[5.3BETA7] ad0 gone after suspend/resume cycle
Peter Gade Jensen
rhazn at daimi.au.dk
Wed Oct 13 04:19:54 PDT 2004
I've been seeing this little feature ever since ATAng was introduced and
also reported it back then, but didn't get any real response. Properly my
own fault for not being precise enough. :-) But I better try again
before 5.3 goes stable.
The subject at hand is an 'old' Toshiba Satellite Pro 6000(dmesg
attached) and FreeBSD5.3BETA7 GENERIC kernel+debugging. When I suspend with
'acpiconf -s 3' and afterwards resumes, ad0 is removed with the message:
"ad0: WARNING - removed from configuration."
Trying to track down why this happens, I've come so far that
ata-all.c:ata_identify_devices(ata_channel*) doesn't find anything
after the resume. So, ata-all.c:ata_reinit(ata_channel*) starts by
detaching the devices that were lost during reset(this means ad0), then detaches the
devices that were lost during identify(none) and finally attaching the devices
that were found by ata_identify_devices(I'm guessing here?). In this case
none.
The above is properly a wrong interpretation of the code, but I'm new at
this, so be nice. :o) The question then is: why is my drive lost?
I can't be helpful with a dump, because 1) the laptop doesn't panic()
and 2) it's kind of hard to doadump without a configured drive. :o)
This might not even be something wrong with ATA, but I don't know
whereelse to look.
This is output when resuming with verbose boot:
ata0: reiniting channel ..
ata0: reset tp1 mask=03 ostat0=80 ostat1=80
ad0: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ad0: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ad0: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ad0: stat=0x50 err=0x00 lsb=0xfe msb=0x3f
ata0-slave: stat=0x00 err=0x00 lsb=0xfe msb=0x3f
ata0: reset tp2 stat0=50 stat1=00 devices=0x0
ata0: resetting done ..
ad0: WARNING - removed from configuration
ata0: device config done ..
and the backtrace, when forcing a panic after the call to ata_reinit in
ata_resume:
db> trace
kdb_enter(c0684e14) at kdb_enter+0x2b
panic(c06716ac,c152e600,c152e600,c067169c,c155ec00) at panic+0x127
ata_resume(c155ec00) at ata_resume+0x3a
bus_generic_resume(c1564280) at bus_generic_resume+0x42
bus_generic_resume(c155d700,c18efc40,c06ba5e0,c18efc40,b) at bus_generic_resume+0x42
pci_resume(c155d700) at pci_resume+0x57
bus_generic_resume(c1530100,c1530100,c1530100,cbe92ac4,c07f8b2b) at bus_generic_resume+0x42
acpi_pcib_resume(c1530100,cbe92ad8,c05062d2,c1530100,c1530980) at acpi_pcib_resume+0x13
acpi_pcib_acpi_resume(c1530100) at acpi_pcib_acpi_resume+0xb
bus_generic_resume(c1530980) at bus_generic_resume+0x42
bus_generic_resume(c1530b00) at bus_generic_resume+0x42
bus_generic_resume(c14a7000,4,75003,16,80045003) at bus_generic_resume+0x42
acpi_SetSleepState(c1530900,3,1,cbe92b88,c06e42d8) at acpi_SetSleepState+0x2a0
acpiioctl(c06e42d8,80045003,cbe92c60,3,c1558960) at acpiioctl+0xa3
spec_ioctl(cbe92b88,cbe92c34,c054c1db,cbe92b88,c06db020) at spec_ioctl+0xd7
spec_vnoperate(cbe92b88) at spec_vnoperate+0x13
vn_ioctl(c190e088,80045003,cbe92c60,c190ae80,c1558960) at vn_ioctl+0x19f
ioctl(c1558960,cbe92d14,3,1,292) at ioctl+0x3e0
syscall(2f,2f,2f,bfbfedc0,3) at syscall+0x213
Xint0x80_syscall() at Xint0x80_syscall+0x1f
I don't know if this is enough, but let me know if you need more
information.
Thanks,
Peter
--
"What I like most about myself is that I'm so understanding when I mess
things up."
-------------- next part --------------
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-BETA7 #3: Tue Oct 12 22:02:51 CEST 2004
pgj at aki.playah.dk:/usr/obj/usr/5.0/sys/GENDEBUG
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0822000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc08222bc.
