Anything to worry about? (failed: rid 0x20 is memory, requested 4)
Daniel Eriksson
daniel_k_eriksson at telia.com
Mon Aug 16 09:52:55 PDT 2004
I just installed a Promise SATA150 TX4 in one of my servers. Everything
seems to work, but I get an error message during boot that worries me a bit:
atapci2: <Promise PDC20318 SATA150 controller> port
0x8800-0x887f,0x9000-0x900f,0x9400-0x943f mem
0xed000000-0xed01ffff,0xed800000-0xed800fff irq 19 at device 11.0 on pci0
atapci2: failed: rid 0x20 is memory, requested 4
atapci2: Reserved 0x20000 bytes for rid 0x20 type 3 at 0xed000000
atapci2: Reserved 0x1000 bytes for rid 0x1c type 3 at 0xed800000
This is with kernel/userland built from sources dated 2004.08.16.13.00.00
(earlier today). The machine has a bunch of PCI cards, and I'm worried that
maybe some important resource allocation fails that later will come around
and bite me.
Hardware:
ASUS A7V600-X motherboard (VIA KT-600 based) with latest BIOS (1005), Athlon
XP2500+, 1.25GB DDR
(onboard VIA 8237 UDMA133 controller)
(onboard VIA 6420 SATA150 controller)
(onboard VIA VT6102 Rhine II NIC)
(onboard VIA 83C572 USB controller)
Adaptec 29160
2 x Highpoint RocketRAID 454
Promise SATA150 TX4
Generic RealTek 8169-based NIC
Attached is the output from "boot -v".
/Daniel Eriksson
-------------- next part --------------
OK boot -v -s
/boot/kernel/acpi.ko text=0x467bc data=0x1cc4+0x110c syms=[0x4+0x6fa0+0x4+0x9311]
KDB: debugger backends: ddb
KDB: current backend: ddb
SMAP type=01 base=0000000000000000 len=000000000009b800
SMAP type=02 base=000000000009b800 len=0000000000004800
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=01 base=0000000000100000 len=000000004fefb000
SMAP type=03 base=000000004fffb000 len=0000000000004000
SMAP type=04 base=000000004ffff000 len=0000000000001000
SMAP type=02 base=00000000fec00000 len=0000000000001000
SMAP type=02 base=00000000fee00000 len=0000000000001000
SMAP type=02 base=00000000ffff0000 len=0000000000010000
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-CURRENT #0: Mon Aug 16 16:46:50 CEST 2004
daniel at xxx.xxx.xxx:/usr/obj/usr/src/sys/FORTIFY
Preloaded elf kernel "/boot/kernel/kernel" at 0xc08ae000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc08ae254.
Table 'FACP' at 0x4fffb0b2
Table 'BOOT' at 0x4fffb030
Table 'APIC' at 0x4fffb058
MADT: Found table at 0x4fffb058
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
ACPI APIC Table: <ASUS A7V600-X>
Calibrating clock(s) ... i8254 clock: 1193207 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1999783191 Hz
CPU: AMD Athlon(TM) XP 2500+ (1999.78-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x6a0 Stepping = 0
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0400000<AMIE,DSP,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory = 1342156800 (1279 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009afff, 630784 bytes (154 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c26000 - 0x000000004e94afff, 1305628672 bytes (318757 pages)
avail memory = 1304936448 (1244 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f2000
bios32: Entry = 0xf1940 (c00f1940) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x1970
pnpbios: Found PnP BIOS data at 0xc00f9cb0
pnpbios: Entry = f0000:9ce0 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 0
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 2
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
MADT: intr override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: low
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: active-high
ioapic0 <Version 0.3> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
null: <null device, zero device>
io: <I/O>
random: <entropy source, Software, Yarrow>
mem: <memory>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <ASUS A7V600-X> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=31891106)
pcibios: BIOS version 2.10
Found $PIR table, 11 entries at 0xc00f1f20
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
slot 1 0 12 A 0x05 3 4 5 7 9 10 11 12
slot 1 0 12 B 0x01 3 4 5 7 9 10 11 12
slot 1 0 12 C 0x02 3 4 5 7 9 10 11 12
slot 1 0 12 D 0x03 3 4 5 7 9 10 11 12
slot 2 0 13 A 0x01 3 4 5 7 9 10 11 12
slot 2 0 13 B 0x02 3 4 5 7 9 10 11 12
slot 2 0 13 C 0x03 3 4 5 7 9 10 11 12
slot 2 0 13 D 0x05 3 4 5 7 9 10 11 12
slot 3 0 14 A 0x02 3 4 5 7 9 10 11 12
slot 3 0 14 B 0x03 3 4 5 7 9 10 11 12
slot 3 0 14 C 0x05 3 4 5 7 9 10 11 12
slot 3 0 14 D 0x01 3 4 5 7 9 10 11 12
slot 4 0 19 A 0x03 3 4 5 7 9 10 11 12
slot 4 0 19 B 0x05 3 4 5 7 9 10 11 12
slot 4 0 19 C 0x01 3 4 5 7 9 10 11 12
slot 4 0 19 D 0x02 3 4 5 7 9 10 11 12
slot 5 0 11 A 0x05 3 4 5 7 9 10 11 12
slot 5 0 11 B 0x01 3 4 5 7 9 10 11 12
slot 5 0 11 C 0x02 3 4 5 7 9 10 11 12
slot 5 0 11 D 0x03 3 4 5 7 9 10 11 12
slot 6 0 10 A 0x01 3 4 5 7 9 10 11 12
slot 6 0 10 B 0x02 3 4 5 7 9 10 11 12
slot 6 0 10 C 0x03 3 4 5 7 9 10 11 12
slot 6 0 10 D 0x05 3 4 5 7 9 10 11 12
slot 7 1 0 A 0x01 3 4 5 7 9 10 11 12
slot 7 1 0 B 0x02 3 4 5 7 9 10 11 12
embedded 0 15 A 0x06 3 4 5 7 9 10 11 12
embedded 0 15 B 0x07 3 4 5 7 9 10 11 12
embedded 0 16 A 0x06 3 4 5 7 9 10 11 12
embedded 0 16 B 0x07 3 4 5 7 9 10 11 12
embedded 0 16 C 0x08 3 4 5 7 9 10 11 12
embedded 0 16 D 0x09 3 4 5 7 9 10 11 12
embedded 0 17 C 0x08 3 4 5 7 9 10 11 12
embedded 0 17 D 0x09 3 4 5 7 9 10 11 12
embedded 0 18 A 0x06 3 4 5 7 9 10 11 12
