CURRENT from 04/01/07 + bge NIC panic
Dominic Marks
dom at helenmarks.co.uk
Mon Jan 8 17:49:27 UTC 2007
Hello,
I have a PowerEdge SC440 which panics when I set an IP to its
bge interface. I have serial console and it is sitting a ddb
prompt.
This is plain CURRENT, I made my own snapshot hence the uname.
I had a look at cvsweb but didn't see any commits to bge in
since this source.
# uname -a
FreeBSD 7.0-SNAPSHOT-20060104 FreeBSD 7.0-SNAPSHOT-20060104
#0: Thu Jan 4 20:43:26 UTC 2007 root at turtle.internal.graphdata.co.uk:/usr/obj/usr/src/sys/GENERIC i386
# cat /var/run/dmesg.boot
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
1993, 1994 The Regents of the University of California. All
rights reserved. FreeBSD is a registered trademark of The
FreeBSD Foundation. FreeBSD 7.0-SNAPSHOT-20060104 #0: Thu Jan
4 20:43:26 UTC 2007
root at turtle.internal.graphdata.co.uk:/usr/obj/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel
(R) Celeron(R) CPU 2.80GHz (2793.09-MHz 686-class CPU) Origin =
"GenuineIntel" Id = 0xf49 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x651d<SSE3,RSVD2,MON,DS_CPL,TM2,CNTX-ID,CX16,XTPR>
AMD Features=0x20100000<NX,LM> AMD Features2=0x1<LAHF>
real memory = 535281664 (510 MB)
avail memory = 510054400 (486 MB)
ACPI APIC Table: <DELL B8K >
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112,
RF2413, RF5413) acpi0: <DELL B8K > on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on
acpi0 cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci4: <ACPI PCI bus> on pcib4
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC
rev. 0xb002> mem 0xefcf0000-0xefcfffff irq 17 at device 0.0 on
pci4 miibus0: <MII bus> on bge0 ukphy0: <Generic IEEE 802.3u
media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX,
100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto bge0:
Ethernet address: 00:13:72:35:f5:d0 uhci0: <UHCI (generic) USB
controller> port 0xff80-0xff9f irq 21 at device 29.0 on pci0 uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1>
on usb0 uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xff60-0xff7f irq
22 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1>
on usb1 uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xff40-0xff5f irq
18 at device 29.2 on pci0 uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1>
on usb2 uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0xff20-0xff3f irq
23 at device 29.3 on pci0 uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1>
on usb3 uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem
0xff980800-0xff980bff irq 21 at device 29.7 on pci0 ehci0:
[GIANT-LOCKED] usb4: waiting for BIOS to give up control
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1>
on usb4 uhub4: 8 ports with 8 removable, self powered
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
vgapci0: <VGA-compatible display> port 0xdc00-0xdcff mem
0xe0000000-0xe7ffffff,0xefaf0000-0xefafffff irq 19 at device
7.0 on pci5 isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100
controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 16 at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH7 SATA300 controller> port
0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfecf
mem 0xeffffc00-0xefffffff irq 20 at device 31.2 on pci0 ata2:
<ATA channel 0> on atapci1 ata3: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags
0x10 on acpi0 sio0: type 16550A, console sio0: [FAST]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc8fff,0xc9000-0xcafff,0xcb000-0xcbfff pnpid ORM0000
on isa0 atkbdc0: <Keyboard controller (i8042)> at port
0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0
at atkbd0 atkbd0: [GIANT-LOCKED]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0 ukbd0: <CHICONY Compaq USB Keyboard,
class 0/0, rev 1.10/1.05, addr 2> on uhub3 kbd2 at ukbd0
uhid0: <CHICONY Compaq USB Keyboard, class 0/0, rev 1.10/1.05,
addr 2> on uhub3 Timecounter "TSC" frequency 2793085123 Hz
quality 800 Timecounters tick every 1.000 msec
acd0: CDROM <LTN486S/YQSM> at ata0-master PIO4
ad4: 238418MB <WDC WD2500JS-75NCB3 10.02E04> at ata2-master
SATA150 Trying to mount root from ufs:/dev/ad4s1a
WARNING: /var was not properly dismounted
WARNING: /var/log was not properly dismounted
# pciconf -lv
hostb0 at pci0:0:0: class=0x060000 card=0x01df1028
chip=0x27788086 rev=0x00 hdr=0x00 vendor = 'Intel Corporation'
device = 'E7230/3000/3010 Processor to I/O Controller'
class = bridge
subclass = HOST-PCI
pcib1 at pci0:1:0: class=0x060400 card=0x00000088 chip=0x27798086
