0x2,0x8008509e8,0x7fffffffe5e8,0,0) 1564 cat
> 0.001236 RET __sysctl 0
> 1564 cat 0.001242 CALL readlink(0x800722639,0x7fffffffe610,0x400)
> 1564 cat 0.001248 NAMI "/etc/malloc.conf"
> 1564 cat 0.001264 RET readlink -1 errno 2 No such file or
> directory 1564 cat 0.001270 CALL issetugid
> 1564 cat 0.001275 RET issetugid 0
> 1564 cat 0.001296 CALL break(0x600000)
> 1564 cat 0.001302 RET break 0
> 1564 cat 0.001317 CALL
> __sysctl(0x7fffffffe850,0x2,0x7fffffffe86c,0x7fffffffe860,0,0) 1564 cat
> 0.001324 RET __sysctl 0
> 1564 cat 0.001329 CALL
> mmap(0,0x100000,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,0xffffffff,0)
> 1564 cat 0.001335 RET mmap 8790016/0x800862000
> 1564 cat 0.001340 CALL
> mmap(0x800962000,0x9e000,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,0xffffff
>ff,0) 1564 cat 0.001346 RET mmap 9838592/0x800962000
> 1564 cat 0.001351 CALL munmap(0x800862000,0x9e000)
> 1564 cat 0.001359 RET munmap 0
> 1564 cat 0.001378 CALL read(0x3,0x800902000,0x1000)
> 1564 cat 0.006845 GIO fd 3 read 4096 bytes
> "(II) VESA(0): VESA VBE DDC supported
> (II) VESA(0): VESA VBE DDC Level 2
> (II) VESA(0): VESA VBE DDC transfer in appr. 1 sec.
> (==) VESA(0): Write-combining range (0x0,0x1000) was already clear
> (==) VESA(0): Write-combining range (0x0,0x1000) was already clear
> [snip]
> 1 604 625 +hsync +vsync (46.9 kHz)
> (II) VESA(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
> 63\ 7 643 666 +hsync +vsync (48.1 kHz)
> (II) VESA(0): Modeline "1280x1024"x60.0 108.88 1280 1360 1496
> 1712 \ 1024 1025 1028 1060 -hsync +vsync (63.6 kHz)
> (II) VESA(0): Modeline "1680x1050"x60.0 147.14 16"
> 1564 cat 0.006879 RET read 4096/0x1000
> 1564 cat 0.006888 CALL write(0x1,0x800902000,0x1000)
> 1564 cat 114.695563 RET write RESTART
> 1564 cat 114.695637 PSIG SIGINT SIG_DFL
>
> After 114 seconds I have hit Ctrl-C.
>
> And this is from kgdb:
> (kgdb) p *(struct ppb_data *)ppbus_devclass->devices[0]->softc
> $1 = {class_id = 0, state = 1, error = 0, mode = 0,
> ppb_owner = 0xffffff0004668700, ppc_lock = 0xffffff0004668eb8,
> ppc_irq_res = 0xffffff0004677900}
> (kgdb) p *(device_t)((struct
> ppb_data*)ppbus_devclass->devices[0]->softc)->ppb _owner
> $2 = {ops = 0xffffff0001520000, link = {tqe_next = 0xffffff0004668500,
> tqe_prev = 0xffffff0004668908}, devlink = {tqe_next =
> 0xffffff0004668500, tqe_prev = 0xffffff0004668918}, parent =
> 0xffffff0004669000, children = { tqh_first = 0x0, tqh_last =
> 0xffffff0004668730},
> driver = 0xffffffff806961c0, devclass = 0xffffff00014f4900, unit = 0,
> nameunit = 0xffffff0004666940 "lpt0", desc = 0xffffffff804fc110
> "Printer", busy = 0, state = DS_ATTACHED, devflags = 0, flags = 7, order =
> 0 '\0', pad = 0 '\0', ivars = 0xffffff0004668800, softc =
> 0xffffff0004668400, sysctl_ctx = {tqh_first = 0xffffff0004674180,
> tqh_last = 0xffffff0004674288}, sysctl_tree = 0xffffff000467d480}
> (kgdb)
>
> The driver stays in this state even after exit of 'cat' process
> (I think this was already reported):
> ~> cat monitor_info > /dev/lpt0
> /dev/lpt0: Device busy.
>
> I can play with the printer et. al. (ppi, maybe plip) in the evenings,
> so if you need something else...
>
> Alexey.
> _______________________________________________
> freebsd-current at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe at freebsd.org"
I second that. I do not use lpd, too. Just a plain cat as Alexey does.
@John: sorry, it seems that I still do not get your mails :-(.
Christian.
More information about the freebsd-current
mailing list