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 17 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 17 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 15 func 0
acpi0: Power Button (fixed)
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 18 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 2
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 3
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 4
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 5
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
ACPI timer looks GOOD min = 1, max = 2, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI PCI link initial configuration:
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f8000000, size 26, enabled
found-> vendor=0x1106, dev=0x3189, revid=0x80
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0xb198, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 0000d800, size 3, enabled
map[14]: type 4, range 32, base 0000d400, size 2, enabled
map[18]: type 4, range 32, base 0000d000, size 3, enabled
map[1c]: type 4, range 32, base 0000b800, size 2, enabled
map[20]: type 4, range 32, base 0000b400, size 8, enabled
pcib0: matched entry for 0.10.INTA
pcib0: slot 10 INTA hardwired to IRQ 16
found-> vendor=0x1103, dev=0x0008, revid=0x07
bus=0, slot=10, func=0
class=01-04-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=16
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000b000, size 3, enabled
map[14]: type 4, range 32, base 0000a800, size 2, enabled
map[18]: type 4, range 32, base 0000a400, size 3, enabled
map[1c]: type 4, range 32, base 0000a000, size 2, enabled
map[20]: type 4, range 32, base 00009800, size 8, enabled
pcib0: matched entry for 0.10.INTA
pcib0: slot 10 INTA hardwired to IRQ 16
found-> vendor=0x1103, dev=0x0008, revid=0x07
bus=0, slot=10, func=1
class=01-04-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=16
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00009400, size 6, enabled
map[14]: type 4, range 32, base 00009000, size 4, enabled
map[18]: type 4, range 32, base 00008800, size 7, enabled
map[1c]: type 1, range 32, base ed800000, size 12, enabled
map[20]: type 1, range 32, base ed000000, size 17, enabled
pcib0: matched entry for 0.11.INTA
pcib0: slot 11 INTA hardwired to IRQ 19
found-> vendor=0x105a, dev=0x3318, revid=0x02
bus=0, slot=11, func=0
class=01-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0230, cachelnsz=144 (dwords)
lattimer=0x60 (2880 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D3 current D0
map[10]: type 4, range 32, base 00008400, size 8, enabled
map[14]: type 1, range 64, base ec800000, size 12, enabled
pcib0: matched entry for 0.12.INTA
pcib0: slot 12 INTA hardwired to IRQ 19
found-> vendor=0x9005, dev=0x0080, revid=0x02
bus=0, slot=12, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=19
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00008000, size 3, enabled
map[14]: type 4, range 32, base 00007800, size 2, enabled
map[18]: type 4, range 32, base 00007400, size 3, enabled
map[1c]: type 4, range 32, base 00007000, size 2, enabled
map[20]: type 4, range 32, base 00006800, size 8, enabled
pcib0: matched entry for 0.13.INTA
pcib0: slot 13 INTA hardwired to IRQ 16
found-> vendor=0x1103, dev=0x0008, revid=0x07
bus=0, slot=13, func=0
class=01-04-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=16
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00006400, size 3, enabled
map[14]: type 4, range 32, base 00006000, size 2, enabled
map[18]: type 4, range 32, base 00005800, size 3, enabled
map[1c]: type 4, range 32, base 00005400, size 2, enabled
map[20]: type 4, range 32, base 00005000, size 8, enabled
pcib0: matched entry for 0.13.INTA
pcib0: slot 13 INTA hardwired to IRQ 16
found-> vendor=0x1103, dev=0x0008, revid=0x07
bus=0, slot=13, func=1
class=01-04-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=16
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00004800, size 3, enabled
map[14]: type 4, range 32, base 00004400, size 2, enabled
map[18]: type 4, range 32, base 00004000, size 3, enabled
map[1c]: type 4, range 32, base 00003800, size 2, enabled
map[20]: type 4, range 32, base 00003400, size 4, enabled
map[24]: type 4, range 32, base 00003000, size 8, enabled
pcib0: matched entry for 0.15.INTB
pcib0: slot 15 INTB hardwired to IRQ 20
found-> vendor=0x1106, dev=0x3149, revid=0x80
bus=0, slot=15, func=0
class=01-04-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=20
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 00002800, size 4, enabled
pcib0: matched entry for 0.15.INTA
pcib0: slot 15 INTA hardwired to IRQ 20
found-> vendor=0x1106, dev=0x0571, revid=0x06
bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=20
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 00002400, size 5, enabled
pcib0: matched entry for 0.16.INTA
pcib0: slot 16 INTA hardwired to IRQ 21
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 00002000, size 5, enabled
pcib0: matched entry for 0.16.INTA
pcib0: slot 16 INTA hardwired to IRQ 21
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=1
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 00001800, size 5, enabled
pcib0: matched entry for 0.16.INTB
pcib0: slot 16 INTB hardwired to IRQ 21
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=2
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 00001400, size 5, enabled
pcib0: matched entry for 0.16.INTB
pcib0: slot 16 INTB hardwired to IRQ 21