Calibrating clock(s) ... i8254 clock: 1193194 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 995965495 Hz
CPU: Intel(R) Pentium(R) III Mobile CPU 1000MHz (995.97-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 251002880 (239 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x000000000eaf9fff, 233639936 bytes (57041 pages)
avail memory = 236081152 (225 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f00b0
bios32: Entry = 0xf98e9 (c00f98e9) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x97ab
pnpbios: Found PnP BIOS data at 0xc00f0260
pnpbios: Entry = f0000:8d8 Rev = 1.0
pnpbios: Event flag at 510
pnpbios: OEM ID c936f351
Other BIOS signatures found:
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <TOSHIB 750> on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=164410b9)
pcibios: BIOS version 2.10
Found $PIR table, 7 entries at 0xc00f01d0
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 2 A 0x59 11
embedded 0 6 A 0x08 11
embedded 0 17 A 0x01 11
embedded 0 17 B 0x02 11
embedded 0 10 A 0x04 11
embedded 1 0 A 0x03 11
embedded 0 16 A 0x03 11
embedded 0 16 B 0x04 11
embedded 0 18 A 0x01 11
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 1
acpi0: [MPSAFE]
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 3, max = 7, width = 4
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 7, width = 5
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xee08-0xee0b on acpi0
cpu0: <ACPI CPU (3 Cx states)> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI PCI link initial configuration:
\\_SB_.PCI0.FNC0.LNKA irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.17.0
\\_SB_.PCI0.FNC0.LNKB irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.17.1
\\_SB_.PCI0.FNC0.LNKD irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.10.0
\\_SB_.PCI0.FNC0.LNKC irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.16.0
\\_SB_.PCI0.FNC0.LNKD irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.16.1
\\_SB_.PCI0.FNC0.LNKH irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.6.0
\\_SB_.PCI0.FNC0.LNKA irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.18.0
\\_SB_.PCI0.FNC0.LNKG irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 0.2.0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f0000000, size 26, enabled
found-> vendor=0x10b9, dev=0x1644, revid=0x01
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0xa210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D3 current D0
found-> vendor=0x10b9, dev=0x5247, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0400, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base f7eff000, size 12, enabled
pcib0: matched entry for 0.2.INTA (src \\_SB_.PCI0.FNC0.LNKG)
pcib0: possible interrupts: 3 4 5 6 7 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.FNC0.LNKA (references 2, priority 5888):
interrupts: 11 10 5 7 6 4 3
penalty: 80 80 130 5080 5080 5080 5080
\\_SB_.PCI0.FNC0.LNKD (references 2, priority 5888):
interrupts: 11 10 5 7 6 4 3
penalty: 80 80 130 5080 5080 5080 5080
\\_SB_.PCI0.FNC0.LNKB (references 1, priority 2944):
interrupts: 11 10 5 7 6 4 3
penalty: 80 80 130 5080 5080 5080 5080
\\_SB_.PCI0.FNC0.LNKC (references 1, priority 2944):
interrupts: 11 10 5 7 6 4 3
penalty: 80 80 130 5080 5080 5080 5080
\\_SB_.PCI0.FNC0.LNKH (references 1, priority 2944):
interrupts: 11 10 5 7 6 4 3
penalty: 80 80 130 5080 5080 5080 5080
\\_SB_.PCI0.FNC0.LNKG (references 1, priority 2944):
interrupts: 11 10 5 7 6 4 3
penalty: 80 80 130 5080 5080 5080 5080
pcib0: slot 2 INTA routed to irq 11 via \\_SB_.PCI0.FNC0.LNKG
found-> vendor=0x10b9, dev=0x5237, revid=0x03
bus=0, slot=2, func=0
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000eff0, size 4, enabled
found-> vendor=0x10b9, dev=0x5229, revid=0xc3
bus=0, slot=4, func=0
class=01-01-f0, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000ed00, size 8, enabled
map[14]: type 1, range 32, base f7efe000, size 12, enabled
pcib0: matched entry for 0.6.INTA (src \\_SB_.PCI0.FNC0.LNKH)
pcib0: possible interrupts: 3 4 5 6 7 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.FNC0.LNKA (references 2, priority 6051):
interrupts: 10 11 5 7 6 4 3
penalty: 160 170 210 5160 5160 5160 5160
\\_SB_.PCI0.FNC0.LNKD (references 2, priority 6051):
interrupts: 10 11 5 7 6 4 3
penalty: 160 170 210 5160 5160 5160 5160
\\_SB_.PCI0.FNC0.LNKB (references 1, priority 3025):
interrupts: 10 11 5 7 6 4 3
penalty: 160 170 210 5160 5160 5160 5160
\\_SB_.PCI0.FNC0.LNKC (references 1, priority 3025):
interrupts: 10 11 5 7 6 4 3
