Thoshiba Tecra 8000 with 3com 3CXFE575CT
Doug Rabson
dfr at nlsystems.com
Sun Nov 20 02:52:38 PST 2005
On Monday 17 October 2005 20:06, M. Warner Losh wrote:
> : When I start it outside and then connect the card it will detect
> : and configure it correctly.
>
> OK. This is a HUGE clue. One that shouldn't be overlooked :-).
> What it is telling me is that FUNCTION interrupts aren't getting
> through, but STATUS interrupts ARE getting through. I'll have to go
> re-read my two TOPIC data sheets to make sure, but I think that the
> TOPIC chips, especially the older ones, have a number of knobs for
> function interrupts that are not in the standard bridge chipset.
>
> Please refresh my recollection: Did this used to work with 5.4?
> IIRC, I did some work to fix o2 micro hangs that disabled the
> function interrupts during card insertion by routing them via IRQ 1
> (which the o2micro actually doesn't route, so they just disappear).
> Maybe that work around had bad effects for the TOPIC95B that you
> have?
I get this (xl0 watchdog etc) with my little Sony picturebook, trying to
run current. I'm getting around it using polling for now. I've attached
a verbose dmesg from 7.0 here. This combination works great with 5.4
but getting a dmesg for that configuration would be a bit trickier.
As far as I can see from vmstat, some interrupts are getting through to
irq9 but not the ones that were intended for xl0.
$ vmstat -i
interrupt total rate
irq0: clk 1145039 999
irq1: atkbd0 2 0
irq8: rtc 146591 127
irq9: cbb0 fwohci* 194 0
irq13: npx0 1 0
irq14: ata0 3980 3
Total 1295807 1130
-------------- next part --------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 7.0-CURRENT #0: Sat Nov 19 17:02:31 GMT 2005
dfr at herring.rabson.org:/e/obj/g/dfr/src/sys/VAIO
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xc08b8000.
Preloaded elf module "/boot/kernel/acpi_sony.ko" at 0xc08b8160.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc08b8210.
Calibrating clock(s) ... i8254 clock: 1188408 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 597886417 Hz
CPU: Transmeta(tm) Crusoe(tm) Processor TM5600 (597.89-MHz 586-class CPU)
Origin = "GenuineTMx86" Id = 0x543 Stepping = 3
Features=0x84803f<FPU,VME,DE,PSE,TSC,MSR,CMOV,PN,MMX>
Processor revision 1.3.1.2
Code Morphing Software revision 4.1.4-7-51
20000805 23:30 official release 4.1.4#2
real memory = 184483840 (175 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009afff, 630784 bytes (154 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000000ac9ffff, 168263680 bytes (41080 pages)
avail memory = 170852352 (162 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f6ab0
bios32: Entry = 0xfd870 (c00fd870) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd870+0x11e
pnpbios: Found PnP BIOS data at 0xc00f6ae0
pnpbios: Entry = f0000:a3f8 Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
nfslock: pseudo-device
null: <null device, zero device>
io: <I/O>
random: <entropy source, Software, Yarrow>
mem: <memory>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY P1> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=03951279)
pcibios: BIOS version 2.10
Found $PIR table, 9 entries at 0xc00fdf30
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 7 D 0x63 9
embedded 0 13 A 0x60 9
embedded 0 8 A 0x63 9
embedded 0 9 A 0x62 9
embedded 0 10 A 0x60 9
embedded 0 12 A 0x61 9
embedded 0 11 A 0x61 9
embedded 0 14 A 0x61 9
AcpiOsDerivePciId: bus 0 dev 7 func 2
AcpiOsDerivePciId: bus 0 dev 7 func 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi_ec0: <Embedded Controller: GPE 0x9> port 0x62,0x66 on acpi0
AcpiOsDerivePciId: bus 0 dev 7 func 3
pci_link0: <ACPI PCI Link LNKA> irq 9 on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 9
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 9
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
pci_link1: <ACPI PCI Link LNKB> on acpi0
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
pci_link2: <ACPI PCI Link LNKC> on acpi0
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
pci_link3: <ACPI PCI Link LNKD> irq 9 on acpi0
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 9
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 9
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 9
ACPI timer: 0/1252 0/7 0/5 0/6 0/4 0/252 0/5 0/4 0/4 0/4 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1279, dev=0x0395, revid=0x00
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x2200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base fc000000, size 20, enabled
found-> vendor=0x1279, dev=0x0396, revid=0x00
bus=0, slot=0, func=1
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1279, dev=0x0397, revid=0x00
bus=0, slot=0, func=2
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00001000, size 4, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=9
map[20]: type 4, range 32, base 00001020, size 5, enabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.LNKD:0)
pcib0: slot 7 INTD routed to irq 9 via \\_SB_.LNKD
found-> vendor=0x8086, dev=0x7113, revid=0x03
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[90]: type 4, range 32, base 00001040, size 4, enabled
found-> vendor=0x104c, dev=0x8021, revid=0x02
bus=0, slot=8, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0010, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=255
powerspec 2 supports D0 D2 D3 current D0
map[10]: type 1, range 32, base fc104000, size 11, memory disabled
map[14]: type 1, range 32, base fc100000, size 14, enabled
found-> vendor=0x1073, dev=0x0012, revid=0x00
bus=0, slot=9, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=9
powerspec 1 supports D0 D2 D3 current D0
map[10]: type 1, range 32, base fc108000, size 15, enabled
map[14]: type 4, range 32, base 00001080, size 6, port disabled
map[18]: type 4, range 32, base 00001010, size 2, enabled
pcib0: matched entry for 0.9.INTA (src \\_SB_.LNKC:0)
pci_link2: Picked IRQ 9 with weight 2
pcib0: slot 9 INTA routed to irq 9 via \\_SB_.LNKC