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=3
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ec000000, size 8, enabled
pcib0: matched entry for 0.16.INTC
pcib0: slot 16 INTC hardwired to IRQ 21
found-> vendor=0x1106, dev=0x3104, revid=0x86
bus=0, slot=16, func=4
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x1106, dev=0x3227, revid=0x00
bus=0, slot=17, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00001000, size 8, enabled
map[14]: type 1, range 32, base eb800000, size 8, enabled
pcib0: matched entry for 0.18.INTA
pcib0: slot 18 INTA hardwired to IRQ 23
found-> vendor=0x1106, dev=0x3065, revid=0x78
bus=0, slot=18, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0097, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=23
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 00000800, size 8, enabled
map[14]: type 1, range 32, base eb000000, size 8, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 18
found-> vendor=0x10ec, dev=0x8169, revid=0x10
bus=0, slot=19, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=18
powerspec 2 supports D0 D1 D2 D3 current D0
agp0: <VIA 8377 (Apollo KT400/KT400A/KT600) host to PCI bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf8000000
agp0: allocating GATT for aperture of size 240M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xe000-0xdfff
pcib1: memory decode 0xee000000-0xefdfffff
pcib1: prefetched decode 0xeff00000-0xf7ffffff
ACPI PCI link initial configuration:
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base ee000000, size 24, enabled
pcib1: device (null) requested decoded memory range 0xee000000-0xeeffffff
map[14]: type 3, range 32, base f0000000, size 27, enabled
pcib1: device (null) requested decoded memory range 0xf0000000-0xf7ffffff
pcib1: matched entry for 1.0.INTA
pcib1: slot 0 INTA hardwired to IRQ 16
found-> vendor=0x10de, dev=0x0150, revid=0xa3
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=16
powerspec 1 supports D0 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
atapci0: <HighPoint HPT374 (channel 0+1) UDMA133 controller> port 0xb400-0xb4ff,0xb800-0xb803,0xd000-0xd007,0xd400-0xd403,0xd800-0xd807 irq 16 at device 10.0 on pci0
atapci0: Reserved 0x100 bytes for rid 0x20 type 4 at 0xb400
atapci0: [MPSAFE]
ata2: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xd800
atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xd400
ata2: reset tp1 mask=03 ostat0=50 ostat1=50
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata2: [MPSAFE]
ata3: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xd000
atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xb800
ata3: reset tp1 mask=03 ostat0=50 ostat1=50
ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata3-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata3: [MPSAFE]
atapci1: <HighPoint HPT374 (channel 2+3) UDMA133 controller> port 0x9800-0x98ff,0xa000-0xa003,0xa400-0xa407,0xa800-0xa803,0xb000-0xb007 irq 16 at device 10.1 on pci0
atapci1: Reserved 0x100 bytes for rid 0x20 type 4 at 0x9800
atapci1: [MPSAFE]
ata4: channel #0 on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xb000
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xa800
ata4: reset tp1 mask=03 ostat0=50 ostat1=50
ata4-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata4-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata4: [MPSAFE]
ata5: channel #1 on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xa400
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xa000
ata5: reset tp1 mask=03 ostat0=50 ostat1=50
ata5-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata5-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata5: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata5: [MPSAFE]
atapci2: <Promise PDC20318 SATA150 controller> port 0x8800-0x887f,0x9000-0x900f,0x9400-0x943f mem 0xed000000-0xed01ffff,0xed800000-0xed800fff irq 19 at device 11.0 on pci0
atapci2: failed: rid 0x20 is memory, requested 4
atapci2: Reserved 0x20000 bytes for rid 0x20 type 3 at 0xed000000
atapci2: Reserved 0x1000 bytes for rid 0x1c type 3 at 0xed800000
atapci2: [MPSAFE]
ata6: channel #0 on atapci2
ata6: reset tp1 mask=03 ostat0=80 ostat1=80
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x80 err=0x00 lsb=0x00 msb=0x00
ata6-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata6-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata6: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata6: [MPSAFE]
ata7: channel #1 on atapci2
ata7: reset tp1 mask=03 ostat0=80 ostat1=80
ata7-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata7-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata7: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata7: [MPSAFE]
ata8: channel #2 on atapci2
ata8: reset tp1 mask=03 ostat0=7f ostat1=7f
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8-slave: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata8: reset tp2 stat0=ff stat1=ff devices=0x0
ata8: [MPSAFE]
ata9: channel #3 on atapci2
ata9: reset tp1 mask=03 ostat0=7f ostat1=7f
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9-slave: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata9: reset tp2 stat0=ff stat1=ff devices=0x0
ata9: [MPSAFE]
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0x8400-0x84ff mem 0xec800000-0xec800fff irq 19 at device 12.0 on pci0
ahc0: Defaulting to MEMIO on
ahc0: Reserved 0x1000 bytes for rid 0x14 type 3 at 0xec800000
ahc0: Reading SEEPROM...done.