rev=0x00 hdr=0x01 vendor = 'Intel Corporation'
device = 'E7230/3000/3010 PCI Express Root Port'
class = bridge
subclass = PCI-PCI
pcib2 at pci0:28:0: class=0x060400 card=0x00000040
chip=0x27d08086 rev=0x01 hdr=0x01 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) PCI Express Root Port'
class = bridge
subclass = PCI-PCI
pcib3 at pci0:28:4: class=0x060400 card=0x00000040
chip=0x27e08086 rev=0x01 hdr=0x01 vendor = 'Intel Corporation'
device = '82801GR/GH/GHM (ICH7 Family) PCI Express Root
Port' class = bridge
subclass = PCI-PCI
pcib4 at pci0:28:5: class=0x060400 card=0x00000040
chip=0x27e28086 rev=0x01 hdr=0x01 vendor = 'Intel Corporation'
device = '82801GR/GH/GHM (ICH7 Family) PCI Express Root
Port' class = bridge
subclass = PCI-PCI
uhci0 at pci0:29:0: class=0x0c0300 card=0x01df1028
chip=0x27c88086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host
Controller' class = serial bus
subclass = USB
uhci1 at pci0:29:1: class=0x0c0300 card=0x01df1028
chip=0x27c98086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host
Controller' class = serial bus
subclass = USB
uhci2 at pci0:29:2: class=0x0c0300 card=0x01df1028
chip=0x27ca8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host
Controller' class = serial bus
subclass = USB
uhci3 at pci0:29:3: class=0x0c0300 card=0x01df1028
chip=0x27cb8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host
Controller' class = serial bus
subclass = USB
ehci0 at pci0:29:7: class=0x0c0320 card=0x01df1028
chip=0x27cc8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB 2.0 Enhanced Host
Controller' class = serial bus
subclass = USB
pcib5 at pci0:30:0: class=0x060401 card=0x00000050
chip=0x244e8086 rev=0xe1 hdr=0x01 vendor = 'Intel Corporation'
device = '82801BA/CA/DB/DBL/EB/ER/FB/GB/HB
(ICH2/3/4/4/5/5/6/7/8), 63xxESB Hub Interface to PCI Bridge'
class = bridge subclass = PCI-PCI
isab0 at pci0:31:0: class=0x060100 card=0x00000000
chip=0x27b88086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801GB/GR (ICH7 Family) LPC Interface
Controller' class = bridge
subclass = PCI-ISA
atapci0 at pci0:31:1: class=0x01018a card=0x01df1028
chip=0x27df8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) Ultra ATA Storage
Controller' class = mass storage
subclass = ATA
atapci1 at pci0:31:2: class=0x01018f card=0x01df1028
chip=0x27c08086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801GB/GR/GH (ICH7 Family) Serial ATA Storage
Controller' class = mass storage
subclass = ATA
none0 at pci0:31:3: class=0x0c0500 card=0x01df1028
chip=0x27da8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) SMBus Controller'
class = serial bus
subclass = SMBus
bge0 at pci4:0:0: class=0x020000 card=0x01df1028 chip=0x167a14e4
rev=0x02 hdr=0x00 vendor = 'Broadcom Corporation'
device = 'NetXtreme BCM5754 Gigabit Ethernet PCI Express'
class = network
subclass = ethernet
vgapci0 at pci5:7:0: class=0x030000 card=0x01df1028
chip=0x515e1002 rev=0x02 hdr=0x00 vendor = 'ATI Technologies
Inc.' device = 'Radeon ES1000 Radeon ES1000'
class = display
subclass = VGA
To trigger the panic:
# dhclient bge0
panic: invalid ife->ifm_data (0xa) in mii_phy_setmedia
cpuid = 0
KDB: enter: panic
[thread pid 650 tid 100063 ]
Stopped at kdb_enter+0x2b: nop
db> where
Tracing pid 650 tid 100063 td 0xc30ead80
kdb_enter(c094055e) at kdb_enter+0x2b
panic(c092025d,a,d0391b4b,c2,ce8eea68,...) at panic+0x11c
mii_phy_setmedia(c2e74580) at mii_phy_setmedia+0x83
ukphy_service(c2e74580,c2e74e40,2) at ukphy_service+0xfd
mii_mediachg(c2e74e40,8803,c2e74e40,c2e6c800,c2e76000,...) at
mii_mediachg+0x27 bge_stop
(c2e76000,80206910,c30d0000,c2e76000,d60e6b80,...) at bge_stop
+0x58b bge_init_locked(c2e76000) at bge_init_locked+0x36
bge_ioctl(c2e6c800,80206910,c30d0000) at bge_ioctl+0x136
ifhwioctl(80206910,c2e6c800,c30d0000,c30ead80) at ifhwioctl
+0x3b2 ifioctl(c30de530,80206910,c30d0000,c30ead80,0,...) at
ifioctl+0x101 soo_ioctl
(c3010a20,80206910,c30d0000,c31fea00,c30ead80) at soo_ioctl
+0x2db kern_ioctl(c30ead80,3,80206910,c30d0000) at kern_ioctl
+0x296 ioctl(c30ead80,d60e6d00) at ioctl+0xf1 syscall(d60e6d38)
at syscall+0x256 Xint0x80_syscall() at Xint0x80_syscall+0x20
--- syscall (0, FreeBSD ELF32, nosys), eip = 0x2, esp = 0x247,
ebp = 0x1 ---
The panic comes from this KASSERT in mii_physubr.c
KASSERT(ife->ifm_data >=0 && ife->ifm_data < MII_NMEDIA,
("invalid ife->ifm_data (0x%x) in mii_phy_setmedia",
ife->ifm_data));
Let me know what other information I can provide.
Thanks,
Dominic
More information about the freebsd-current
mailing list