Thoshiba Tecra 8000 with 3com 3CXFE575CT

[Psadi]

M. Warner Losh skrev:

>In message: <43541A46.2050705 at psam.se>
>            Psadi <freebsd at psam.se> writes:
>: M. Warner Losh skrev:
>: 
>: >: When I start it outside and then connect the card it will detect and
>: >: configure it correctly.
>: >
>: >OK.  This is a HUGE clue.  One that shouldn't be overlooked :-).  What
>: >it is telling me is that FUNCTION interrupts aren't getting through,
>: >but STATUS interrupts ARE getting through.  I'll have to go re-read my
>: >two TOPIC data sheets to make sure, but I think that the TOPIC chips,
>: >especially the older ones, have a number of knobs for function
>: >interrupts that are not in the standard bridge chipset.
>: >
>: >Please refresh my recollection: Did this used to work with 5.4?  IIRC,
>: >I did some work to fix o2 micro hangs that disabled the function
>: >interrupts during card insertion by routing them via IRQ 1 (which the
>: >o2micro actually doesn't route, so they just disappear).  Maybe that
>: >work around had bad effects for the TOPIC95B that you have?
>: >
>: >Warner
>: >
>: >
>: >  
>: >
>: I have no problem with the network when I run FreeBSD 5.4. I have no 
>: watchdog timeouts. And I can cvsup the source and ports without any problem.
>: 
>: As a side not ACPI was disable when I tested if it detected the network 
>: card or not when I inserted it. Though since I didnt notice any diffrent 
>: when it was on or off I dont think it has any impact. I did do this test 
>: earlier before you asked but then I just didnt think it was relevant. Of 
>: this I know it works with ACPI on also since I was running with ACPI 
>: when I tried it.
>
>Do you have a second network card, 32- or 16-bits, that you can test
>this with also?  We need to preclude xl driver bustage in general, or
>specific to your submodel as well.
>
>Warner
>_______________________________________________
>freebsd-current at freebsd.org mailing list
>http://lists.freebsd.org/mailman/listinfo/freebsd-current
>To unsubscribe, send any mail to "freebsd-current-unsubscribe at freebsd.org"
>
>
>  
>
I have a 3Com Etherlink III wich identifies as ep0 and using that works 
like a charm :)

pccard0: CIS version PCCARD 2.0 or 2.1
pccard0: CIS info: 3Com Corporation, 3C589, TP/BNC LAN Card Ver. 2a, 000002
pccard0: Manufacturer code 0x101, product 0x589
pccard0: function 0: network adapter, ccr addr 10000 mask 3
pccard0: function 0, config table entry 1: I/O card; irq mask ffff; 
iomask 4, io
space 0-f; io8 io16 irqlevel
pccard0: function 0, config table entry 3: I/O card; irq mask ffff; 
iomask 4, io
space 0-f; io8 io16 irqlevel
ep0: <3Com Corporation 3C589> at port 0x100-0x10f irq 11 function 0 
config 1 on
pccard0
ep0: bpf attached
ep0: Ethernet address: 00:a0:24:ae:be:ad
ep0: [MPSAFE]

There is no wathcdog timeouts on that card and dl a iso image works fine.

Peter