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 423 instructions downloaded
ahc0: Features 0x1def6, Bugs 0x40, Flags 0x20485560
ahc0: [GIANT-LOCKED]
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
atapci3: <HighPoint HPT374 (channel 0+1) UDMA133 controller> port 0x6800-0x68ff,0x7000-0x7003,0x7400-0x7407,0x7800-0x7803,0x8000-0x8007 irq 16 at device 13.0 on pci0
atapci3: Reserved 0x100 bytes for rid 0x20 type 4 at 0x6800
atapci3: [MPSAFE]
ata10: channel #0 on atapci3
atapci3: Reserved 0x8 bytes for rid 0x10 type 4 at 0x8000
atapci3: Reserved 0x4 bytes for rid 0x14 type 4 at 0x7800
ata10: reset tp1 mask=03 ostat0=50 ostat1=50
ata10-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata10-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata10: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata10: [MPSAFE]
ata11: channel #1 on atapci3
atapci3: Reserved 0x8 bytes for rid 0x18 type 4 at 0x7400
atapci3: Reserved 0x4 bytes for rid 0x1c type 4 at 0x7000
ata11: reset tp1 mask=03 ostat0=50 ostat1=50
ata11-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata11-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata11: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata11: [MPSAFE]
atapci4: <HighPoint HPT374 (channel 2+3) UDMA133 controller> port 0x5000-0x50ff,0x5400-0x5403,0x5800-0x5807,0x6000-0x6003,0x6400-0x6407 irq 16 at device 13.1 on pci0
atapci4: Reserved 0x100 bytes for rid 0x20 type 4 at 0x5000
atapci4: [MPSAFE]
ata12: channel #0 on atapci4
atapci4: Reserved 0x8 bytes for rid 0x10 type 4 at 0x6400
atapci4: Reserved 0x4 bytes for rid 0x14 type 4 at 0x6000
ata12: reset tp1 mask=03 ostat0=50 ostat1=50
ata12-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata12-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata12: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata12: [MPSAFE]
ata13: channel #1 on atapci4
atapci4: Reserved 0x8 bytes for rid 0x18 type 4 at 0x5800
atapci4: Reserved 0x4 bytes for rid 0x1c type 4 at 0x5400
ata13: reset tp1 mask=03 ostat0=50 ostat1=00
ata13-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata13-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata13: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata13: [MPSAFE]
atapci5: <VIA 6420 SATA150 controller> port 0x3000-0x30ff,0x3400-0x340f,0x3800-0x3803,0x4000-0x4007,0x4400-0x4403,0x4800-0x4807 irq 20 at device 15.0 on pci0
atapci5: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3400
atapci5: [MPSAFE]
ata14: channel #0 on atapci5
atapci5: Reserved 0x8 bytes for rid 0x10 type 4 at 0x4800
atapci5: Reserved 0x4 bytes for rid 0x14 type 4 at 0x4400
ata14: reset tp1 mask=03 ostat0=7f ostat1=7f
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14-slave: stat=0x7f err=0xff lsb=0xff msb=0xff
ata14: reset tp2 stat0=ff stat1=ff devices=0x0
ata14: [MPSAFE]
ata15: channel #1 on atapci5
atapci5: Reserved 0x8 bytes for rid 0x18 type 4 at 0x4000
atapci5: Reserved 0x4 bytes for rid 0x1c type 4 at 0x3800
ata15: reset tp1 mask=03 ostat0=7f ostat1=7f
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-master: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15-slave: stat=0x7f err=0xff lsb=0xff msb=0xff
ata15: reset tp2 stat0=ff stat1=ff devices=0x0
ata15: [MPSAFE]
atapci6: <VIA 8237 UDMA133 controller> port 0x2800-0x280f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 20 at device 15.1 on pci0
atapci6: Reserved 0x10 bytes for rid 0x20 type 4 at 0x2800
ata0: channel #0 on atapci6
atapci6: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci6: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90
ata0-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci6
atapci6: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci6: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata1-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0x2400-0x241f irq 21 at device 16.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x2400
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0x2000-0x201f irq 21 at device 16.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x2000
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0x1800-0x181f irq 21 at device 16.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1800
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <VIA 83C572 USB controller> port 0x1400-0x141f irq 21 at device 16.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1400
uhci3: [GIANT-LOCKED]
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xec000000-0xec0000ff irq 21 at device 16.4 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xec000000
ehci0: [GIANT-LOCKED]
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
ehci_pci_attach: companion usb3
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0x1000-0x10ff mem 0xeb800000-0xeb8000ff irq 23 at device 18.0 on pci0
vr0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x1000
miibus0: <MII bus> on vr0
rlphy0: <RTL8201L 10/100 media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: bpf attached
vr0: Ethernet address: 00:0e:a6:1f:29:1e
vr0: [GIANT-LOCKED]
re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x800
re0: <RealTek 8110S Single-chip Gigabit Ethernet> port 0x800-0x8ff mem 0xeb000000-0xeb0000ff irq 18 at device 19.0 on pci0
miibus1: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus1
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re0: bpf attached
re0: Ethernet address: 00:50:fc:f8:c6:81
re0: [GIANT-LOCKED]
fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
unknown: not probed (disabled)
unknown: not probed (disabled)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0xc041 0xc041 0xc041 0xc041
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
unknown: not probed (disabled)
