malloc question + atapicam problem

Harald Schmalzbauer h.schmalzbauer at
Sun Apr 8 21:47:00 UTC 2007


I've been away from -current for some months, so I'm not sure if phk's malloc 
is still the default in HEAD or the jemalloc is used.
If the latter, is there something like '/etc/malloc.conf -> ajz' ?

And not to forget:

Thanks a lot for that great work!!!

I have some decent new hardware (and thought decent HW obligates [don't know 
if it's correct english but I hope you know what I mean]) and almost 
everything works fine, especially:

pcm0: <HDA Codec: Realtek ALC883>
pcm0: <HDA Driver Revision: 20070320_0043>

	and the ich8 stuff:
ichsmb0: <SMBus controller> port 0x500-0x51f mem 0xf9207000-0xf92070ff irq 18 
at device 31.3 on pci0
ichsmb0: [GIANT-LOCKED]
ichsmb0: [ITHREAD]
smbus0: <System Management Bus> on ichsmb0
atapci2: <Intel ICH8 SATA300 controller> port 
0xd400-0xd407,0xd800-0xd803,0xdc00-0xdc07,0xe000-0xe003,0xe400-0xe41f mem 
0xf9206000-0xf92067ff irq 19 at device 31.2 on pci0
atapci2: [ITHREAD]
atapci2: AHCI Version 01.10 controller with 6 ports detected
ata3: <ATA channel 0> on atapci2
ata3: [ITHREAD]
ata4: <ATA channel 1> on atapci2
ata4: [ITHREAD]
ata5: <ATA channel 2> on atapci2
ata5: [ITHREAD]
ata6: <ATA channel 3> on atapci2
ata6: [ITHREAD]
ata7: <ATA channel 4> on atapci2
ata7: [ITHREAD]
ata8: <ATA channel 5> on atapci2
ata8: [ITHREAD]

	along with the additional P-ATA Controller:
atapci0: <JMicron JMB363 SATA300 controller> mem 0xf9000000-0xf9001fff irq 17 
at device 0.0 on pci4
atapci0: AHCI Version 01.00 controller with 2 ports detected
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
atapci1: <JMicron JMB363 UDMA133 controller> port 
0x9000-0x9007,0x9400-0x9403,0x9800-0x9807,0x9c00-0x9c03,0xa000-0xa00f irq 18 
at device 0.1 on pci4
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]

	And besides the txcsum feature the Marvell GbE is also working fine:
msk0: <Marvell Technology Group Ltd. Yukon EC Id 0xb6 Rev 0x02> on mskc0
msk0: Ethernet address: 00:16:e6:80:cd:51
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E1111 Gigabit PHY> PHY 0 on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, 
mskc0: [FILTER]

Only atapicam prevents the machine from booting.
Any hints are highly appreciated!
Connected to the JMicron (obviously):
acd0: DVDR <HL-DT-ST DVDRAM GSA-H10N/JL10> at ata2-master UDMA33
ATA channel 2:
    Master: acd0 <HL-DT-ST DVDRAM GSA-H10N/JL10> ATA/ATAPI revision 5
    Slave:       no device present
If atapicam is compiled into the kernel the machine stops booting without any 
message after finding the (S-ATA)HD and all the labels and before finding the 
umass disks.



More information about the freebsd-current mailing list