pccard not working on 5.3 beta2

Dave McCammon davemac11 at yahoo.com
Wed Sep 1 17:08:48 PDT 2004

I got a 3com 3c575b pccard that used to 
work on 5.2.1-release-p9 but doesn't on 5.3-beta2.

I've got in /boot/loader.conf

Any and all help is greatly appreciated

5.3 Beta2 dmesg.boot below

Waiting (max 60 seconds) for system process `vnlru' to
Waiting (max 60 seconds) for system process
`bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer'
to stop...
Syncing disks, vnodes remaining...2 2 0 0 done
No buffers busy after final sync
Uptime: 28m53s
cbb1: cbb_power: 0V
cbb1: bad Vcc request. ctrl=0x7720700,
cbb_power: 0V
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,
1991, 1992, 1993, 1994
	The Regents of the University of California. All
rights reserved.
FreeBSD 5.3-BETA2 #0: Tue Aug 31 10:54:22 EST 2004
    root at ion:/usr/obj/usr/src/sys/GREY
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium/P55C (quarter-micron) (199.31-MHz
586-class CPU)
  Origin = "GenuineIntel"  Id = 0x581  Stepping = 1
real memory  = 67108864 (64 MB)
avail memory = 60239872 (57 MB)
Intel Pentium detected, installing workaround for F00F
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 4 Entries> on
pci0: <PCI bus> on pcib0
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port
0xfcf0-0xfcff,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at
device 1.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port
0xfcc0-0xfcdf at device 1.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 1.3 (no driver
pci0: <display, VGA> at device 2.0 (no driver
cbb0: <TI1131 PCI-CardBus Bridge> at device 4.0 on
cbb0: Found memory at 00000000
cbb0: Secondary bus is 0
cbb0: Secondary bus set to 2 subbus 3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: cbb_power: 0V
cbb0: bad Vcc request. ctrl=0xf000ff00,
cbb_power: 0V
cbb1: <TI1131 PCI-CardBus Bridge> at device 4.1 on
cbb1: Found memory at 00001000
cbb1: Secondary bus is 0
cbb1: Secondary bus set to 4 subbus 5
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: cbb_power: 0V
cpu0 on motherboard
orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff on
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port
0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
  Unsupported (pre-v4) Touchpad detected
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <Enhanced floppy controller (i82077, NE72065 or
clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in
ppc0: FIFO with 16/16/7 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0700> can't assign resources (port)
Timecounters tick every 10.000 msec
Interrupt storm detected on "irq10: uhci0"; throttling
interrupt source
Status is 0xf000e2c3
Status is 0x200020
cbb1: card inserted: event=0x07b30020, state=00200020
cbb1: Unknown card voltage
cbb1: CardBus card activation failed
ad0: 2067MB <TOSHIBA MK2104MAV/E4.02 A> [4200/16/63]
at ata0-master WDMA2
ATAPI_RESET time = 10us
acd0: CDROM <TOSHIBA CD-ROM XM-1702BC/1854> at
ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a

Do you Yahoo!?
Yahoo! Mail is new and improved - Check it out!

More information about the freebsd-current mailing list