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0xc041 0xc041 0xc041 0xc041
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1999783191 Hz quality 800
Timecounters tick every 1.000 msec
DUMMYNET initialized (011031)
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to accept, logging unlimited
lo0: bpf attached
ata0-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on VIA 8237 chip
ata0-master: setting UDMA100 on VIA 8237 chip
ata0-slave: setting PIO4 on VIA 8237 chip
ata0-slave: setting UDMA100 on VIA 8237 chip
ad0: <ST3120022A/3.06> ATA-6 disk at ata0-master
ad0: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
ar: FreeBSD check1 failed
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:234436482
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 120031478784 end 120031511039
ad1: <ST3120022A/3.06> ATA-6 disk at ata0-slave
ad1: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, UDMA100
ar: FreeBSD check1 failed
GEOM: Configure ad0s1a, start 0 length 536870912 end 536870911
GEOM: Configure ad0s1b, start 536870912 length 536870912 end 1073741823
GEOM: Configure ad0s1c, start 0 length 120031478784 end 120031478783
GEOM: Configure ad0s1d, start 1073741824 length 536870912 end 1610612735
GEOM: Configure ad0s1e, start 1610612736 length 536870912 end 2147483647
GEOM: Configure ad0s1f, start 2147483648 length 10737418240 end 12884901887
GEOM: Configure ad0s1g, start 12884901888 length 107146576896 end 120031478783
GEOM: new disk ad1
ata1-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata1-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata1-master: setting PIO4 on VIA 8237 chip
ata1-master: setting UDMA100 on VIA 8237 chip
ata1-slave: setting PIO4 on VIA 8237 chip
ata1-slave: setting UDMA100 on VIA 8237 chip
ad2: <IC35L120AVV207-0/V24OA66A> ATA-6 disk at ata1-master
ad2: 117800MB (241254720 sectors), 239340 C, 16 H, 63 S, 512 B
ad2: 16 secs/int, 1 depth queue, UDMA100
ar: FreeBSD check1 failed
ad3: <IC35L120AVV207-0/V24OA66A> ATA-6 disk at ata1-slave
ad3: 117800MB (241254720 sectors), 239340 C, 16 H, 63 S, 512 B
ad3: 16 secs/int, 1 depth queue, UDMA100
ar: FreeBSD check1 failed
ata2-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:234436482
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad1s1, start 32256 length 120031478784 end 120031511039
ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
GEOM: new disk ad2
GEOM: new disk ad3
ata2-master: setting PIO4 on HighPoint chip
GEOM: Configure ad1s1b, start 536870912 length 536870912 end 1073741823
GEOM: Configure ad1s1c, start 0 length 120031478784 end 120031478783
GEOM: Configure ad1s1d, start 0 length 536870912 end 536870911
GEOM: Configure ad1s1e, start 1073741824 length 536870912 end 1610612735
GEOM: Configure ad1s1f, start 1610612736 length 536870912 end 2147483647
GEOM: Configure ad1s1g, start 2147483648 length 10737418240 end 12884901887
GEOM: Configure ad1s1h, start 12884901888 length 107146576896 end 120031478783
ata2-master: setting UDMA100 on HighPoint chip
ata2-slave: setting PIO4 on HighPoint chip
ata2-slave: setting UDMA100 on HighPoint chip
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:241248042
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad2s1, start 32256 length 123518997504 end 123519029759
ad4: <WDC WD2500JB-00FUA0/15.05R15> ATA-6 disk at ata2-master
ad4: 238475MB (488397168 sectors), 484521 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA100
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:241248042
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad3s1, start 32256 length 123518997504 end 123519029759
ad5: <WDC WD2500JB-00FUA0/15.05R15> ATA-6 disk at ata2-slave
ad5: 238475MB (488397168 sectors), 484521 C, 16 H, 63 S, 512 B
ad5: 16 secs/int, 1 depth queue, UDMA100
ata3-slave: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
ata3-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
ata3-master: setting PIO4 on HighPoint chip
ata3-master: setting UDMA133 on HighPoint chip
ata3-slave: setting PIO4 on HighPoint chip
ata3-slave: setting UDMA133 on HighPoint chip
ad6: <Maxtor 4A250J0/RAMB1TU0> ATA-7 disk at ata3-master
ad6: 239372MB (490234752 sectors), 486344 C, 16 H, 63 S, 512 B
ad6: 16 secs/int, 1 depth queue, UDMA133
GEOM: Configure ad2s1c, start 0 length 123518997504 end 123518997503
GEOM: Configure ad2s1e, start 0 length 123518997504 end 123518997503
GEOM: new disk ad4
GEOM: Configure ad3s1c, start 0 length 123518997504 end 123518997503
GEOM: Configure ad3s1e, start 0 length 123518997504 end 123518997503
GEOM: new disk ad5
GEOM: new disk ad6
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:976784067
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 32256 length 500113442304 end 500113474559
ad7: <Maxtor 5A250J0/RAMB1TV0> ATA-7 disk at ata3-slave
ad7: 239372MB (490234752 sectors), 486344 C, 16 H, 63 S, 512 B
ad7: 16 secs/int, 1 depth queue, UDMA133
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/14/63 s:63 l:488392002
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad5s1, start 32256 length 250056705024 end 250056737279
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:980462952
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad6s1, start 32256 length 501997031424 end 501997063679
ata4-slave: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
GEOM: Configure ad4s1c, start 0 length 500113442304 end 500113442303
GEOM: Configure ad4s1d, start 0 length 500113442304 end 500113442303
GEOM: new disk ad7
ata4-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
ata4-master: setting PIO4 on HighPoint chip
ata4-master: setting UDMA133 on HighPoint chip
GEOM: Configure ad6s1c, start 0 length 501997031424 end 501997031423