penalty: 160 170 210 5160 5160 5160 5160
\\_SB_.PCI0.FNC0.LNKH (references 1, priority 3025):
interrupts: 10 11 5 7 6 4 3
penalty: 160 170 210 5160 5160 5160 5160
pcib0: slot 6 INTA routed to irq 11 via \\_SB_.PCI0.FNC0.LNKH
found-> vendor=0x10b9, dev=0x5451, revid=0x01
bus=0, slot=6, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x10b9, dev=0x1533, revid=0x00
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x000f, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D3 current D0
found-> vendor=0x10b9, dev=0x7101, revid=0x00
bus=0, slot=8, func=0
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base f7efd000, size 12, enabled
map[14]: type 4, range 32, base 0000eb40, size 6, enabled
map[18]: type 1, range 32, base f7ec0000, size 17, enabled
pcib0: matched entry for 0.10.INTA (src \\_SB_.PCI0.FNC0.LNKD)
pcib0: possible interrupts: 3 4 5 6 7 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.FNC0.LNKA (references 2, priority 6214):
interrupts: 10 11 5 7 6 4 3
penalty: 240 260 290 5240 5240 5240 5240
\\_SB_.PCI0.FNC0.LNKD (references 2, priority 6214):
interrupts: 10 11 5 7 6 4 3
penalty: 240 260 290 5240 5240 5240 5240
\\_SB_.PCI0.FNC0.LNKB (references 1, priority 3107):
interrupts: 10 11 5 7 6 4 3
penalty: 240 260 290 5240 5240 5240 5240
\\_SB_.PCI0.FNC0.LNKC (references 1, priority 3107):
interrupts: 10 11 5 7 6 4 3
penalty: 240 260 290 5240 5240 5240 5240
pcib0: slot 10 INTA routed to irq 11 via \\_SB_.PCI0.FNC0.LNKD
found-> vendor=0x8086, dev=0x1229, revid=0x0d
bus=0, slot=10, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, memory disabled
found-> vendor=0x1179, dev=0x0617, revid=0x32
bus=0, slot=17, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0000, statreg=0x0490, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 1 supports D0 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, memory disabled
found-> vendor=0x1179, dev=0x0617, revid=0x32
bus=0, slot=17, func=1
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0000, statreg=0x0490, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
powerspec 1 supports D0 D3 current D0
map[10]: type 1, range 32, base f7ebfe00, size 9, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.PCI0.FNC0.LNKA)
pcib0: possible interrupts: 3 4 5 6 7 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.FNC0.LNKA (references 2, priority 6380):
interrupts: 10 11 5 7 6 4 3
penalty: 320 360 370 5320 5320 5320 5320
\\_SB_.PCI0.FNC0.LNKB (references 1, priority 3190):
interrupts: 10 11 5 7 6 4 3
penalty: 320 360 370 5320 5320 5320 5320
\\_SB_.PCI0.FNC0.LNKC (references 1, priority 3190):
interrupts: 10 11 5 7 6 4 3
penalty: 320 360 370 5320 5320 5320 5320
pcib0: slot 18 INTA routed to irq 11 via \\_SB_.PCI0.FNC0.LNKA
found-> vendor=0x1179, dev=0x0805, revid=0x03
bus=0, slot=18, func=0
class=08-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0002, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
agp0: <Ali Generic host to PCI bridge> mem 0xf0000000-0xf3ffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf0000000
agp0: allocating GATT for aperture of size 64M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xf7f00000-0xfdffffff
pcib1: prefetched decode 0xfff00000-0xfffff
ACPI PCI link initial configuration:
\\_SB_.PCI0.FNC0.LNKC irq 0: [ 3 4 5 6 7 10 11] 11+ low,level,sharable 1.0.0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base fc000000, size 25, enabled
pcib1: device (null) requested decoded memory range 0xfc000000-0xfdffffff
map[14]: type 1, range 32, base fbc00000, size 22, enabled
pcib1: device (null) requested decoded memory range 0xfbc00000-0xfbffffff
map[18]: type 1, range 32, base f8000000, size 25, enabled
pcib1: device (null) requested decoded memory range 0xf8000000-0xf9ffffff
map[1c]: type 1, range 32, base f7ff8000, size 15, enabled
pcib1: device (null) requested decoded memory range 0xf7ff8000-0xf7ffffff
pcib1: matched entry for 1.0.INTA (src \\_SB_.PCI0.FNC0.LNKC)
pcib1: possible interrupts: 3 4 5 6 7 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.FNC0.LNKC (references 2, priority 6425):
interrupts: 10 5 11 7 6 4 3
penalty: 340 390 400 5340 5340 5340 5340
\\_SB_.PCI0.FNC0.LNKB (references 1, priority 3212):
interrupts: 10 5 11 3 4 6 7
penalty: 340 390 400 5340 5340 5340 5340
pcib1: slot 0 INTA routed to irq 11 via \\_SB_.PCI0.FNC0.LNKC
found-> vendor=0x1023, dev=0x8820, revid=0x82
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x08 (240 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0xf7eff000-0xf7efffff irq 11 at device 2.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf7eff000