found-> vendor=0x136b, dev=0xff01, revid=0x01
bus=0, slot=11, func=0
class=04-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0010, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x06 (1500 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base fc104800, size 9, memory disabled
found-> vendor=0x1180, dev=0x0475, revid=0x80
bus=0, slot=12, func=0
class=06-07-00, hdrtype=0x02, mfdev=0
cmdreg=0x0007, statreg=0x0a10, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x80 (32000 ns), maxlat=0x07 (1750 ns)
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, enabled
found-> vendor=0x1002, dev=0x4c52, revid=0x64
bus=0, slot=13, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fd000000, size 24, enabled
map[14]: type 4, range 32, base 00001400, size 8, enabled
map[18]: type 1, range 32, base fc105000, size 12, enabled
pcib0: matched entry for 0.13.INTA (src \\_SB_.LNKA:0)
pcib0: slot 13 INTA routed to irq 9 via \\_SB_.LNKA
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1000-0x100f at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0: stat0=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0: stat0=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0: stat0=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=03 ostat1=03
ata1: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: stat1=0x04 err=0x04 lsb=0x04 msb=0x04
ata1: stat1=0x02 err=0x02 lsb=0x02 msb=0x02
ata1: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=01 stat1=00 devices=0x0
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1020-0x103f irq 9 at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1020
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
fwohci0: <Texas Instruments TSB43AA22> mem 0xfc104000-0xfc1047ff,0xfc100000-0xfc103fff at device 8.0 on pci0
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xfc104000
pcib0: matched entry for 0.8.INTA (src \\_SB_.LNKD:0)
pcib0: slot 8 INTA routed to irq 9 via \\_SB_.LNKD
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 08:00:46:03:00:b3:d6:b2
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 0a:00:46:b3:d6:b2
fwe0: bpf attached
fwe0: Ethernet address: 0a:00:46:b3:d6:b2
fwe0: if_start running deferred for Giant
fwip0: <IP over FireWire> on firewire0
fwip0: bpf attached
fwip0: Firewire address: 08:00:46:03:00:b3:d6:b2 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci0: <multimedia, audio> at device 9.0 (no driver attached)
pci0: <multimedia> at device 11.0 (no driver attached)
cbb0: <RF5C475 PCI-CardBus Bridge> at device 12.0 on pci0
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.12.INTA (src \\_SB_.LNKB:0)
pci_link1: Picked IRQ 9 with weight 5
pcib0: slot 12 INTA routed to irq 9 via \\_SB_.LNKB
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0x04751180 0x0a100007 0x06070080 0x00022000
0x10: 0x80000000 0x020000dc 0x20030200 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x07000109
0x40: 0x80b1104d 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00a20001 0x00000000 0x04630463 0x30000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x000f0000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x80b1104d 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0xfe190001
0xe0: 0x24c04000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pci0: <display, VGA> at device 13.0 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
acpi_sony0: <Sony notebook controller> on acpi0
acpi_sony0: PID 1
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xd3fff,0xdc000-0xdffff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
umass0: Sony USB Memory Stick Slot, rev 1.10/1.31, addr 2
umass0:1:0:-1: Attached to scbus1
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 597886417 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
battery0: battery initialization startacpi_acad0: acline initialization start
battery0: battery initialization done, tried 1 times
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
ad0: setting PIO4 on Intel PIIX4 chip
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
ad0: setting UDMA33 on Intel PIIX4 chip
ad0: 11513MB <HITACHI DK23AA-12 00XDA0G4> at ata0-master UDMA33
ad0: 23579136 sectors [23392C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
cardbus0: Resource not specified in CIS: id=14, size=80
cardbus0: Resource not specified in CIS: id=18, size=80
found-> vendor=0x10b7, dev=0x5157, revid=0x01
bus=2, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0x0a (2500 ns), maxlat=0x05 (1250 ns)
intpin=a, irq=9
powerspec 1 supports D0 D1 D2 D3 current D0
xl0: <3Com 3c575B Fast Etherlink XL> port 0x1100-0x117f mem 0x88000000-0x8800007f,0x88000080-0x880000ff irq 9 at device 0.0 on cardbus0
xl0: using port I/O
xl0: media options word: 40
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
tdkphy0: <TDK 78Q2120 media interface> on miibus0
tdkphy0: OUI 0x00c039, model 0x0014, rev. 3
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:10:4b:f6:82:84
xl0: [MPSAFE]
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
(probe3:sbp0:0:3:0): error 22
(probe3:sbp0:0:3:0): Unretryable Error
(probe4:sbp0:0:4:0): error 22
(probe4:sbp0:0:4:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
pass0 at umass-sim0 bus 0 target 0 lun 0
pass0: <Sony MSC-U01N 1.00> Removable Direct Access SCSI-0 device
pass0: 1.000MB/s transfers
GEOM: new disk da0
(da0:umass-sim0:0:0:0): error 6
(da0:umass-sim0:0:0:0): Unretryable Error
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Sony MSC-U01N 1.00> Removable Direct Access SCSI-0 device
da0: 1.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
Unretryable error
(da0:umass-sim0:0:0:0): error 6
(da0:umass-sim0:0:0:0): Unretryable Error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
Unretryable error
(da0:umass-sim0:0:0:0): error 6
(da0:umass-sim0:0:0:0): Unretryable Error
Opened disk da0 -> 6
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
acpi_ec0: info: new max delay is 10 us
More information about the freebsd-current
mailing list