GEOM: Configure ad6s1d, start 0 length 501997031424 end 501997031423
ata4-slave: setting PIO4 on HighPoint chip
ata4-slave: setting UDMA133 on HighPoint chip
ad8: <Maxtor 6Y200P0/YAR41BW0> ATA-7 disk at ata4-master
ad8: 194481MB (398297088 sectors), 395136 C, 16 H, 63 S, 512 B
ad8: 16 secs/int, 1 depth queue, UDMA133
GEOM: new disk ad8
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/7/63 s:63 l:398283417
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad8s1, start 32256 length 203921109504 end 203921141759
ad9: <Maxtor 6Y200P0/YAR41VW0> ATA-7 disk at ata4-slave
ad9: 194481MB (398297088 sectors), 395136 C, 16 H, 63 S, 512 B
ad9: 16 secs/int, 1 depth queue, UDMA133
GEOM: Configure ad8s1c, start 0 length 203921109504 end 203921109503
GEOM: Configure ad8s1d, start 0 length 203921109504 end 203921109503
GEOM: new disk ad9
ata5-slave: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
ata5-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:796582962
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad9s1, start 32256 length 407850476544 end 407850508799
ata5-master: setting PIO4 on HighPoint chip
ata5-master: setting UDMA133 on HighPoint chip
ata5-slave: setting PIO4 on HighPoint chip
ata5-slave: setting UDMA133 on HighPoint chip
GEOM: Configure ad9s1c, start 0 length 407850476544 end 407850476543
GEOM: Configure ad9s1d, start 0 length 407850476544 end 407850476543
ad10: <Maxtor 6Y200P0/YAR41BW0> ATA-7 disk at ata5-master
ad10: 194481MB (398297088 sectors), 395136 C, 16 H, 63 S, 512 B
ad10: 16 secs/int, 1 depth queue, UDMA133
GEOM: new disk ad10
ar: HighPoint check1 failed
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/7/63 s:63 l:398283417
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad10s1, start 32256 length 203921109504 end 203921141759
ad11: <Maxtor 7Y250P0/YAR41BW0> ATA-7 disk at ata5-slave
ad11: 239372MB (490234752 sectors), 486344 C, 16 H, 63 S, 512 B
ad11: 16 secs/int, 1 depth queue, UDMA133
ar: HighPoint check1 failed
GEOM: Configure ad10s1c, start 0 length 203921109504 end 203921109503
GEOM: Configure ad10s1d, start 0 length 203921109504 end 203921109503
GEOM: new disk ad11
ata6-master: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:490223412
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad11s1, start 32256 length 250994386944 end 250994419199
ad12: <Maxtor 7Y250M0/YAR51EW0> ATA-7 disk at ata6-master
ad12: 239372MB (490234752 sectors), 486344 C, 16 H, 63 S, 512 B
ad12: 16 secs/int, 1 depth queue, UDMA133
GEOM: Configure ad11s1c, start 0 length 250994386944 end 250994386943
GEOM: Configure ad11s1d, start 0 length 250994386944 end 250994386943
GEOM: new disk ad12
ar: Promise check1 failed
ata7-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad14: <WDC WD2500JD-00FYB0/02.05D02> ATA-6 disk at ata7-master
ad14: 238475MB (488397168 sectors), 484521 C, 16 H, 63 S, 512 B
ad14: 16 secs/int, 1 depth queue, UDMA100
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:490223412
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad12s1, start 32256 length 250994386944 end 250994419199
ar: Promise check1 failed
GEOM: new disk ad14
ata10-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
GEOM: Configure ad12s1c, start 0 length 250994386944 end 250994386943
GEOM: Configure ad12s1d, start 0 length 250994386944 end 250994386943
ata10-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata10-master: setting PIO4 on HighPoint chip
ata10-master: setting UDMA100 on HighPoint chip
ata10-slave: setting PIO4 on HighPoint chip
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:488392002
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad14s1, start 32256 length 250056705024 end 250056737279
ata10-slave: setting UDMA100 on HighPoint chip
GEOM: Configure ad14a, start 8192 length 500118627328 end 500118635519
GEOM: Configure ad14c, start 0 length 500118635520 end 500118635519
GEOM: Configure ad14s1c, start 0 length 250056705024 end 250056705023
GEOM: Configure ad14s1d, start 0 length 250056705024 end 250056705023
ad20: <IC35L120AVV207-0/V24OA66A> ATA-6 disk at ata10-master
ad20: 117800MB (241254720 sectors), 239340 C, 16 H, 63 S, 512 B
ad20: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad20
ar: HighPoint check1 failed
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:241248042
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad20s1, start 32256 length 123518997504 end 123519029759
ad21: <HDS722512VLAT20/V33OA60A> ATA-6 disk at ata10-slave
ad21: 117800MB (241254720 sectors), 239340 C, 16 H, 63 S, 512 B
ad21: 16 secs/int, 1 depth queue, UDMA100
ar: HighPoint check1 failed
GEOM: Configure ad20s1c, start 0 length 123518997504 end 123518997503
GEOM: Configure ad20s1e, start 0 length 123518997504 end 123518997503
GEOM: new disk ad21
ata11-slave: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:241248042
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad21s1, start 32256 length 123518997504 end 123519029759
ata11-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
ata11-master: setting PIO4 on HighPoint chip
ata11-master: setting UDMA133 on HighPoint chip
GEOM: Configure ad21s1c, start 0 length 123518997504 end 123518997503
GEOM: Configure ad21s1e, start 0 length 123518997504 end 123518997503
ata11-slave: setting PIO4 on HighPoint chip
ata11-slave: setting UDMA133 on HighPoint chip
ad22: <Maxtor 6Y120L0/YAR41BW0> ATA-7 disk at ata11-master
ad22: 117246MB (240121728 sectors), 238216 C, 16 H, 63 S, 512 B
ad22: 16 secs/int, 1 depth queue, UDMA133
GEOM: new disk ad22
ar: HighPoint check1 failed
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:240107427
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad22s1, start 32256 length 122935002624 end 122935034879
