GigaByte GA-MA69VM USB+mouse problem [WAS: AMD690G/V issues with 7-current (sata, usb)]

[Michal Varga]

On Sun, 2007-10-14 at 12:58 +0200, Hans Petter Selasky wrote:
> Michal Varga:
> 
> If you run "usbdevs -v" does it show your mouse ?
> 
> --HPS

Right after boot, not:

dmesg:
uhub0: device problem (TIMEOUT), disabling port 2

usbdevs -v:
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb2:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb3:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb4:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb5:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
 port 3 powered
 port 4 powered
 port 5 powered
 port 6 powered
 port 7 powered
 port 8 powered
 port 9 powered
 port 10 powered


After that, when I replug it to another port, everything works fine:

dmesg:
ums0: <A4Tech USB Optical Mouse, class 0/0, rev 1.10/0.01, addr 2> on
uhub1
ums0: 7 buttons and Z dir.

usbdevs -v:
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 addr 2: low speed, power 100 mA, config 1, USB Optical
Mouse(0x0006), A4Tech(0x09da), rev 0.01
Controller /dev/usb2:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb3:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb4:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb5:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
ATI(0x0000), rev 1.00
 port 1 powered
 port 2 powered
 port 3 powered
 port 4 powered
 port 5 powered
 port 6 powered
 port 7 powered
 port 8 powered
 port 9 powered
 port 10 powered


m.