5.3: problems with external USB cdrom

Remo Collet remo at astro.uu.se
Tue Nov 2 02:16:37 PST 2004 

Hi!

  I cannot use the external USB CD/DVD drive (SAMSUNG SN-324F)
on a Dell laptop D400 running 5.3 STABLE (the same device worked 
just fine on 4.9)
 I am aware this issue (or similar ones) has been brought up
in the mailing list already, but I couldn't find
a solution in the archives this time.

When attaching the drive I get the following messages: 

        umass0: Dell USB Drive A01, rev 2.00/1.04, addr 2
        umass0: Get Max Lun not supported (STALLED)
        umass0: Phase Error, residue = 0
        umass0: Phase Error, residue = 0
        umass0: Phase Error, residue = 0
        umass0: Phase Error, residue = 0
        umass0: Phase Error, residue = 0

and detaching it I get:

        umass0: at uhub1 port 2 (addr 2) disconnected
        umass0: detached

I understand from the mail by Paul Koch (Sep 6,2004 "5.3 BETA3 
testing / feedback" ) that it should be possible to get the device
working by "adding some quirks", could anyone be more specific?

Cheers,

Remo


PS boot log attached


---
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.3-STABLE #0: Mon Nov  1 11:17:30 CET 2004
    root at macinino.astro.uu.se:/usr/obj/usr/src/sys/MACININO
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1400MHz (1398.82-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Stepping = 5
  Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,
CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
real memory  = 1072340992 (1022 MB)
avail memory = 1039806464 (991 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL CPi R  > on motherboard
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU (4 Cx states)> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI link \\_SB_.PCI0.LNKB has invalid initial irq 11, ignoring
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0xc000-0xc007 mem 
0xfaf80000-0xfaffffff,0xf0000000-0xf7ffffff irq 11 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 
at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 
at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
umass0: Dell USB Drive A01, rev 2.00/1.04, addr 2
umass0: Get Max Lun not supported (STALLED)
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 
at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ums0: vendor 0x1267 PS/2+USB Mouse, rev 1.10/0.01, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
bge0: <Broadcom BCM5705M Gigabit Ethernet, ASIC rev. 0x3001> mem 
0xfcff0000-0xfcffffff irq 11 at device 0.0 on pci1
miibus0: <MII bus> on bge0
brgphy0: <BCM5705 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 
1000baseTX-FDX, auto
bge0: Ethernet address: 00:0d:56:6d:42:2f
cbb0: <PCI-CardBus Bridge> at device 1.0 on pci1
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <PCI-CardBus Bridge> irq 11 at device 1.1 on pci1
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
fwohci0: <1394 Open Host Controller Interface> mem 
0xfcfe8000-0xfcfebfff,0xfcfef800-0xfcfeffff irq 11 at device 1.2 on pci1
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 32:4f:c0:00:0c:7f:70:10
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 32:4f:c0:7f:70:10
fwe0: Ethernet address: 32:4f:c0:7f:70:10
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci1: <base peripheral> at device 1.3 (no driver attached)
pci1: <network> at device 3.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0xbfa0-0xbfaf,0x376,0x170-0x177,0
x3f6,0x1f0-0x1f7 at device 31.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pcm0: <Intel ICH4 (82801DB)> port 0xdc40-0xdc7f,0xd800-0xd8ff mem 
0xfaeff400-0xfaeff4ff,0xfaeff800-0xfaeff9ff irq 5 at device 31.5 on pci0
pcm0: [GIANT-LOCKED]
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model GlidePoint, device ID 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 1 on 
acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xcf800-0xcffff,0xcf000-0xcf7ff,0xce800-0xceff
f,0xce000-0xce7ff,0xcd800-0xcdfff,0xc0000-0xcd7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounter "TSC" frequency 1398818169 Hz quality 800
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ad0: 57231MB <IC25N060ATMR04-0/MO3OAD0A> [116280/16/63] at ata0-master UDMA100
pccard1: <unknown card> (manufacturer=0x0097, product=0x1620) at function 0
pccard1:    CIS info: TEXAS Instruments, UltraMedia Smart Card Adapter, 1.0
umass0: Phase Error, residue = 0
umass0: Phase Error, residue = 0
umass0: Phase Error, residue = 0
umass0: Phase Error, residue = 0
umass0: Phase Error, residue = 0
Mounting root from ufs:/dev/ad0s3a

More information about the freebsd-current mailing list