ad23: <Maxtor 6Y120L0/YAR41BW0> ATA-7 disk at ata11-slave
ad23: 117246MB (240121728 sectors), 238216 C, 16 H, 63 S, 512 B
ad23: 16 secs/int, 1 depth queue, UDMA133
GEOM: Configure ad22s1c, start 0 length 122935002624 end 122935002623
GEOM: Configure ad22s1e, start 0 length 122935002624 end 122935002623
GEOM: new disk ad23
ata12-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:468873027
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad23s1, start 32256 length 240062989824 end 240063022079
ata12-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
GEOM: Configure ad23s1c, start 0 length 240062989824 end 240062989823
GEOM: Configure ad23s1d, start 0 length 240062989824 end 240062989823
ata12-master: setting PIO4 on HighPoint chip
ata12-master: setting UDMA100 on HighPoint chip
ata12-slave: setting PIO4 on HighPoint chip
ata12-slave: setting UDMA100 on HighPoint chip
ad24: <WDC WD1200JB-00DUA3/75.13B75> ATA-6 disk at ata12-master
ad24: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B
ad24: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad24
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:234436482
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad24s1, start 32256 length 120031478784 end 120031511039
ad25: <IC35L120AVV207-1/V24OA66A> ATA-6 disk at ata12-slave
ad25: 117800MB (241254720 sectors), 239340 C, 16 H, 63 S, 512 B
ad25: 16 secs/int, 1 depth queue, UDMA100
ar: HighPoint check1 failed
GEOM: new disk ad25
ata13-master: pio=0x0c wdma=0x22 udma=0x44 cable=80pin
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:241248042
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad25s1, start 32256 length 123518997504 end 123519029759
ata13-master: setting PIO4 on HighPoint chip
ata13-master: setting UDMA66 on HighPoint chip
GEOM: Configure ad25s1c, start 0 length 123518997504 end 123518997503
GEOM: Configure ad25s1d, start 0 length 123518997504 end 123518997503
ad26: <Maxtor 92732U8/RA530JN0> ATA-5 disk at ata13-master
ad26: 26059MB (53369568 sectors), 52946 C, 16 H, 63 S, 512 B
ad26: 16 secs/int, 1 depth queue, UDMA66
GEOM: new disk ad26
ar: HighPoint check1 failed
lun 0
magic_0 0x411cf9f2
magic_1 0x00000000
flags 0x40102 40102<READY,RAID1>
total_disks 2
generation 0
width 2
heads 255
sectors 63
cylinders 60802
total_sectors 976794336
interleave 128
reserved 10
offset 10
disk 0: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad4
sectors 488397168
disk 1: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad5
sectors 488397168
ar0: 476950MB <ATA RAID0 array> [60802/255/63] status: READY subdisks:
disk0 READY on ad4 at ata2-master
disk1 READY on ad5 at ata2-slave
lun 1
magic_0 0x4100e31f
magic_1 0x00000000
flags 0x40102 40102<READY,RAID1>
total_disks 2
generation 0
width 2
heads 255
sectors 63
cylinders 61031
total_sectors 980469504
interleave 128
reserved 10
offset 10
disk 0: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad6
sectors 490234752
disk 1: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad7
sectors 490234752
ar1: 478744MB <ATA RAID0 array> [61031/255/63] status: READY subdisks:
disk0 READY on ad6 at ata3-master
disk1 READY on ad7 at ata3-slave
lun 2
magic_0 0x4100e40c
magic_1 0x00000000
flags 0x40102 40102<READY,RAID1>
total_disks 2
generation 0
width 2
heads 255
sectors 63
cylinders 49585
total_sectors 796594176
interleave 128
reserved 10
offset 10
disk 0: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad9
sectors 398297088
disk 1: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad8
sectors 398297088
ar2: 388962MB <ATA RAID0 array> [49585/255/63] status: READY subdisks:
disk0 READY on ad9 at ata4-slave
disk1 READY on ad8 at ata4-master
lun 3
magic_0 0x4100e468
magic_1 0x00000000
flags 0x40102 40102<READY,RAID1>
total_disks 2
generation 0
width 2
heads 255
sectors 63
cylinders 29186
total_sectors 468883296
interleave 128
reserved 10
offset 10
disk 0: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad23
sectors 234441648
disk 1: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT>
ad24
sectors 234441648
ar3: 228946MB <ATA RAID0 array> [29186/255/63] status: READY subdisks:
disk0 READY on ad23 at ata11-slave
disk1 READY on ad24 at ata12-master
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:53367867
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad26s1, start 32256 length 27324347904 end 27324380159
GEOM: new disk ar0
GEOM: new disk ar1
GEOM: new disk ar2
GEOM: new disk ar3
GEOM: Configure ad26s1c, start 0 length 27324347904 end 27324347903
GEOM: Configure ad26s1d, start 0 length 27324347904 end 27324347903
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:976784067
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ar0s1, start 32256 length 500113442304 end 500113474559
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:980462952
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ar1s1, start 32256 length 501997031424 end 501997063679
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:796582962
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ar2s1, start 32256 length 407850476544 end 407850508799
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:468873027
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ar3s1, start 32256 length 240062989824 end 240063022079
GEOM: Configure ar0s1c, start 0 length 500113442304 end 500113442303
GEOM: Configure ar0s1d, start 0 length 500113442304 end 500113442303
GEOM: Configure ar1s1c, start 0 length 501997031424 end 501997031423
GEOM: Configure ar1s1d, start 0 length 501997031424 end 501997031423
GEOM: Configure ar2s1c, start 0 length 407850476544 end 407850476543
GEOM: Configure ar2s1d, start 0 length 407850476544 end 407850476543