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
atapci0: <AcerLabs Aladdin UDMA66 controller> port 0xeff0-0xefff,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 4.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xeff0
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: [MPSAFE]
pci0: <multimedia, audio> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge, PCI-unknown> at device 8.0 (no driver attached)
fxp0: <Intel 82550 Pro/100 Ethernet> port 0xeb40-0xeb7f mem 0xf7ec0000-0xf7edffff,0xf7efd000-0xf7efdfff irq 11 at device 10.0 on pci0
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf7efd000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 1179 0001 000d
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:00:39:73:e5:b8
fxp0: [MPSAFE]
cbb0: <ToPIC100 PCI-CardBus Bridge> at device 17.0 on pci0
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xfe000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.17.INTA (src \\_SB_.PCI0.FNC0.LNKA)
pcib0: slot 17 INTA is already routed to irq 11
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0x06171179 0x04900007 0x06070032 0x00824000
0x10: 0xfe000000 0x04800080 0x00030300 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffc
0x30: 0x00000000 0x0000fffc 0x00000000 0x0400010b
0x40: 0x00011179 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00010001 0x00800000 0x00000000 0x01000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x860011f0 0x0c000000 0x00008000 0x0000d100
0xb0: 0x3f3f3fcf 0x0a081020 0x10010100 0x00023f00
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00040000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000008
cbb1: <ToPIC100 PCI-CardBus Bridge> at device 17.1 on pci0
cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xfe001000
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib0: matched entry for 0.17.INTB (src \\_SB_.PCI0.FNC0.LNKB)
pcib0: possible interrupts: 3 4 5 6 7 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.FNC0.LNKB (references 1, priority 3307):
interrupts: 10 5 11 7 6 4 3
penalty: 420 470 580 5420 5420 5420 5420
pcib0: slot 17 INTB routed to irq 11 via \\_SB_.PCI0.FNC0.LNKB
cbb1: [MPSAFE]
cbb1: PCI Configuration space:
0x00: 0x06171179 0x04900007 0x06070032 0x00824000
0x10: 0xfe001000 0x04800080 0x00040400 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffc
0x30: 0x00000000 0x0000fffc 0x00000000 0x0400020b
0x40: 0x00011179 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00010001 0x00800000 0x00000000 0x01000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x860021f0 0x0c000000 0x00000000 0x0000d100
0xb0: 0x3f3f3fcf 0x0a081020 0x10010100 0x00023f00
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00040000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000008
pci0: <base peripheral> at device 18.0 (no driver attached)
unknown: not probed (disabled)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0 irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
sio0: irq maps: 0x201 0x211 0x201 0x201
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77a,0x378-0x37a irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
vga: vga0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xe0000-0xeffff,0xc0000-0xcbfff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 04 b0 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x201 0x201 0x201 0x201
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 995965495 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
acpi_cmbat1: battery initialization start
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on AcerLabs Aladdin chip
ata0-master: setting UDMA66 on AcerLabs Aladdin chip
ad0: <TOSHIBA MK2018GAP/M1.42 A> ATA-5 disk at ata0-master
ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA66
GEOM: new disk ad0
[0] f:00 typ:7 s(CHS):0/1/1 e(CHS):1023/5/63 s:63 l:24579387
[1] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/15/63 s:24579450 l:14490630
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 12584646144 end 12584678399
GEOM: Configure ad0s2, start 12584678400 length 7419202560 end 20003880959
GEOM: Configure ad0s2a, start 0 length 1073741824 end 1073741823
GEOM: Configure ad0s2b, start 1073741824 length 536870912 end 1610612735
GEOM: Configure ad0s2c, start 0 length 7419202560 end 7419202559
GEOM: Configure ad0s2d, start 1610612736 length 5808589824 end 7419202559
Mounting root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
More information about the freebsd-current
mailing list