Call for testers: re(4) and
RTL8168C/RTL8168CP/RTL8111C/RTL8111CP
Pyun YongHyeon
pyunyh at gmail.com
Sun Jun 8 01:47:28 UTC 2008
On Sat, Jun 07, 2008 at 03:52:15PM +0900, Norikatsu Shigemura wrote:
> On Sat, 7 Jun 2008 12:59:11 +0900
> Pyun YongHyeon <pyunyh at gmail.com> wrote:
> > I don't have any of these hardwares so if you have one of these
> > hardwares please give it try and let me know how it goes. Some
> > users reported success but I'd like to get more feedback because
> > re(4) supports too many variants and I don't like to break supports
> > for old RealTek hardwares.
>
> Wow!! Quite Good Works my RTL8169SBL (cardbus). I confirmed
> following operations:
>
> (ok) probe&attach
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3100-0x31ff mem 0xb0103000-0xb01031ff irq 22 at device 0.0 on cardbus0
> re0: Chip rev. 0x10000000
> re0: MAC rev. 0x00000000
> miibus1: <MII bus> on re0
> rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
> rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
> re0: Ethernet address: 00:e0:4c:77:ab:e8
> re0: [FILTER]
> re0: link state changed to DOWN
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
> (ok) ifconfig re0 (w/o cable disconnect)
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> re0: flags=8843<BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
> options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
> ether 00:e0:4c:77:ab:e8
> media: Ethernet autoselect (none)
> status: no carrier
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
> (ok) cable connected
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> re0: link state changed to UP
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
> (ok) dhclient re0
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
> options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
> ether 00:e0:4c:77:ab:e8
> inet 192.168.XXX.XXX netmask 0xffffff00 broadcast 192.168.XXX.255
> media: Ethernet autoselect (100baseTX <full-duplex>)
> status: active
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
> (ok) plug&pray
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> rgephy0: detached
> miibus1: detached
> re0: detached
> cardbus0: Expecting link target, got 0x0
> re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3100-0x31ff mem 0xb0103000-0xb01031ff irq 22 at device 0.0 on cardbus0
> re0: Chip rev. 0x10000000
> re0: MAC rev. 0x00000000
> miibus1: <MII bus> on re0
> rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
> rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
> re0: Ethernet address: 00:e0:4c:77:ab:e8
> re0: [FILTER]
> re0: link state changed to DOWN
> re0: link state changed to UP
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
> Of course, no panic!! Thank you!!
Thanks for reporting.
--
Regards,
Pyun YongHyeon
More information about the freebsd-current
mailing list