GEOM: Configure ar3s1c, start 0 length 240062989824 end 240062989823
GEOM: Configure ar3s1d, start 0 length 240062989824 end 240062989823
ahc0: Selection Timeout on A:0. 0 SCBs aborted
ahc0: Selection Timeout on A:1. 0 SCBs aborted
ahc0: Selection Timeout on A:4. 0 SCBs aborted
ahc0: Selection Timeout on A:8. 0 SCBs aborted
ahc0: Selection Timeout on A:9. 0 SCBs aborted
ahc0: Selection Timeout on A:15. 0 SCBs aborted
ahc0: Selection Timeout on A:2. 0 SCBs aborted
ahc0: Selection Timeout on A:3. 0 SCBs aborted
ahc0: Selection Timeout on A:6. 0 SCBs aborted
ahc0: Selection Timeout on A:14. 0 SCBs aborted
(ahc0:A:5:0): Sending SDTR period c, offset 7f
(ahc0:A:5:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
ahc0: target 5 synchronous at 10.0MHz, offset = 0xf
(probe11:ahc0:0:12:0): Retrying Command
(ahc0:A:5:0): Sending SDTR period 19, offset f
(probe12:ahc0:0:13:0): Retrying Command
(probe9:ahc0:0:10:0): Retrying Command
(probe10:ahc0:0:11:0): Retrying Command
(ahc0:A:5:0): Received SDTR period 19, offset f
Filtered to period 19, offset f
(ahc0:A:12:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:12:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 12 using 16bit transfers
ahc0: target 12 synchronous at 80.0MHz DT, offset = 0x3f
(ahc0:A:13:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:13:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 13 using 16bit transfers
ahc0: target 13 synchronous at 80.0MHz DT, offset = 0x3f
(ahc0:A:10:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:10:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 10 using 16bit transfers
ahc0: target 10 synchronous at 80.0MHz DT, offset = 0x3f
(ahc0:A:11:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:11:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 11 using 16bit transfers
ahc0: target 11 synchronous at 80.0MHz DT, offset = 0x3f
pass0 at ahc0 bus 0 target 5 lun 0
pass0: <Seagate STT20000N 6A51> Removable Sequential Access SCSI-2 device
pass0: Serial Number
pass0: 10.000MB/s transfers (10.000MHz, offset 15)
pass1 at ahc0 bus 0 target 10 lun 0
pass1: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device
pass1: Serial Number TFF8Y198
pass1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass2 at ahc0 bus 0 target 11 lun 0
pass2: <IBM IC35L036UWD210-0 S5CQ> Fixed Direct Access SCSI-3 device
pass2: Serial Number VM9B1477
pass2: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass3 at ahc0 bus 0 target 12 lun 0
pass3: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device
pass3: Serial Number TFF8X930
pass3: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass4 at ahc0 bus 0 target 13 lun 0
pass4: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device
pass4: Serial Number VFLA9712
pass4: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
sa0 at ahc0 bus 0 target 5 lun 0
sa0: <Seagate STT20000N 6A51> Removable Sequential Access SCSI-2 device
sa0: Serial Number
sa0: 10.000MB/s transfers (10.000MHz, offset 15)
da0 at ahc0 bus 0 target 10 lun 0
da0: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device
da0: Serial Number TFF8Y198
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da1 at ahc0 bus 0 target 11 lun 0
da1: <IBM IC35L036UWD210-0 S5CQ> Fixed Direct Access SCSI-3 device
da1: Serial Number VM9B1477
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da2 at ahc0 bus 0 target 12 lun 0
da2: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device
da2: Serial Number TFF8X930
da2: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da2: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da3 at ahc0 bus 0 target 13 lun 0
da3: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device
da3: Serial Number VFLA9712
da3: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da3: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
GEOM: new disk da0
GEOM: new disk da1
GEOM: new disk da2
GEOM: new disk da3
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 2 (ISA IRQ 0) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
ioapic0: routing intpin 16 (PCI IRQ 16) to cluster 0
ioapic0: routing intpin 18 (PCI IRQ 18) to cluster 0
ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0
ioapic0: routing intpin 20 (PCI IRQ 20) to cluster 0
ioapic0: routing intpin 21 (PCI IRQ 21) to cluster 0
ioapic0: routing intpin 23 (PCI IRQ 23) to cluster 0
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:71681967
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 32256 length 36701167104 end 36701199359
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:71681967
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da1s1, start 32256 length 36701167104 end 36701199359
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:71681967
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da2s1, start 32256 length 36701167104 end 36701199359
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:71681967
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da3s1, start 32256 length 36701167104 end 36701199359
GEOM: Configure da0s1c, start 0 length 36701167104 end 36701167103
GEOM: Configure da0s1d, start 0 length 36701167104 end 36701167103
GEOM: Configure da1s1c, start 0 length 36701167104 end 36701167103
GEOM: Configure da1s1d, start 0 length 36701167104 end 36701167103
GEOM: Configure da2s1c, start 0 length 36701167104 end 36701167103
GEOM: Configure da2s1d, start 0 length 36701167104 end 36701167103
GEOM: Configure da3s1c, start 0 length 36701167104 end 36701167103
GEOM: Configure da3s1d, start 0 length 36701167104 end 36701167103
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
Enter full pathname of shell or RETURN for /bin/sh:
More information about the freebsd-current
mailing list